VLB5 2MP HD TV1 IR Bullet Camera
Product Information:
The VLB5/VLB6/VLD5/VLD6M/VLT7 camera series is the latest
technology in surveillance systems. It features high definition and
sensitivity, low noise and distortion, and supports HD video
transmission using a common coaxial cable. The camera series is
designed to meet the requirements of HD monitoring in traditional
surveillance systems.
Warnings:
– Speco Technologies reserves the right to modify product design
and specifications without notice.
Installation:
– Before installation, ensure that the wall or ceiling is strong
enough to withstand three times the weight of the camera.
– Install and use the camera in a dry environment.
– For VLB5/VLB6 cameras, follow the steps below:
- Drill screw holes and cable hole on the wall according to the
provided drill template. - Route and connect the cables.
- Secure the mounting base with the camera to the wall using
screws. - Adjust the bracket for optimal view angle.
- Perform focus and zoom adjustment if necessary.
– For Dome Cameras (VLD5/VLD6M), follow the steps below:
- Attach the drill template to the desired location on the wall
and drill screw holes and cable hole accordingly. - Rotate the trim ring anticlockwise to remove it from the
camera. - Loosen the screws to open the lower dome and route/connect the
cables. - Secure the camera to the wall using screws provided.
- Perform three-axis adjustment for optimal angle.
- Install the lower dome back and fix it with screws. Then put
the trim ring onto the lower dome and rotate it clockwise until
locked. Remove the protection film.
– For VLT7 cameras, loosen the set screw to disassemble the
camera.
Backlight Compensation (BLC):
When the back of the captured object is too bright, you can set
BLC for the captured object to make it clearer.
Video Output:
The camera supports four video output modes: AHD, TVI, CVI, and
CVBS. To switch between video outputs:
- Remove the cover of the video switch cable.
- Hold and press the button in the video switch cable for 5
seconds to switch the current video output.
Cables:
The camera requires the following cables:
- Video Output Cable
- Power Cable
Please refer to the user manual for more detailed information
and instructions.
VLB5 /VLB6/VLD5/VLD6M/VLT7
User Manual
Thank you for purchasing our product. Speco Technologies is constantly developing and improving products. We reserve the right to modify product design and specifications without notice and without incurring any obligation.
Warnings
If the product does not work properly, please contact the dealer or where the product was purchased. Speco Technologies is not responsible for any problems caused by improper operation or repair. Do not expose the unit to heavy stress, violent vibration or long-term exposure to water and humidity during transportation, storage, and/or installation. Do not install near sources of heat. Only install the product in environments inside the specification operating temperature and humidity range. Do not install the camera near power lines, radar equipment or other electromagnetic radiation. Do not block any ventilation openings if any. Use all the weatherproofing hardware requirement to minimize weather intrusion.
Introduction
This camera series is the latest technology and advanced circuit design, which features high definition and sensitivity, low noise and distortion and supports HD video transmission with the common coaxial cable, ensuring the requirement of the HD monitoring in the traditional surveillance system.
High Resolution Adopt high performance sensor, providing high definition and clear image. High Transmission Performance Real-time transmission with high speed and long distance. DNR Reduce noise from brightness and color signal. OSD Access the camera settings which can be clearly displayed through the main menu. White Balance Adjust the color temperature according to the environment automatically. ICR Auto Switch The filter will filter infrared light during the daytime and change to normal at night to ensure a high sensitivity and clear image. AGC Adjust the gain of amplifier, enabling the camera to output the standard video signal in different lighting condition. Wide Dynamic Range (WDR) When there are both very bright and very dark areas simultaneously in the field of view, this function will balance the brightness level and provide clear images.
1
Backlight Compensation (BLC) When the back of the captured object is too much bright, you can set BLC for the captured object to make it clearer.
Cables
Video Output
Video Switch Cable Power Cable
Video Switch: Four video output modes can be optional–AHD, TVI, CVI and CVBS (a) remove the cover of the video switch cable; (b) hold and press the button in the video switch cable for 5 seconds to switch the current video output.
Installation
Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera. Please install and use the camera in the dry environment. You’d better install back the lens cover or lower dome less than 4 hours after removing it. The mounting types of cameras are only for reference.
Mounting for VLB5/VLB6
1. Drill the screw holes and the cable hole on the wall according to the drill template.
48mm
4.5
48mm
48mm
48mm
4.6
VLB5
VLB6
2
2. Route and connect the cables . 3. Secure the mounting base with camera to the wall with screws as shown below.
Rubber plug
VLB5
VLB6
4. Bracket adjustment. Before adjustment, preview the image of the camera on a monitor and then loosen the fixed ring to adjust the view angle of the camera. Tighten the fixed ring after the adjustment. 5. Focus and zoom adjustment ( If the camera you get is fixed lens, please skip this step). Open the cover of the camera then adjust the focus and zoom screws to get a clear image. Finally, install the cover back to the camera.
Fixed Ring Tilt 80°
Pan 360°
Fixed Ring 360° Rotation
360° Pan 90° Tilt
Focus Zoom
VLB5
Cover
VLB6
Mounting for Dome Camera Mounting for VLD5/VLD6M
1.Attach the drill template to the place where you want to fix the camera and then drill the screw holes and the cable hole on the wall according to the drill template.
3
74.3
(mm)
74.3
90.2mm
4.6 90.2mm
VLD5
VLD6M
2. Rotate the trim ring anticlockwise to remove it from the camera. 3. Loosen the screws to open the lower dome. Then route and connect the cables. 4. Secure the camera to the wall with screws provided as shown below.
Trim ring
Rubber plug * Install it when routing the cables through the ceiling.
Lower dome
5. Three-axis adjustment. Before adjustment, preview the image of the camera on a monitor and then adjust the camera according to the figure below to get an optimum angle.
Pan 0°~355°
Tilt 0°~67° Rotation 0°~355° VLD5
Rotation 0°~345°
Pan 0°~345° Tilt 0°~77° Turn
VLD6M 4
6. Install the lower dome back to the camera and fix it with screws. Then put the trim ring onto the lower dome and then rotate it clockwise until it is locked. Finally, remove the protection film softly.
Trim ring
Mounting for VLT7 1. Loosen the set screw to disassemble the camera.
Set Screw Mounting Base Enclosure Camera Unit
2. Attach the drill template to the place where you want to fix the camera and then drill the screw holes and the cable hole on the wall according to the drill template. 3. Route and connect the cables. Then secure the mounting base to the ceiling or wall with the screws provided.
5
(mm) 44.2
Ø91.6
38.2 Ø51.0
Ø4.5
4. Install the camera unit and enclosure to the mounting base and then adjust the dome to obtain an optimum view angle.
5. Finally, secure the camera with the set screw.
Pan: 360° Tilt: 75°
6
Specifications
Models Specifications
Camera Image Sensor Resolution Image size Video Output Image System Electronic Shutter IR Distance (feet) Frame Rate Min. Illumination
Lens
Lens Mount S/N Ratio Ingress Protection Functions Function Control Day &Night WDR Digital NR AGC Auto White Balance Front Light Compensation Defog HLC Sharpness Mirror Smart IR Image Setting Defect Correction Others Power Supply Power Consumption Working Environment Dimensions (inch)
VLB5
VLB6
VLD5
VLD6M
VLT7
1/2.9″ CMOS 2MP 1920×1080 AHD/TVI/CVI/CVBS (*camera comes defaulted to HD-TVI) PAL/NTSC Auto; 1/50s~1/100000s(PAL);1/60s~1/100000s (NTSC) 65.6~98.4 98.4~164.0 32.8~65.6 65.6~98.4 65.6~98.4 30fps(60Hz),25fps(50Hz) Color:[email protected], AGC ON; B/W: 0lux with IR
2.8mm
2.8~12mm (varifocal)
2.8mm
2.8~12mm (motorized)
2.8mm
M12
D14
52dB(AGC OFF)
IP67
IP67
M12
D14
IP67&IK10 IP67&IK10
M12 IP67
OSD (UTC control)
ICR
Yes (digital WDR)
Yes
Yes
Yes
Yes
No
No
No
No
Yes
Yes
Yes
Auto
120dB
Yes
Yes
Yes
DC12V (± 10%)
DC12V (± 15%)
IR OFF: < 1W; IR ON : < 3.5W
-4 °F ~ 122 °F, 10 % ~ 90 %(relative humidity) 6.6×2.9×2.9 8.6×3.2×3.2 4.7 × 3.5 5.6 × 3.9
3.7×3.3
7
Model: VLB5 /VLB6/VLD5/VLD6M/VLT7
Federal Communications Commission (FCC) Statements
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Responsible Party:
Speco Technologies 200 New Highway Amityville, NY 11701 www.specotech.com
Home | Speco Technologies
