717-1-691-L LED Flush Mount
Product Information
The product is a light fixture with item numbers 717-1-691-L and
717-2-691-L. The user manual is dated August 31, 2021. The fixture
is designed to be mounted on a ceiling junction box, replacing an
old fixture. It is dimmable with ELV and/or LED compatible wall
dimmer switches. The LED module of the fixture can be replaced by a
qualified electrician without cutting wires or damaging the
decorative element.
Product Usage Instructions
- Shut off power at the fuse box or circuit breaker box before
starting the installation. - Remove the old fixture and its mounting hardware.
- Unpack the new fixture and lay out all parts in a clean
area. - Thread mounting screws into the junction box.
- Separate the fixture pan from the shade holder by loosening
screws. - Pull power supply wires out from junction box and connect black
to black, white to white, and ground wires together using wire
nuts. Wrap all wire connections with electrical tape for a more
secure connection. - Tuck all wires and connections into the outlet box.
- Place fixture pan over the junction box and slide mounting
screws through keyhole slots. Rotate fixture pan so mounting screws
slide into narrow ends of keyhole slots. Tighten mounting screws to
secure fixture pan onto ceiling. - Place shade holder over the fixture pan and tighten with
screws. - To replace the LED module, shut off power, remove shade holder,
cover, and clip, and carefully remove the LED module from fixture
pan. Reverse steps to install the new LED module. - Use a clean, soft cloth to wipe the surface of the fixture. DO
NOT use any cleaners with chemicals, solvents, or harsh
abrasives. - The fixture should be installed by a qualified electrician to
ensure proper wiring and installation.
INSTALLATION INSTRUCTIONS
Item#717-1-691-L/717-2-691-L (New. 2021-08-31) READ AND SAVE THESE INSTRUCTIONS
W AR NI N G ! SHUT P O WE R O FF AT F US E O R CI RC UI T BRE AKE R.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES FUSIBLES OU DU DISJONCTEUR. Page: 1/1
READ AND SAVE THESE INSTRUCTIONS WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT
Fig.1 Mounting screw*2
BREAKER.
AVERTISSEMENT! COUPER LE COURANT AU NIVEAU DES
FUSIBLES OU DU DISJONCTEUR.
A
PREPARATION
1. Shut off power at the fuse box or circuit breaker box and remove the old fixture including the mounting hardware.
2. Carefully unpack your new fixture and lay out all the parts in a clean area. Take care not to misplace any small parts necessary for installation.
INSTALLATION&ASSEMBLY (Fig.1)
3. Thread mounting screws (C) into junction box (not included). The length of mounting screws (C) may be adjusted if necessary.
4. Loosen screws (E) to separate fixture pan (B) from shade holder (D).
CONNECTION THE WIRES (Fig.2)
5. Pull power supply wires out from junction box. Connect black supply wire to black fixture wire and secure with wire nuts (A). Connect white supply wire to white fixture wire and secure with wire nuts (A). Connect the fixture ground wire and supply ground wire together using wire nuts (A). Wrap all wire connections with electrical tape for a more secure connection.
6. Carefully tuck all the wires and wire connections into the outlet box.
Fig.2
B
C
E D
COMPLETING THE INSTALLATION (Fig.1)
7. Place fixture pan (B) over the junction box and slide mounting screws (C) through keyhole slots. Rotate fixture pan (B) so mounting screws (C) slide into narrow ends of keyhole slots. Then tighten mounting screws (C) to secure fixture pan (B) onto ceiling.
8. Place shade holder (D) over the fixture pan (B) and tighten with screws (E).
Fig.3
Your installation is now complete. Return power and test the fixture.
Replacing LED module (Fig.3) The LED module can be replaced by a qualified electrician without cutting the wires and without damaging the decorative element to which the fixture is attached. See installation steps for more details (Fig.3)
a. Shut off the power. b. Loosen screws (E) and remove shade holder (D). c. Remove cover (H) by loosening screws (F), then loosen clip (M) on fixture pan (B) by unscrewing screws (N). Carefully remove led module from fixture pan (B). d. Reverse steps a – c for installing the new LED module.
Care and maintenance
Use a clean, soft cloth to wipe the surface of fixture. DO NOT use any cleaners with chemicals, solvents or harsh abrasives.
IMPORTANT: FIXTURE SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN TO ENSURE PROPER WIRING AND INSTALLATION.
Dimmable with ELV and/or LED compatible wall dimmer switches.
