098029P Zara Plug-In Wall Sconce
Product Information: Zara Plug-In Wall Sconce
The Zara Plug-In Wall Sconce is a lighting fixture designed for
indoor use only. It comes with a three-prong plug and is equipped
with a shade, socket rings, sockets, backplate, switch, cord cover,
mounting plate, cord cover connector, screws, anchors, plug cord,
tapping screws, and a plug screw. The sconce requires a 40-watt E12
candelabra bulb or LED equivalent (not included).
It is important to follow the safety instructions provided to
reduce the risk of fire, electrical shock, and personal injury.
Avoid modifying the plug or power cord and do not exceed the
recommended bulb wattage. Use only the specified type of bulb and
keep flammable materials away from the bulb. Do not open the
product or alter the wiring.
Prior to installation, ensure that there is no existing wiring
behind the wall and check for studs to ensure a sturdy installation
site. If there are no studs, use the provided anchors. If
converting the sconce to a hardwire fixture, it is recommended to
consult a licensed electrician and shut off the main electrical
supply at the fuse box/circuit breaker first.
Care and cleaning of the sconce should be done using a soft dry
cloth. Avoid using cleaners, scouring pads, or similar abrasive
materials.
Product Usage Instructions
- Before starting installation, read the instructions
completely. - Ensure there is no existing wiring behind the wall and check
for studs at the installation site. - Remove all parts from the carton and do not discard any
parts. - Draw a 2-1/8 vertical line on the wall at the desired location
for the wall sconce. Ensure the line is plumb. - Position the Mounting Plate (G) on the wall, aligning it with
the drawn line. Insert a pencil through the Keyhole Slots and mark
the wall. - Drill small pilot holes at the marked locations on the wall.
Use the provided Wall Anchors (K) and insert them into the drilled
holes. Attach the Mounting Plate (G) to the wall using the Tapping
Screws (L). Attach the Backplate to the Mounting Plate using Screws
(F). - Install Cord Covers (F) by connecting them with the Cord Cover
Connector (J) to the lamp. - Remove Socket Rings (B) and place the Shade (A) over the
Sockets (C). Secure the Shade with Socket Rings. - If converting to a hardwire fixture, consult a licensed
electrician and shut off the main electrical supply at the fuse
box/circuit breaker. Use the Plug Screw (M) to cover the plug on
the fixture. - Install proper light bulbs (40-watt E12 candelabra bulb or LED
equivalent) into the Sockets (C).
If troubleshooting is required and the lighting fixture still
does not work, contact your local Ethan Allen Design Center for
assistance.
Zara Plug-In Wall Sconce Assembly Instructions
098029P / 098030P
IMPORTANT SAFETY INSTRUCTIONS TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, AND PERSONAL INJURY: This lighting fixture is for indoor use only. This lamp is equipped with a three-prong plug. DO NOT MODIFY the plug or power cord in any way. DO NOT EXCEED the recommended bulb wattage. Use only the type of bulb specified. Keep flammable materials away from bulb. DO NOT OPEN the product or alter the wiring in any manner. Extension cord: Follow precautions provided with power cord.
READ THESE INSTRUCTIONS COMPLETELY BEFORE STARTING. This lighting fixture is for indoor use only.
CAUTION: Prior to installation, locate ALL INCLUDED PARTS before disposing of packaging materials. TOOLS REQUIRED FOR INSTALLATION:
1. Screwdrivers 2. Drill
3. Hammer
Note: Lightbulb(s) are not included. See light fixture for bulb specification.
Parts Included (refer to figure):
Part A B C
Qty. Description 1 Shade 2 Socket ring 2 Socket
Part D E F
Qty. Description 1 Backplate 1 Switch 2 Cord cover
Part Qty. Description Part Qty. Description
G 1 Mounting plate J 1 Cord cover connector
H 3 Screw
K 2 Anchor
I 1 Plug cord
L 2 Tapping screw
M 1 Plug screw
Assembly Procedure (refer to figures)
1. Prior to installation, ensure that no wiring exists behind the wall you are using for installation. Check for studs in the wall to ensure a sturdy installation site. If there are no studs at the installation site, be sure to use Anchors (K) in Step 5 below.
2. Remove all parts from carton. Do not throw away any parts.
3. Draw a 2-1/8″ vertical line on the wall, centered where you want the wall sconce. Be sure the line is plumb.
4. Position the Mounting Plate (G) so that it is bisected by the line drawn on the wall. Insert a pencil through the Keyhole Slots and mark the wall.
5. Drill small pilot holes at marked locations on the wall. Holes should be sized so they accommodate the Wall Anchors (K) provided. Insert Wall Anchors (K) into drilled holes. Mount the Mounting Plate (G) onto the wall by drilling Tapping Screws (L) into Wall Anchors (K). Attach Backplate to Mounting Plate using Screws (F).
6. Install Cord Covers (F) connecting with Cord Cover Connector (J) to the lamp.
Page 1 of 2
©Ethan Allen Global, Inc.
7. Remove Socket Rings (B). Place the Shade (A) over the Sockets (C) and secure with Socket Rings (B).
8. If the sconce is being converted to a hardwire fixture, a licensed electrician must wire it. In this case, SHUT OFF THE MAIN ELECTRICAL SUPPLY AT FUSE BOX/CIRCUIT BREAKER FIRST. Then, the Plug Screw (M) can be used to cover the plug on the fixture.
9. Install proper light bulbs (40-watt E12 candelabra bulb or LED equivalent) into Sockets (C).
IMPORTANT SAFETY INSTRUCTIONS to convert to direct-wired lighting. We strongly recommend that all direct-wired lighting products be installed by a licensed electrician. Two people may be required for installation. DO NOT EXCEED the rated bulb wattage. Keep flammable materials away from bulb. This light fixture is shipped with all internal wiring intact. Do not open the product or alter the wiring. If installing as a hardwired fixture, installation requires an electrical junction box in the wall sufficient to support the weight of the light fixture.
WARNING: If installing as a hardwired fixture, be certain that the power to the electrical junction box is turned off at the circuit breaker before installation. Turning the power off at a light switch is not sufficient to prevent electrical shock. Then, the Plug Screw (M) can be used to cover the plug on the fixture.
Care and Cleaning:
1. Wipe with a soft dry cloth. 2. AVOID cleaners, scouring pads, etc.
After troubleshooting, if the lighting fixture still does not work, contact your local Ethan Allen Design Center.
Page 2 of 2
SAVE THESE INSTRUCTIONS
©2023 Ethan Allen Global, Inc.
