C0273 Estelle 24 Inch Semi Flush Mount Matte
Product Information
This product is a fixture that requires assembly and
installation. It comes with a hardware package that includes a
mounting strap unit, mounting screw, wire connector, and bolt nut.
The fixture has a fixture canopy, long rods, threaded pipes, and
sockets. It requires a maximum of 40W medium base bulbs of type
ST/Type A Vintage, which are not included in the package.
The product also comes with assembly and installation
instructions that must be followed carefully to avoid the risk of
electrical shock. Before installing, it is important to consult
local electrical codes for wiring and grounding requirements. The
product should only be serviced or installed after turning off the
power at the fuse or circuit box.
If any of the parts in the package are damaged or missing, a
spare parts list is available for re-ordering. The assembly kit
includes all necessary parts for installation.
Product Usage Instructions
- Turn off the power at the fuse or circuit box.
- Attach the mounting strap unit (A) to the outlet box using two
mounting screws (B). - Screw 11 long rods and 8-1/2 rods to the other threaded pipes
of the fixture. - Attach the fixture canopy to the mounting strap unit (A) by
inserting the fixture mounting screw, then secure it with two bolt
nuts (D). - Install 6 x 40W Max. medium base bulbs (not included). Check
relamping label at socket area or packaging for maximum wattage
allowed. - Turn on the power at the fuse or circuit box.
It is important to ensure that the maximum wattage allowed for
the bulbs is not exceeded. The relamping label at the socket area
or packaging should be checked for this information. If any of the
parts are damaged or missing, they should be re-ordered using the
spare parts list.
ASSEMBLY AND INSTALLATION INSTRUCTIONS
C0273
WARNING: TO AVOID RISK OF ELECTRICAL SHOCK, BE SURE TO SHUT OFF POWER WHILE INSTALLING OR SERVICING THIS FIXTURE.
NOTES: 1. Before installing, consult local electrical codes for wiring and grounding requirements. 2. READ AND SAVE THIS INSTRUCTION.
Hardware Package (included):
Mounting Strap Unit (A) Mounting Screw (B) Wire Connector (C) Bolt Nut (D)
Installation Steps
Turn off the power at fuse or circuit box.
1. Attach the mounting strap unit (A) to outlet box by using two mounting screws (B).
2. Screw 11″ long rods and 8-1/2″ rods to the other threaded pipes of fixture.
3. Pull out the source wires from the outlet box. Make wire connections using wire connectors (C) as follows: · Connect the hot wire (black insulation) from the fixture to the black wire from the power source. · Connect the neutral wire (white insulation) from the fixture to the white wire from the power source. · Attach the fixture ground wire (bare wire) to the mounting strap unit (A) with the green ground screw. Then, depending on local code, then connect it to the house ground wire with the wire connector (C). Carefully put all of the wires back into the outlet box.
4. Attach the fixture canopy to the mounting strap unit (A) by inserting the fixture mounting screw, then secure it with two bolt nuts (D).
5. Install 6 x 40W Max. medium base bulbs (not included). Check relamping label at socket area or packaging for maximum wattage allowed.
Fixture Canopy Fixture
Long Rod
Outlet Box House Ground Wire Wire Connector (C) Fixture Wire Green Ground Screw Mounting Strap (A) Lock Nut Fixture Mounting Screw Mounting Screw (B) Fixture Ground Wire Bolt Nut (D) Threaded Pipe
Long Rod
Socket
Rod
Max. 40W Type ST / Type A Vintage Bulb (not included)
Long Rod
Rod
Rod
Turn ont he power at fuse or circuit box.
220524
The following parts are available for re-order if damaged or missing.
Spare Parts List:
Mounting Strap Unit (A) Mounting Screw (B) Wire Connector (C)
Assembly Kit 6515MM (1 SET) Bolt Nut (D)
Rod 8-1/2″ 3345RD
Long Rod 11″ 3346RD
A B
A: 14-1/2″ B: 24-3/4″
220524
