ST 2×6 Game Changer Trap
Product Information
The Game Changer Trap is known as the most versatile trap on the
market. It is designed to provide effective trapping solutions for
various purposes. The trap is available in two sizes: ST 2×6 and ST
4×4.
Contact Information:
- Phone: (501) 746-0711
- Email: [email protected]
- Website: www.gamechangertraps.com
Product Usage Instructions
1. Trap Set-up
ST 2×6:
It is recommended to have two people lift and move the gates.
However, if needed, the gates can be disassembled by unpinning them
from the frame and moving them in sections. Alternatively, if a
Gate Caddy has been purchased, one person can slide panels or gates
onto the Caddy and roll them into place.
ST 4×4:
Follow the same instructions as for ST 2×6.
2. Wiring & Electronics
Refer to the accompanying wiring and electronics manual for
detailed instructions on how to set up the trap’s wiring and
electronics.
3. Quick Pin
Insert the quick pin into the designated hole on the trap’s
horizontal bar as shown in the manual.
4. Cable Tensioning
Use the provided tensioner and ratchet to tighten the cable
until it is taut.
Note: The trailer kit included with the trap is
not intended for highway use.
For additional instructions on how to set up Game Changer traps,
please visit our website: https://gamechangertraps.com/
Most Versatile Trap on the Market
Game Changer Instruction Manual
ST 2×6
ST 4×4
Contact Us: (501) 746-0711 [email protected] www.gamechangertraps.com
Ahead of the Game
Table of Contents
1 Trap Set-up…………………………………………………………………………………………….1 2 Wiring & Electronics…………………………………………………………………………….2 3 Testing Latch………………………………………………………………………………………….3 4 ST 2 & 4 Gate Cable Configuration…………………………………………………..3 5 Trapping & Moving Trap……………………………………………………………………4 6 Accessories……………………………………………………………………………………4 & 5
1 Trap Set-up
· Unstrap panels and gates from skid.
· Set-up walk-thru panel first and hinge open the door to keep the panel upright.
· Attach panels to both sides of the walkthru panel, making sure to place wire mesh to the inside of the trap.
· Attach all gates in a row to panels to make an oval shape, with the gates on the long side.
ST 2×6
ST 4×4
It is suggested two people lift and move gates. However, gates can be easily disassembled by unpinning the gate from the frame and moving it in sections. If a Gate Caddy has been purchased, one person can slide panels or gates onto the Caddy and roll into place.
1
2 Wiring & Electronics
· Set the battery box and pole directly across from the gates next to the panels.
· Attach the antenna to the top of the pole until secure.
· Mounting Camera
· Clamp camera onto the pole.
· Attach the 5′ antenna cord to the camera and antenna.
· Connect camera cord to the battery box and camera power.
· Connect gate cord to the camera and run out to the latch.
· Position the solar panel facing south and attach to the bracket located on the camera pole.
· Connect solar panel to battery box solar connection.
· Use rope and anchors provided to anchor the battery box down.
· After camera has been connected for approximately 5 minutes, it should be functioning and ready to view from app.
2
3 Testing Latch · Push latch to closed position; go to camera
app; trigger trap to drop and listen and watch for latch to open. · It is always a good practice to test the latch before gates are set every time you reset the trap. This will ensure the connection from the camera to latch is working properly and testing the latch before raising the gates minimizes the noise while out at the trap location. · Always install the latch on the furthest gate on the left when standing outside of the trap.
4 ST 2 & 4 Gate Cable Configuration · Roll out cable in front of gates starting from latch to the last gate. With eye of
cable near latch. · Connect the big eye on cable to latch.
· Run main cable (shown in red) through quick pins.
· Make sure the cable crimp is on the right side of the quick pin.
· Run leaders (shown in blue) through quick clips located in middle of gate frame.
QUICK PIN
3
· Raise the drop gates up and clip quick clip in 2×4 wire near the bottom of the drop gates.
· Make sure no cable is twisted and quick pins are straight and facing out.
5 Trapping and Moving Trap · Use Walk Gate to access inside of trap. NEVER walk under raised gates. Use the
walk gate to place bait in trap. Refer to the S.P.E.A.R. Process for proper baiting procedures. · Reverse the order of set-up to take down trap and move to another pre-bait site.
6 Accessories Anti-kick for Gate · To install, simply pull 3/8 pin and attach bracket on
horizontal bar as shown.
Cable Anti-Jump Kit · To install, first attach by looping short cables to
one side of all gates and panels. · Next, unroll the long cable and run through the
quick clips located on the short cables. · Then attach tensioner to the long cable end. · Finally, pull the slack out of the cable through the
tensioner and rachet until cable is tight.
4
ST Trailer Kit · Slide the tongue on top of skid frame
and attach by using 4 square U-bolts and brackets (3/4″ socket). · Lift skid and slide axle under skid frame up to rear middle cross member, and attach using 4 round U-bolts and brackets (3/4″ socket). · Attach tires and wheels to hubs (13/16″ socket). · Install front jack.
DISCLAIMER: TRAILER KIT IS NOT INTENDED FOR HIGHWAY USE.
For additional instructions on how to set-up Game Changer traps, visit our website. https://gamechangertraps.com/
5
Game Changer Traps | Wild Hog Traps
Game Changer Traps | Wild Hog Traps
