78959 Pacto 10W Track Head
Product Information
The product is a light fitting that requires a supply voltage of
220-240 V~ and 50 Hz. It contains a non-replaceable 10W LED module
(SMD) with a color temperature of 4000K for bulb type
78959/78960/78961 and 3000K for type 94061/94062/94063. The light
source has an energy efficiency class E rating. The product is
Class 1 and must be connected to earth. It conforms to all relevant
UKCA and EC Directive requirements. The product is suitable for
dimming. The minimum distance from lighted objects should be 0.5
meters.
The product comes with a Pacto Track system that can be extended
to various configurations using accessories like left bends, right
bends, T junctions, X junctions, and flexible joints. The track
accessory dimensions are 183.0mm x 35.0mm, and the dead end
dimensions are 182.0mm x 35.0mm. The product has a UK manufacturer
with an address at BH17 7BY and a Brilliant AG EU manufacturer with
an address at Brilliantstrasse 1, D-27442 Gnarrenburg. For more
information, visit https://www.lighting-info.co.uk/78959.
Product Usage
Before installation, carefully note the position of each set of
wires of the existing fitting that needs to be completely removed.
Also, switch off the power at the fuse board and the luminaire
before installation or maintenance.
The correct fixings should be used for brick, cavity walls, or
plasterboard during installation.
To connect the supply wires to the terminal block, remove the
cover from the live end by undoing the screw and push out the
desired cable access point. Identify the correct cable from the
supply and pull it through. Connect the supply wires to the
terminal block opposite the corresponding wires from the fitting.
The central connector can also be wired this way. Refit the cover
onto the live end, taking care not to trap the cable. The remaining
earth tab needs to be inserted into Earth conductor to ensure Earth
continuity.
Do not dispose of waste electrical products with household
waste. Recycle where facilities exist and check with your Local
Authority or local store for recycling advice.
Fitting Units
Locate the product in the track with the connections in the slot. Slide the tab down, and rotate the product 90º to engage the connections in the track. Allow the tab to slide back up and ensure that it is located correctly in the track slot. Replace fuse or circuit breaker and switch on. Your light is now ready for use.
Technical data
Supply Voltage:
220-240 V~, 50 Hz
Bulb
78959 / 78960 / 78961–10W LED module (SMD), 4000K
Type:
94061/ 94062 / 94063 –10W LED module (SMD), 3000K
This product contains a light source of energy efficiency class E.
Non-replaceable light source
Non-replaceable control gear
Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
This product is Class 1, must be connected to earth.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice. This product is suitable for dimming.
0,5m Minimum distance from lighted objects (0.5 metres)
Care and Safety
· We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish.
· Always disconnect the product from mains at least 10 minutes allowing to cool down before any maintenance or adjustment.
· For your safety, always switch off the power supply before cleaning.
Instruction manual
Pacto Track
78959, 78960, 78961, 94061, 94062, 94063
For further information, please visit https://www.lighting-info.co.uk/78959
V4 06/06/2022 UK Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
183.0mm 35.0mm
Thank you for purchasing this light fitting. Please read the instruction carefully before use to ensure safe and satisfactory operation of this product. Please retain these instruction for future reference.
Warning
This is a Class 1 product and must be earthed. Please read these instructions carefully before commencing any work. This unit must be fitted by a competent and qualified electrician. Check the pack and make sure you have all the parts listed. Install in accordance with the IEE Wiring regulations and current Building Regulations. To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician. This light fitting should be connected to a fused circuit If replacing an existing fitting, make a careful note of the connections.
This product is suitable for indoor use only, on normal flammable surfaces. Only to be installed outside arms reach. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced. This track is suitable for dimming. Fittings with low voltage lamps are not suitable for dimming. Care must be taken to only use the same type of fitting that is able to be dimmed, and that the dimmer wattage must not be exceeded. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Layout
This track system can be extended to a variety of different configurations using accessories such as left bends, right bends, T jucntions, X junctions and flexible joints.
TJunction
X Junction
Bend
Track Accessory:
183.0mm 35.0mm
1000.0mm
2000.0mm 3000.0mm
Dead End
182.0mm 183.0mm
35.0mm
35.0mm
35.5mm
108.0mm 79.5mm 294.0mm
108.0mm
108.0mm
35.0mm
16.5mm
35.0mm 43.0mm
40.0mm
108.0mm 35.0mm
35.0mm
40.0mm
Products:
156mm
108mm 90°
88mm
65mm
Ø54mm 350°
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
Note the power at the fuse board and the luminaire must be switched off before installation or maintenance.
· Plan the track layout and and decide accessories needed before fixing anything to the ceiling. · The maximum power per run of track is 1KW (1000W). · Ensure the ceiling is capable of holding the weight of the track and products. Take care to avoid damaging any concealed wiring and pipes.
The correct fixings should be used for brick, cavity walls or plasterboard.
· Mark the first hole position and fit the screw in position as shown.
· Feed the screw through the keyhole slot, and slide into position. Mark the position of the second hole.
· Locate the track and fit the second screw into position.
· If fitting accessories, remove the end cap, and push them firmly home. Fit extra lengths of track as required.
Connection
· The track accessories are provided with earth connection points on both sides. · When offering the accessory to the track, verify which tab needs to be removed.
(See left hand diagram). · To remove the tab, grasp firmly with a pair of pliers and lever back. · The tab should snap cleanly off. (See right hand diagram). · Locate the accessory in the track and push home.
End view of track
Remaining Earth tab needs to be inserted into Earth conductor to ensure Earth continuity.
Earth Conductor
Remove One or Other Tab Marked in Grey
Wiring
Undo the screw and remove the cover from the live end. Push out the desired cable access point. Indentify the correct cable from the supply and pull through.
N
Connect the supply wires to the terminal block, opposite
the corresponding wires from the fitting. The central
connector can also be wired in this way.
L
Refit the cover onto the live end taking care not to trap the cable.
Supply N L
Check that…
· You have correctly identified the wires.
· The connections are tight. · No loose strands have been left
out of the connection block.
Saxby Lighting - Commercial and Domestic Lighting Supplier
