Handi Quilter Hg01412 Lift Table Drawer Instruction Manual

HG01412 Lift Table Drawer

Product Information: Lift Table Drawer (HG01412)

The Lift Table Drawer (HG01412) is a drawer assembly designed to
be installed on a table. It provides additional storage space and
convenience for users. The drawer comes with all the necessary
parts and hardware for assembly.

Parts List:

Tools Needed:

• Part # HG01412-0101
• Part # HG01412-02
• Part # HG01412-03
• Part # HG01412-04
• Part # QM10724
• Part # QM10717
• Part # QM10348
• Part # QM10381

Product Usage Instructions: Lift Table Drawer Installation

Drawer Assembly:

1. With the help of a second person, carefully unplug the cables
   from the machine and remove it from the table.
2. Place the drawer front face on a protective surface with the
   pre-drilled holes facing up.
3. Place the pan onto the drawer face, aligning the four
   pre-drilled holes, and fasten it with four M3.5 X 8 wood screws
   using a #2 Phillips screwdriver.

Drawer Assembly – Continued:

4. Locate the Bracket-Lift Side Mount Left and Bracket-Lift Side
   Mount Right. They are mirror images of each other. Note that the
   drawer will be mounted on the opposite side from the table lift
   control switch. Screw heads go from outside of drawer towards
   inside of drawer.

   

5. Start with the outside bracket. Place a washer onto two screws
   and insert them through the two pre-drilled holes in the wooden
   table spacer, then into the threaded holes in the metal bracket.
   Start the screws by hand and then tighten them firmly with a #2
   Phillips screwdriver.
6. Repeat the process for the inside bracket.
7. Check that each bracket is straight front to back and
   perpendicular to the front table edge. Use a combination square or
   small square if needed.
8. Place the drawer pan assembly into the track by lifting the
   front of the drawer slightly and aligning it with the two brackets
   while sliding it in.
9. Check the drawer by sliding it in and out a few times to ensure
   smooth movement.
10. Screw two M3.5 X 12 wood screws into the table top at the front
    of each bracket. Note: This may be easier after carefully drilling
    a 3/32″ pilot hole. Be careful not to drill through the table
    top.

Note: Please refer to the user manual for any additional
instructions or safety precautions.

Lift Table Drawer
(HG01412)
Assembly Instructions
01/24/23

Parts List

HG-01412 Lift Table Drawer Contents

PART #

DESCRIPTION

QTY

HG01412-0101 SD DRAWER PAN ASSEMBLY W/SLIDES ATTACHED 1

HG01412-02 BRACKET-LIFT SIDE MOUNT LEFT

1

HG01412-03 BRACKET-LIFT SIDE MOUNT RIGHT

1

HG01412-04 SD LIFT FRONT FACE

1

QM10724

SCREW-#10-24 X 1.375 PHP

4

QM10717

WASHER-#10 0.688″ OD

4

QM10348

SCREW-M3.5 X 8 PHP W ZN

4

QM10381

SCREW-M3.5 X 12 PHP W ZN

4

Tools Needed:
· #2 Phillips Screwdriver – not provided · If desired drill for pre-drilling holes in top – not provided · If desired 3/32″ bit for drilling holes in top – not provided · If desired small square to check brackets – not provided

Part # HG01412-0101

Part # HG01412-02

Part # HG01412-03

Part # HG01412-04

Part # QM10724

Part # QM10717

Part # QM10348
Lift Table Drawer Installation Instructions

Part # QM10381

Page 2

Drawer Assembly
1. With the help of a second person carefully unplug the cables to the machine and remove it from the table.
2. Place the drawer front face on a protective surface with the pre-drilled holes facing up.

3. Place the pan onto the drawer face aligning the four pre-drilled holes and fasten it with four M3.5 X 8 wood screws using a #2 Phillips screwdriver.

Lift Table Drawer Installation Instructions

Page 3

Drawer Assembly – Continued

4. Locate the Bracket-Lift Side Mount Left and Bracket-Lift Side Mount Right. (They are mirror images of each other)
NOTE: The drawer will be mounted on the opposite side from the table lift control switch.
NOTE: Screw heads go from outside of drawer towards inside of drawer

Flange with two holes to outside front
HG01412-02 – LEFT BRACKET

Drawer track on inside with wheel to front

Flange with two holes to outside
front
HG01412-03 – RIGHT BRACKET

 IMPORTANT: If you have a table extension on the side where you want the drawer, the two front table extension screws will need to be removed along with the nut backing plate behind the wood table spacer. The drawer bracket will now be the nut backing plate for the screws. With someone helping support the table extension momentarily, loosen the two front screws, slide out the backing plate, slide the drawer bracket into place and tighten the two screws into the drawer bracket.
Lift Table Drawer Installation Instructions

Drawer track on inside with wheel to front
Page 4

Drawer Assembly – Continued
5. Start with the outside bracket. Place a washer onto two screws and insert them through the two predrilled holes in the wooden table spacer and then into the threaded holes in the metal bracket. Start the screws by hand and then tighten them firmly with a #2 Phillips screwdriver.
Outside Straight View

Outside Angled View
6. Repeat the process from the previous Step for the inside bracket.

Lift Table Drawer Installation Instructions

Inside Angled View

Page 5

Drawer Assembly – Continued
7. Check that each bracket is straight front to back and perpendicular to the front table edge. A combination square or small square might help with this.
8. Place the drawer pan assembly into the track by lifting the front of the drawer slightly and aligning it with the two brackets while sliding it in.
9. Check the drawer a few times by sliding the drawer in and out to ensure it moves smoothly.
10. Screw two M3.5 X 12 wood screws into the table top at the front of the bracket.
Note: This may be easier after carefully drilling a 3/32′” pilot hole. Be careful not to drill through the table top.
11. Repeat the previous Step for the front of the other bracket.

900

900

Check for straightness front to back

Lift Table Drawer Installation Instructions

Page 6