Parallel Orb Sphere Pendant Lamp
Product Information
The product is the Parallel Orb pendant light. It includes the
following components:
- (A) Lever Nut – 2 pieces
- (B) Crossbar Assembly – 1 piece
- Includes: Bushing, Crossbar, Ground Screw, Nipple, Hex Nut
- (C) J-Box Screws – 2 pieces
- (D) Canopy – 1 piece
- (E) Strain Relief – 1 piece
- (F) Orb Pendant – 1 piece
Please note that the J-Box is not included and should be
obtained separately. It is important to consult a licensed
electrician before installation to ensure correct installation and
to avoid voiding the warranty.
DANGER: ELECTRIC SHOCK RISK. Always turn off electrical power
before beginning the installation process.
Product Usage Instructions
- Thread the pendant cord through the Strain Relief (E), Canopy
(D), and Crossbar Assembly (B) in that order. Take care not to snag
the cord on these items. Adjust the cord length by tying a safety
knot as shown. If the cord is too long, cut it to the desired
length and strip the outer jacket and individual wires. Loosely
coil any extra cord inside the J-Box. - Securely fasten the Crossbar Assembly (B) to the J-Box using
the J-Box Screws (C). - Using the Lever Nuts (A), connect the pendant wires to the
120VAC power. If there is a Ground Wire present in the J-Box,
attach it to the Crossbar Assembly (B) using the green Ground
Screw. - Slide the Canopy (D) and Strain Relief (E) up to the Crossbar
Assembly (B) without snagging the cord. Thread the Strain Relief
onto the remaining length of threaded nipple until the Canopy is
flush to the ceiling and the Strain Relief is finger tight. If the
threaded nipple is too long, loosen the hex nut and thread the
nipple further up into the Crossbar Assembly, then tighten the hex
nut. - Push the pendant cord upward into the Canopy (D) slightly and
tighten the set screw in the Strain Relief (E). - Finally, restore power to the circuit.
INSTALLATION INSTRUCTIONS
Parallel Orb
J-Box (not included)
(A) Lever Nut (QTY 2)
(B) Crossbar Assembly (QTY 1)
Includes: Bushing, Crossbar, Ground Screw, Nipple, Hex Nut
(C) J-Box Screws (QTY 2)
(D) Canopy (QTY 1) (E) Strain Relief (QTY 1)
(F) Orb Pendant (QTY 1)
Please consult a licensed electrician before installation. Incorrect installation or failure to follow care instructions will void warranty.
DANGER: ELECTRIC SHOCK RISK. Turn off electrical power before beginning installation.
STEP 1
Thread pendant cord through Strain Relief (E), Canopy (D), and Crossbar Assembly (B) in that order. Be careful not to snag cord on these items. Set desired cord length by tying safety knot in cord as shown. If cord is too long, cut cord to desired length then strip outer jacket and individual wires. Loosely coil extra cord inside of J-Box.
STEP 2 Fasten Crossbar Assembly (B) to J-Box with J-Box Screws (C).
120VAC Load
120VAC Neutral
STEP 3 Using Lever Nuts (A), connect pendant wires to 120VAC power. If a Ground Wire is present in the J-Box, attach it to the Crossbar Assembly (B) using the green Ground Screw.
STEP 4
Slide Canopy (D) and Strain Relief (E) up to Crossbar Assembly (B) without snagging cord. Thread Strain Relief onto remaining length of threaded nipple until Canopy is flush to ceiling and Strain Relief is finger tight. If threaded nipple is too long, loosen hex nut and thread the threaded nipple further up into Crossbar Assembly, tightening hex nut after.
STEP 5
Push pendant cord upward into Canopy (D) slightly and tighten set screw in Strain Relief (E).
STEP 6 Return power to circuit.
