SP 5001 Small Gregory Lantern
Product Information:
Product Name: Small Greggory Lantern
Item Number: SP 5001
Manufacturer: Intertek
Product Certification: CM, C, US, LIST ED
Usage: Indoor Use Only (DRY)
Product Usage Instructions:
- Before installation, switch off the main electrical supply from
the main fuse box/circuit breaker. - Inspect the item carefully. If there is any damage or obvious
defect, do not install. - Remove all parts from the box.
- Install the crossbar (B) with ceiling loop (D) to the outlet
box using the mounting screws (C) provided. - Attach the glass panels (K) to the fixture body (J) and secure
them with the metal bar (L) and screws (M). - Unscrew the threaded collar on the chain end link (H) and
attach it to the top ring (I). Close the threaded collar to secure
the fixture body. - Let the canopy (E) and lock collar (F) go through the chain
(G). - Using a pair of chain pliers, shorten the chain (G) as needed
according to the fixture dimension. - Raise the fixture, unscrew the threaded collar on the other
chain end link, and attach the chain end link to the ceiling loop
(D). Close the threaded collar to secure. - Weave the power supply cord and ground wire through the chain
(G) from the top of the fixture body. - Cut the wires when you reach the canopy and ceiling loop,
making sure to leave enough length to connect inside the outlet
box. - Strip the insulation back on the two power supply wires about
5/8 inch. - Twist the power supply and ground wire together and push them
through the center hole of the ceiling loop (D). - Connect the fixture ground (bare) wire with the ground wire
from the outlet box using a wire nut (A). If your house does not
have a ground wire, attach this wire to the green grounding screw
inside the outlet box. Ensure proper grounding. - Connect the fixture neutral wire (ribbed, no markings) with the
neutral wire from the outlet box using a wire nut (A). - Connect the fixture hot (smooth edge, markings) wire with the
hot wire from the outlet box using a wire nut (A). Do not reverse
the hot and neutral connections. - Tuck these wire connections neatly into the outlet box to
secure. - Put the canopy (E) onto the ceiling loop (D) and secure it with
the lock collar (F). - Insert bulbs (not included) into the sockets.
- Installation is complete. Turn on power at the fuse or circuit
breaker.
Note: It is recommended to have this lighting
fixture installed by a licensed electrician. The item cannot be
returned once it has been installed. Carefully unpack each piece in
the top layer of packing prior to removing and retain all packing
material until inspection and installation are final.
CM
C
US
LIST ED
Intertek
DRY
Small Greggory Lantern Item # SP 5001
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING***SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT. DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. NOTE: CAREFULLY UNPACK EACH PIECE IN TOP LAYER OF PACKING PRIOR TO
REMOVING. RETAIN ALL PACKING MATERIAL UNTIL INSPECTION AND
INSTALLATION ARE FINAL.
1. Carefully remove all parts from the box. 2. Install the crossbar (B) with ceiling loop (D) to the outlet box by mounting screws (C)
provided. 3. Attach the glass panels (K) to the fixture body (J) and secure with metal bar (L) and
screws (M). 4. Unscrew the threaded collar on the chain end link (H) and attach it to the top ring (I).
Close the threaded collar to secure the fixture body. 5. Let canopy (E) and lock collar (F) go through the chain (G). 6. With the fixture dimension as a guide, shorten the chain (G) as needed using a pair of
chain pliers. 7. Unscrew the threaded collar on the other chain end link, raise the fixture then attach
chain end link to the ceiling loop (D). Close the threaded collar to secure. 8. Unwrap the wiring from the top of the fixture body. Weave the power supply cord and
the ground wire through the chain (G). 9. When you reach the canopy and ceiling loop, measure the wires then cut. Be certain
to leave enough to connect inside of the outlet box. 10. Strip the insulation back on the two power supply wires about 5/8″. 11. Twist the power supply and ground wire together and push through the center hole of
the ceiling loop (D). 12. Connect the fixture ground (bare) wire with the ground wire from the outlet box using
wire nut (A). If your house does not have ground wire, then attach this wire to the green grounding screw inside of the outlet box. IT IS IMPERATIVE THAT THIS FIXTURE BE GROUNDED.
CM
C
US
LIST ED
Intertek
DRY
Small Greggory Lantern Item # SP 5001
WE RECOMMEND INSTALLATION OF THIS LIGHTING FIXTURE BE DONE BY A LICENSED ELECTRICIAN. WARNING***SWITCH OFF THE MAIN ELECTRICAL SUPPLY FROM THE MAIN FUSE BOX/CIRCUIT BREAKER BEFORE INSTALLATION. INSPECT ITEM CAREFULLY BEFORE ATTEMPTING TO INSTALL. IF THERE IS ANY DAMAGE OR OBVIOUS DEFECT. DO NOT INSTALL. ITEM MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. NOTE: CAREFULLY UNPACK EACH PIECE IN TOP LAYER OF PACKING PRIOR TO
REMOVING. RETAIN ALL PACKING MATERIAL UNTIL INSPECTION AND
INSTALLATION ARE FINAL.
13. Connect the fixture Neutral wire (ribbed, no markings) with the neutral wire from the outlet box using wire nut (A).
14. Connect the fixture Hot (smooth edge,markings) wire with the hot wire from the outlet box using wire nut (A). DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
15. Tuck these wire connections neatly into the outlet box to secure. 16. Put canopy (E) to ceiling loop (D), and secure with lock collar (F). 17. Insert bulbs (not included) into the sockets. 18. Installation is complete, turn on power at fuse or circuit breaker.
***Clean with a dry, soft cloth only. Use no harsh abrasives or chemical agents.
