Nvent Csbqikcl Grip Jr. Lateral Sway Brace Or Restraint Device Instruction Manual (+ PDF)

Home » Blog » Nvent Csbqikcl Grip Jr. Lateral Sway Brace Or Restraint Device Instruction Manual

Contents hide

1 CSBQIKCL Grip Jr. Lateral Sway Brace or Restraint Device

2 Product Information:

3 Product Usage Instructions:

3.1 Documents / Resources

3.1.1 References

CSBQIKCL Grip Jr. Lateral Sway Brace or Restraint Device

Product Information:

The product is a sway brace assembly designed to be installed in
accordance with NFPA-13 and the manufacturer’s installation
instructions. It is manufactured by nVent and is part of the
Dyna-Flow product line. The product is registered with various
trademarks including nVent, nVent CADDY, nVent ERICO Cadweld, nVent
ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON.

The product is intended for use in a non-corrosive indoor
environment and should only be used for the purpose it was designed
for. It is important to follow all instructions provided by nVent
to ensure proper and safe installation and performance. Failure to
do so may result in product malfunction, property damage, serious
bodily injury, and voiding of the warranty.

All load ratings provided are for static conditions and do not
account for dynamic loading such as wind, water, or seismic loads
unless otherwise noted. The customer is responsible for conforming
to all governing codes, ensuring the integrity of structures to
which the product is attached, and using appropriate
industry-standard hardware.

Appropriate safety equipment such as eye protection, hard hat,
and gloves should always be used during installation.

Product Usage Instructions:

Ensure you have the correct sway brace assembly with the
corresponding part number: CSBQIKCL0100XX, CSBQIKCL0125XX,
CSBQIKCL0150XX, or CSBQIKCL0200XX.
Identify the service pipe schedule for which the lateral 1
brace pipe will be installed.
If the service pipe schedule is N/A, no lateral 1 brace pipe is
required.
If the service pipe schedule is 10, the lateral 1 brace pipe
should be able to support a load of 655 lb (2,914 N).

Please refer to the full instruction sheet available at
www.nVent.com or from your nVent customer service representative
for more detailed installation instructions and additional
information.

View Fullscreen

INSTRUCTION SHEET

Step 1

***(XX) = Finish Specifier

Step 2

Step 3

Step 4

Sway brace assemblies are intended to be installed in accordance with NFPA-13 and the manufacturer’s installation instructions.

WARNING: 1. nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at
www.nVent.com and from your nVent customer service representative. 2. nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings. 3. All instructions must be completely followed to ensure proper and safe installation and performance. 4. Improper installation, misuse, misapplication or other failure to completely follow nVent’s instructions and warnings may cause product malfunction, property
damage, serious bodily injury and/or death, and void your warranty. 5. Products that are manufactured using spring steel components shall be used only in a non-corrosive indoor environment. 6. All pipe supports, hangers, intermediate components and structural attachments must ONLY be used as described herein and are NEVER to be used for any
other purpose.

NOTE: All load ratings are for static conditions and do not account for dynamic loading such as wind, water or seismic loads, unless otherwise noted.

The customer is responsible for: a. Conformance to all governing codes. b. The integrity of structures to which the products are attached, including their capability of safely accepting the loads imposed, as evaluated by a qualified engineer. c. Using appropriate industry standard hardware as noted above.

SAFETY INSTRUCTIONS: All governing codes and regulations and those required by the job site must be observed. Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

Dyna-Flow is a registered trademark of Allied Tube and Conduit Corporation. FM is a registered certification mark of FM Approvals LLC, LTD. NFPA is a registered trademark of National Fire Protection Association, Inc. UL is a registered trademark of UL LLC.

nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change specifications without prior notice.

TECHNICAL SUPPORT: www.nVent.com

CFS399_K

1 OF 10

INSTRUCTION SHEET

(1) Load ratings for Schedule 40 above may also be applied to GB/T 3091, EN 10255 (Heavy), and JIS G3454 pipe. (2) Load ratings for Schedule 10 above may also be applied to GB/T 3091, EN 10255 (Medium or Heavy), JIS G3452, FM approved Thinwall,
and Schedule 40 pipes unless otherwise indicated. (3) Load ratings for LW above refers to FM Approved Lightwall Pipe, commonly referred to as “Schedule 7”. These ratings may also be
applied to EN 10220, and GB/T 8163 pipe unless otherwise specified.

Part Number CSBQIKCL0100XX CSBQIKCL0125XX CSBQIKCL0150XX CSBQIKCL0200XX

UL® Loads (Listed for Restraints)

Service Pipe Schedule

Lateral 1″ Brace Pipe

Dyna-Flow®

N/A

655 lb (2,914 N)

Dyna-Flow®

655 lb (2,914 N)

Dyna-Flow®

750 lb (3,337 N)

Dyna-Flow®

750 lb (3,337 N)

1 1/4″ Brace Pipe N/A
655 lb (2,914 N) 655 lb (2,914 N) 540 lb (2,402 N) 540 lb (2,402 N) 540 lb (2,402 N) 655 lb (2,914 N) 655 lb (2,914 N) 655 lb (2,914 N) 540 lb (2,402 N) 540 lb (2,402 N) 540 lb (2,402 N)

TECHNICAL SUPPORT: www.nVent.com

CFS399_K

2 OF 10

INSTRUCTION SHEET

TECHNICAL SUPPORT: www.nVent.com

CFS399_K

3 OF 10

INSTRUCTION SHEET

Concrete anchor could be cast in place, wedge, pre-set or a concrete anchor screw.

TECHNICAL SUPPORT: www.nVent.com

CFS399_K

4 OF 10