3810-11484 Touring-to-Track Conversion Kit
Product Information:
- The AWE Exhaust System is designed for the VW MK8 GTI.
- The exhaust system is available in two versions: Touring
Edition and Track Edition. - The Touring Edition is available with Chrome Silver Tips or
Diamond Black Tips. - The Track Edition is available with Chrome Silver Tips or
Diamond Black Tips. - The exhaust system is of high build quality and craftsmanship,
and provides industry leading performance. - For up-to-date fitment information, please visit the product
page on AWE-Tuning.com.
Product Usage Instructions:
- Before disassembling your vehicle, inspect all parts of the AWE
Exhaust System. If any part is damaged or missing, contact the
place of purchase immediately. - Refer to the manufacturer’s service manual for precise torque
specifications on all OEM fasteners. - Allow adequate time for the exhaust system to cool down before
disassembly to prevent burns and injury. - Remove the OE hangers from both sides of the OE system as shown
in Figure 2. Note that these OE hangers will be used with your AWE
system. - Install the AWE inlet adapter (LG) as shown in Figure 3. Snug
the clamp but do not fully tighten it at this time. Note that the
OE sleeve clamp (A) will be reused. - Install each section and exhaust band clamps correctly to
prevent loose joints, exhaust leaks, and rattles. Refer to Figure 4
for installation instructions. - Install your AWE resonated front section (E71) by sliding a
provided clamp over the slip fit (A) and bottoming out the AWE
resonated front section on the OE inlet adapter (LG) as shown in
Figure 5-1. Next, slide the hanger bar into the OE rubber hanger
(B) as shown in Figure 5-2. Snug the clamp but do not fully tighten
it at this time.
For up-to-date fitment information, please visit the product page on AWE-Tuning.com.
3015-32658 3015-33658 3020-32658 3020-33658
AWE Touring Edition Exhaust for VW MK8 GTI – Chrome Silver Tips AWE Touring Edition Exhaust for VW MK8 GTI – Diamond Black Tips AWE Track Edition Exhaust for VW MK8 GTI – Chrome Silver Tips AWE Track Edition Exhaust for VW MK8 GTI – Diamond Black Tips
Welcome to the AWE family, and congratulations on your purchase of the AWE Exhaust System for the VW MK8 GTI. Exquisite build quality and craftsmanship, coupled with industry leading performance, distinguish this exhaust system from all others. *For up to the minute fitment information, be sure to visit the AWE website. As always, AWE Performance Specialists are standing by for any questions, right here.
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
Inspect ALL parts prior to disassembly of vehicle; If damaged or MISSING, please contact the place of purchase immediately.
Symbol
Part Number LG E71 E67 E68 E69 E70
180300 180250 3910-11012
610400 180006 180007
Description MK8 GTI OE Inlet Adapter MK8 GTI Resonated Front Section MK8 GTI Track Mid Section MK8 GTI Under Axle Pipe MK8 GTI Rear Section MK8 GTI Tip Outlet AWE Band Clamp: 3″ AWE Band Clamp: 2.5″ Clamp-kit hanger clamp kit 2 Split C-clamps and 1 Allen wrench 9/64 Rubber exhaust isolator AWE Tuning Chrome 5″ Slash Cut Tip AWE Tuning Black Chrome 5″ Slash Cut Tip
QTY 1 1 1 1 1 2 4 2 1
1 2 2
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
Inspect ALL parts prior to disassembly of vehicle; If damaged or MISSING, please contact the place of purchase immediately.
Symbol
Part Number LG E71 E66 E68 E69 E70
180300 180250 3910-11012
610400 180006 180007
Description MK8 GTI OE Inlet Adapter MK8 GTI Resonated Front Section MK8 GTI Touring Mid Section MK8 GTI Under Axle Pipe MK8 GTI Rear Section MK8 GTI Tip Outlet AWE Band Clamp: 3″ AWE Band Clamp: 2.5″ Clamp-kit hanger clamp kit 2 Split C-clamps and 1 Allen wrench 9/64 Rubber exhaust isolator AWE Tuning Chrome 5″ Slash Cut Tip AWE Tuning Black Chrome 5″ Slash Cut Tip
QTY 1 1 1 1 1 2 4 2 1
1 2 2
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
NOTE: Always refer to the manufacturer’s service manual for precise torque specifications on all OEM fasteners. CAUTION: The exhaust may be VERY HOT — allow adequate time for the system to cool down before disassembly. Severe burns and injury will occur if skin comes into contact with a hot exhaust system.
Soak all bolts and rubber hangers in penetrating oil before starting any work. 1. To begin you will need to loosen the OE clamp located at (A), enough to allow the two OE components to slide apart. 2. Remove the bolts on the under carriage protector, pull it down enough to allow you to remove the bolts holding the cross brace in shown at (B), and remove the cross brace. 3. Slide the rubber hanger off of the hanger bar, as shown at (C). 4. Unbolt the OE hangers, shown at (D). This will allow you to fully remove the factory system.
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
Remove the 2 OE hangers from both sides of the OE system as shown in Figure 2. Note: The OE hangers will be used with your AWE system.
Install the AWE inlet adapter (LG), as shown in Figure 3. Snug the clamp but do not fully tighten it at this time. Note: The OE sleeve clamp (A) will be reused, as shown in Figure 3.
It is crucial to install each section and exhaust band clamps correctly to prevent loose joints, exhaust leaks and rattles. Arrow A shows the expanded pipe and the preinstalled exhaust clamp being brought up to the corresponding pipe. Arrow B shows the overlapping pipe installed correctly over the corresponding pipe. Arrow C shows the exhaust band clamp being brought to the edge of the expanded pipe.
NOTES: · Do not fully torque any exhaust
clamp until the entire exhaust has been installed and adjusted. · Torque specification is a minimum of 60 ft/lbs
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
Install your AWE resonated front section (E71) by sliding a provided clamp over the slip fit (A) and bottoming out the AWE resonated front section on the OE inlet adapter (LG) as shown in Figure 5-1. Next slide the hanger bar into the OE rubber hanger (B) as shown in Figure 5-2. Snug the clamp but do not fully tighten it at this time.
Install the provided rubber gromet onto the OE hanger as shown at (A) in both Figure 6-1, and Figure 6-2. Next install your AWE Track mid section (E67), as shown in Figure 6-1 or your AWE Touring mid section (E66), as shown in Figure 6-2. After bottoming out the slip fit on your AWE resonated front section (E71), and sliding the hanger bar into the rubber hanger (A), snug the clamp down but do not fully tighten it.
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
Install your AWE under axle pipe (E68), slide a provided clamp over the expanded end, bottom the slip fit out on your AWE Track mid section (E67) OR AWE Touring mid section (E68). Next rotate the tube so it sits in the cut out as shown at (A) in Figure 7.
Install the OE rubber hangers on your AWE rear section (E69) as shown in Figure 8. Note: Install the OE rubber hangers on the sides they originally came off of.
Install your AWE rear section (E69) by first sliding a provided clamp over the expanded leg, then bottoming out the slip fit on your AWE under axle tube (E68), as shown at (A). Next secure the OE hangers to the car using the OE hardware, as shown at (B) in Figure 9. Repeat this process on the opposite side.
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
Install your 2 AWE tip outlets (E70) on each side of your AWE rear section (E69). Slide a provided clamp over each end of the tip outlet section, and bottom out a tip outlet on each side. Center the tip outlet in the tip cut out on the bumper and snug the clamps, as shown in Figure 10-1 and in Figure 10-2.
To install the exhaust tips with integrated clamps, first, attach the exhaust tip in the proper orientation onto the exhaust outlet tube. Insert one of the carriage bolts from the hardware kit (3910-41010) through the tab on the exhaust tip and thread on one of the corresponding nuts. Using anti-seize on the bolt threads will help installation and prevent breakage of hardware.
If exhaust system only has 2 exhaust tips while the integrated clamp kit has enough hardware for our 4 tip exhaust systems. You will have 2 sets of hardware left over that will not be used.
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
Install your AWE tips, on to the AWE tip outlets (E70), as shown in Figure 12. With your tips installed, work from the front to the rear taking time to check for proper clearance and alignment. Once the desired location positioning is achieved fully tighten all clamps. Note: Tighten all clamps to at least 60 ft/lbs.
Re-install the OE cross brace, with the OE hardware (A) that was removed in Step 1. Next secure the under carriage protector using the OE hardware, as shown at (B) in Figure 13.
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
With the complete AWE exhaust system installed, all clamps tightened and the tips aligned. It is now recommended to drive the car to allow the exhaust to heat cycle.
At this point the exhaust will be very hot, allow to cool before work continues. Check the tips for correct alignment, adjust as needed. Don’t forget to look below for any troubleshooting needs!
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
Issue Exhaust is not fitting correctly
Solution
Most fitment issues are due to improperly adjusted exhaust. This includes tip fitments and rattling due to chassis contact. Check out our fitment guide for more installation tips.
Incorrect or missing parts
Double check the parts list for your system and compare them with what you received. Fill out our contact form, found below and let us know what parts you need.
Once installed properly, your AWE exhaust will provide years of trouble-free performance.
The exhaust volume and sound will settle with usage; 800-1000 miles is required to break-in new exhaust systems.
Also, please note that the rear 180Technology® resonator has a small drain hole to allow condensation to escape. Water drops from this area are normal.
Periodic cleaning of exhaust tips is necessary to maintain proper finish, especially in areas prone to road salt and caustic deicing solutions. Use a mild soap and water solution or car wax to clean the finish. Avoid using abrasive polishes, as they can scratch the finish.
Any questions or comments, please do not hesitate to contact us:
AWE CONTACT FORM
Up-to-date warranty information is found HERE.
Copyright 2022, AWE. No part of this document may be reused or duplicated without the express permission of AWE. All rights reserved. Rev 1.1
AWE
AWE
