N7384-613 Sutton 4 Light Pendant
Product Information
The N7384-613 fixture is a new product that was manufactured on
May 30, 2022. The fixture includes a mounting plate, a support
cable, a rod, a canopy, and shades. The fixture is designed to hold
four medium base bulbs with a maximum wattage of 100 watts each or
CFL or LED equivalents.
Product Usage Instructions
- Shut off the power at the circuit breaker and remove the old
fixture, including the mounting hardware. - Carefully unpack the new fixture and lay out all the parts on a
clean area. Take care not to lose any small parts necessary for
installation. - Secure rod (L) to fixture body (K) using screws (J). Then place
larger cloth shade (H) onto fixture body (K) and secure with screws
(I). - Determine desired hanging height and thread rods (F1,F2,F3) to
all thread (R) on fixture body (K). Attach canopy (D) by threading
onto rod (F1). Carefully pass wires through each rod during
assembly. Note: Remove all thread, if installing with one 6 rod
only. - Position mounting plate (A) on ceiling and mark location of two
mounting holes. Drill holes on ceiling and insert plastic anchors
(P). - Attach mounting plate (A) to junction box (not included) using
mounting screws (B) (Size: #8-32N*L0.5) and wood screws (Q) into
drywall anchors (P). The side of mounting plate marked GND must
face out. - The support cable is provided to support the weight of fixture
while wiring. Align fixture to mounting plate (A) and attach hook
(G) on the end of support cable (C) into a slot located on mounting
plate (A). Carefully allow the support cable (C) to support weight
of fixture while wiring. - Connect the electrical wires as shown in Fig.2, making sure
that all wire connectors are secured. If your junction box has a
ground wire (green or bare copper), connect fixture’s ground wire
to it. Otherwise, connect fixture’s ground wire directly to
mounting plate (A) using green screw provided. - Tuck the wire connections neatly into junction box.
- Place canopy (D) over mounting plate (A) and secure with screws
(E). - Install (4) four medium base bulbs (M) up to 100 watts each or
CFL or LED equivalent (not included) in accordance with the fixture
specification–DO NOT EXCEED THE MAXIMUM WATTAGE RATING! - Secure rod (W) into all thread (O). Then secure lower cloth
shade (Q) to fixture body (K) using screws (I). - Place glass shade (U) followed by metal washer (T) over bottom
of rod (W). Then fasten with hex nut (X). - Place metal cover (S) over rod (W) and secure with finial
(V). - Turn on the power and test the fixture.
INSTALLATION INSTRUCTIONS
Item#N7384-613 (New. 2022/05/30) READ AND SAVE THESE INSTRUCTIONS
W AR N I N G ! S HU T P O WE R O F F AT F U S E O R CI R C UI T B R E AK E R .
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR.
MOUNTING THE FIXTURE (Fig.1)
Fig. 1
1. Shut off the power at the circuit breaker and remove the Set#A-021-143D
old fixture, including the mounting hardware. 2. Carefully unpack your new fixture and lay out all the parts
-Mounting Screw *2 -Ground Screw
P A
on a clean area. Take care not to lose any small parts -Mounting Plate necessary for installation. 3. Secure rod (L) to fixture body (K) using screws (J). Then
B Q D
place larger cloth shade (H) onto fixture body (K) and secure with screws (I).
E
4. Determine desired hanging height and thread rods
(F1,F2,F3) to all thread (R) on fixture body (K). Attach
F1
canopy (D) by threading onto rod (F1). Carefully pass wires through each rod during assembly. Note: Remove
F2
all thread, if installing with one 6″ rod only.
F3
5. Position mounting plate (A) on ceiling and mark location
of two mounting holes. Drill holes on ceiling and insert
plastic anchors (P). 6. Attach mounting plate (A) to junction box (not included)
using mounting screws (B) (Size: #8-32N*L0.5″) and
wood screws (Q) into drywall anchors (P). The side of
mounting plate marked “GND” must face out.
7. The support cable is provided to support the weight of
R
fixture while wiring. Align fixture to mounting plate (A) and
attach hook (G) on the end of support cable (C) into a slot
located on mounting plate (A). Carefully allow the support
cable (C) to support weight of fixture while wiring (Fig.1).
CONNECTING THE WIRES (Fig. 2)
8. Connect the electrical wires as shown in Fig.2, making
W
sure that all wire connectors are secured. If your junction
box has a ground wire (green or bare copper), connect
fixture’s ground wire to it. Otherwise, connect fixture’s
ground wire directly to mounting plate (A) using green
screw provided.
9. Tuck the wire connections neatly into junction box.
FINISHING THE INSTALLATION (Fig.1)
10. Place canopy (D) over mounting plate (A) and secure
with screws (E). 11. Install (4) four medium base bulbs (M) up to 100 watts
each or CFL or LED equivalent (not included) in
accordance with the fixture specification–DO NOT
EXCEED THE MAXIMUM WATTAGE RATING! (NE PAS Rod# W35-1-613 *1 (F1)
X
DEPASSER LA PUISSANCE NOMINALE MAXIMALE!
W35-1-613 *2 (F2)
12. Secure rod (W) into all thread (O). Then secure lower
W35-H-613 *1 (F3)
V
cloth shade (Q) to fixture body (K) using screws (I).
13. Place glass shade (U) followed by metal washer (T)
over bottom of rod (W). Then fasten with hex nut (X).
Fig. 2
14. Place metal cover (S) over rod (W) and secure with finial (V).
FIXTURE WIRES Black or Smooth
FIXTURE WIRES White or Ribbed
Your installation is now complete. Return power and test the fixture.
Note: Illustration (Fig.1) on this manual is for installation purposes only. It may or may not be identical to the fixture purchased.
HOUSE WIRES Black (Hot)
HOUSE WIRES White (Neutral)
C
O T S
FIXTURE WIRES Green or Bare Copper (Ground)
G
H I J K L M Q I U
HOUSE WIRES Green (Ground)
Page: 1/1
LA-3538E
