JN 5301 Alberto Small Open Cage Lantern
Product Information:
Product Name: Alberto Small Open Cage Lantern
Item Number: JN 5301
Product Description: This is a small open cage lantern light
fixture.
Product Usage Instructions:
- Carefully remove all parts from the box and place them on a
clean, soft surface. - Remove the collar loop (D) from the chain (H) by removing the
quick link (E). - Install the mounting plate (B) to the junction box and secure
it with the provided mounting screws (C). - Secure the collar loop (D) to the mounting plate (B) using
pliers to tighten the locknut. - Install the canopy (F) to the collar loop (D) and secure it
with the collar ring (G). - Determine the desired overall length and amount of chain (H)
needed. Shorten the chain using chain pliers, keeping the extra
chain for future use. - Attach the chain (H) to the collar loop (D) and fixture loop
(I) using the quick links (E). Secure the quick links (E). - Feed the wires through the hole in the frame, then hang the
cluster (K) to the hook (J) on the fixture frame. - Thread the fixture wire and ground wire through the chain (H).
When reaching the collar loop (D), ensure there is no tension on
the wires. Cut any excess wires, leaving enough to reach the
junction box. - Separate the two sides of the molded wire and strip insulation
on each end by 5/8 inch. - Loosen the collar ring (G) and carefully let the canopy (F)
slip down the chain (H). - Twist all fixture wires together and slip them through the
center hole of the collar loop (D). Untwist the wires and separate
them to prepare for connection. - Wrap the fixture ground wire (bare copper) around the green
grounding screw and tighten it. - Continue the fixture ground wire and connect it to the supply
ground wire (usually green or bare copper) using the wire nut (A).
Ensure proper grounding of the fixture. - Connect the fixture neutral wire (ribbed) to the supply neutral
wire (usually white) using the wire nut (A). - Connect the fixture hot wire (smooth with markings) to the
supply hot wire (usually black) using the wire nut (A). Be cautious
not to reverse the hot and neutral connections. - Ensure all wire connections are tight, then carefully tuck them
into the junction box. - Install the canopy (F) to the collar loop (D) and secure it
with the collar ring (G). - Install light bulbs into the sockets. Note that bulbs are not
included with the product.
Care Instructions: Clean the lantern only with
a soft dry cloth or feather duster. Avoid using abrasive or
chemical agents.
ASSEMBLY INSTRUCTIONS
Diagram 1
A B C D E F G
H
E
I
J
K Bulbs not included
Alberto Small Open Cage Lantern
Item # JN 5301
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Slip Joint Pliers
Measuring Tape
Wire Strippers
Chain Pliers Wire Cutters
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove collar loop (D) from chain (H) by removing quick link (E). 3. Install mounting plate (B) to the junction box and secure with
mounting screws (C). 4. Secure collar loop (D) to mounting plate (B) using pliers to tighten
locknut. 5. Install canopy (F) to collar loop (D) and secure with collar ring (G). 6. Determine desired overall length, and amount of chain (H) needed.
Shorten chain using chain pliers. (Keep extra chain) 7. Attach chain (H) to collar loop (D) and fixture loop (I) using quick
links (E). Secure quick links (E). 8. Feed wires through hole in frame, then hang cluster (K) to hook (J) on
fixture frame. 9. Thread fixture wire and ground wire through chain (H).
NOTE: When you reach the collar loop (D), ensure there is no tension on the wires. Cut excess wires, being sure to leave enough to reach the junction box. 10. Separate two sides of molded wire, and strip insulation on each 5/8″. 11. Loosen collar ring (G) and let canopy (F) slip down chain (H) carefully. 12. Twist all fixture wires together. Slip through center hole of collar loop (D). NOTE: Untwist wires and separate to prepare for connection.
M
LI ST ED
US
ASSEMBLY INSTRUCTIONS
Diagram 1
A B C D E F G
H
E
I
J
K Bulbs not included
Alberto Small Open Cage Lantern Item # JN 5301
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
13. Wrap fixture ground wire (bare copper) around the green grounding screw (see diagram 1). Tighten. Continue fixture ground wire and connect to supply ground wire (usually green or bare copper) using wire nut (A). NOTE: It is imperative that the fixture is grounded.
14. Connect fixture neutral wire (ribbed) to the supply neutral wire (usually white) using wire nut (A).
15. Connect fixture hot wire (smooth with markings) to the supply hot wire (usually black) using wire nut (A). CAUTION: Do not reverse the hot and neutral connections.
16. Make sure all wire connections are tight, then carefully tuck into the junction box.
17. Install canopy (F) to collar loop (D) and secure with collar ring (G). 18. Install light bulbs into the sockets.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do Not use abrasive or chemical agents.
M
LI ST ED
US
