29-CTSKK004 Skoda Steering Wheel Control Interface
Product Information:
Product Name: Skoda Steering Wheel Control Interface
Product Code: 29-CTSKK004
Vehicle Application: Skoda Yeti (5L) 2014>
Description: This product is an analogue steering wheel control
interface designed for Skoda Yeti car models. It allows you to
control various functions of your aftermarket head unit using the
buttons on your steering wheel.
Wiring Colour Codes:
- Purple – Right Rear Speaker +
- Purple/Black – Right Rear Speaker –
- Green – Left Rear Speaker +
- Green/Black – Left Rear Speaker –
- Grey – Right Front Speaker +
- Grey/Black – Right Front Speaker –
- White – Left Front Speaker +
- White/Black – Left Front Speaker –
- Yellow – Permanent 12V
- Black – Ground
- Red – Ignition 12V
Product Usage Instructions:
- Read the manual prior to installation. Ensure you have the
necessary technical knowledge for installation. - Choose a place for installation that is free of moisture and
away from heat sources. - Use the correct tools during installation to avoid damage to
the vehicle or product. - Remove and disconnect the original head unit.
- Connect the 12-way molex connector of the head unit patch lead
(supplied separately) to the interface. - Connect the opposite end of the head unit patch lead to the
head unit steering wheel control input on the back of the
aftermarket head unit. Note: This may be a 3.5mm jack plug or a
wire input depending on the head unit brand. Refer to the head unit
installation manual for further information. - Important: Complete the previous step before connecting power
to the interface to ensure steering wheel control function. - Connect the 14-way molex connector to the interface.
- Connect the male power/speaker ISO harness to the female
power/speaker ISO harness from the aftermarket head unit. For
aftermarket head units without an ISO connector, refer to the
Wiring Colour Codes on Page 2. - Connect the female vehicle-specific connectors on the harness
to the male vehicle connector from the vehicle. - Test the head unit for correct operation.
Steering Wheel Control Functionality:
| Original Button | Icon | Function |
|---|---|---|
| + | Volume + | Increase volume |
| – | Volume – | Decrease volume |
| Up Arrow | Track + | Next track |
| Down Arrow | Track – | Previous track |
| Mute Icon | Mute | Mute audio |
| Phone Button | Pick Up | Answer incoming call |
| Hang Up | Hang Up | End ongoing call |
| Window Icon | Source | Change audio source |
29-CTSSK004
Skoda Steering Wheel Control Interface
Vehicle Application Skoda Yeti (5L) 2014>
Key Features · Retains Steering Wheel Controls (if equipped)
The information provided in this document is subject to change without notice due to manufacturer changes and/or improvements to the product/s.
ABOUT THIS PRODUCT 29-CTSKK004
Analogue Steering Wheel Control Interface for Skoda Yeti car models
WIRING COLOUR CODES
Purple Purple/Black Green Green/Black Grey Grey/Black White White/Black
Right Rear Speaker + Right Rear Speaker Left Rear Speaker + Left Rear Speaker Right Front Speaker + Right Front Speaker Left Front Speaker + Left Front Speaker –
Yellow Black Red
Permanent 12V Ground Ignition 12V
PRIOR TO INSTALLATION
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be free of moisture and away from heat sources. Please ensure that the correct tools are using during the installation to avoid damage to the vehicle or product.
2
FITTING GUIDE
1. Remove and disconnect the original head unit. 2. Connect the 12 way molex connector of the head unit patch lead (supplied separately) to the interface.
3. Connect the opposite end of head unit patch lead to the head unit steering wheel control input on the back of the aftermarket head unit. NB: This may be a 3.5mm jack plug or a wire input depending upon the head unit brand being fitted. Please see the head unit installation manual for further information on where to connect. Important: This step must be completed before connecting power to the interface. Failure to so do may result in no steering wheel control function.
4. Connect the 14 way molex connector to the interface
5. Connect the male power/speaker ISO harness to the female power/speaker ISO harness from the aftermarket head unit. For aftermarket head units without an ISO connector, please refer to “Wiring Colour Codes” on Pg. 2.
3
FITTING GUIDE
6. Connect the female vehicle specific connectors on the harness to the male vehicle connector from the vehicle. Test head unit for correct operation.
STEERING WHEEL CONTROL FUNCTIONALITY
Original Button + Icon – Icon Up Arrow Down Arrow Mute Icon Phone Button Window Icon SRC
Function Volume + Volume Track + Track Mute Pick Up Hang Up Source
4
