ILG8HVLS78 HVLS Big Ceiling Fan

HVLS Big Ceiling Fan with IR Remote Control

Owner’s Manual

Models: ILG8HVLS78/ ILG8HVLS102/ ILG8HVLS120

IMPORTANT SAFETY INSTRUCTIONS

BEFORE INSTALLATION

The following components are included:

Canopy x 1
Canopy Cover x 1
Coupling Cover x 1
Motor Assembly x 1
12 Downrod x 1
Hardware installed at downrod:
- 1/4 x 1-27/32 Hex Bolt x 4
- Mounting Bracket x 1
- Hardware for bracket installation:
  - M4 Wood Screw x 2
  - 1/4 Flat washer x 4
  - 1/4 Lock washer x 4
  - 1/4 Nut x 4
  - Clevis Pin x 4
Blade x 6
Hardware for blade installation:
- 1/4 x 5/8 Screw x 19
- 1/4 Rubber washer x 19
- 1/4 Flat washer x 19
- 1/4 Nut x 19
Wire Connector x 3
AAA Battery x 1
Remote Control x 1

SPECIFICATION

Model#	Size	Voltage(V)	Frequency (Hz)	Wattage(W)	AMPS(A)	RPM	CFM	Blades	Blade Angle	Speeds	Net Weight(LBS)
ILG8HVLS78	78	120	60	74	0.92	13,200	6	10	6	23.7	ETL
ILG8HVLS102	102	120	60	78	1.2	17,800	6	10	6	25.7	ETL
ILG8HVLS120	120	120	60	78	1.2	21,000	6	10	6	26.3	ETL

INSTALLATION INSTRUCTIONS

Electrical and Structural Requirements:

1. Loosen the screws and washers installed at top of
downrod.

Route safety cable and wires through downrod. Fix the downrod to
the coupling of motor with bolt, washer, nut and tighten them
firmly then insert clevis pin.

Clamp the downrod with 2 coupling screw on coupling to prevent
shaking during operation.

2. Loosen the bolts and nuts installed at the downrod,
and save them for further installation (Step 4 & 5). Assemble
the coupling cover, canopy cover, and the canopy through
downrod.

3. Mounting bracket installation:

A. Outlet box Ceiling

Install the Mounting Bracket onto outlet box ceiling with the M4
wood screws and M4 washers.

B. Wooden Ceiling

Safety Wire must install according to instruction.

Install the Mounting Bracket onto wooden ceiling with the
1/4×1-31/32 Wood Screws.

4. Install the Hex Bolt, Flat Washer, Lock Washer, Nut
and Clevis Pin into the bottom hole on top of the
Downrod.

Note: The Hex Bolt, Flat Washer, Lock Washer, Nut and Clevis Pin
are from step 2#.

5. Insert the Hex Bolt into the upper hole on Downrod
and secure with Flat Washer, Lock Washer and Nut. Tighten the 2
bolts.

Note: Bolts must be tightened till snug.

6. Connect the wires from fan to house’s supply
wires.

7. Loosen the 2 Canopy Screws on Mounting
Bracket. Place Canopy on the Mounting Bracket. Align the
keyholes on Canopy with Mounting Bracket and secure with the 2
screws. Place the Canopy Cover on Canopy. Align the keyholes and
push in till snug.

View Fullscreen

HVLS Big Ceiling Fan with IR Remote Control Owner’s Manual
Models: ILG8HVLS78/ ILG8HVLS102/ ILG8HVLS120
PLEASE READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS
1

BEFORE INSTALLATION

Canopy x 1 Canopy Cover x 1 Coupling Cover x 1
Motor Assembly x 1

12″ Downrod x 1
Hardware installed at downrod

1/4″ x 1-27/32″

Hex Bolt

Mounting Bracket x 1
Hardware for bracket installation
M4 Wood Screw x 2

1/4″ Flat washer x 4 1/4″ Lock washer x 4 1/4″ Nut x 4 Clevis Pin x 4

M4 Washer x 2

1/4″ x 1-31/32″ Wood Screw

x 4

Blade x 6
Hardware for blade installation
1/4″ x 5/8″ Screw x 19 1/4″ Rubber washer x 19 1/4″ Flat washer x 19 1/4″ Nut x 19

Wire Connector x 3

AAA
Battery x 1
Remote Control x 1
2

Model# Size
Voltage(V) Frequency (Hz) Wattage(W)
AMPS(A) RPM CFM Blades
Blade Angle Speeds
Net Weight(LBS) Certification

SPECIFICATION

ILG8HVLS78 ILG8HVLS102

78″

102″

120

0.92

1.2

135

13,200

17,800

23.7

25.7

ETL

ILG8HVLS120 120″ 120 60 78 1.2 75 21,000 6 10 6 26.3 ETL

Dimensions(inch)

INSTALLATION INSTRUCTIONS

Electrical and Structural Requirements

Figure 1
11-7/8 in WALL
10 ft
Figure 2

CEILING JOIST

2″ x 4″

CEILING

Figure 3

OUTLET BOX (Not Included

Low profile box (Figure 3)

Deep box (Figure 4)

Deep box with brace (Figure 5)

1 Loosen the screws and washers installed
at top of downrod.
Route safety cable and wires through downrod. Fix the downrod to the coupling of motor with bolt, washer, nut and tighten them firmly then insert clevis pin.
Clamp the downrod with 2 coupling screw on coupling to prevent shaking during operaion.

Wires

Safety Cable

Downrod
Coupling Motor Housing

Coupling Screw x 2
Bolt x 2
Clevis Pin x 2 Nut x 2 Washer x 2

2 Loosen the bolts and nuts installed at the downrod,
and save them for further installation(Step 4 & 5). Assemble the coupling cover, canopy cover, and the canopy through downrod.
Canopy
Canopy Cover
Coupling Cover

3 Mounting bracket installation.
A Outlet box Ceiling

OUTLET BOX
HANGER BRACKET

Drop Roll
nting Bracket onto Outlet Boxrew must be tightened till Wire must install according to

CANOPY

Install the Mounting Bracket onto outlet box ceiling with the M4 wood screws and M4 washers.

B Wooden Ceiling
Safety Wire Install the Mounting Bracket onto wooden ceiling with the 1/4″x1-31/32″ Wood Screws

Important: Screws and Nuts must be tightened till snug. Safety Wire must install according to instruction.

4 Install the Hex Bolt, Flat Washer, Lock Washer,
Nut and Clevis Pin into the bottom hole on top of the Downrod.
Note: The Hex Bolt, Flat Washer, Lock Washer, Nut and Clevis Pin are from step 2#.

5 Insert the Hex Bolt into the upper hole on
Downrod and secure with Flat Washer, Lock
Washer and Nut.

Tighten the 2 bolts.

Important: Bolts must be tighten till snug.

6 Connect the wires from fan to
house’s supply wires.

House Supply Wires

WBhluite (N) Wire BBrolawcnk (L) Wire

Green/Yellow (E)

7 Loosen the 2 Canopy Screws on Mounting
Bracket. Place Canopy on the Mounting Bracket. Align the keyholes on Canopy with Mounting Bracket and secure with the 2 screws. Place the Canopy Cover on Canopy. Align the keyholes and push in till sung.
8 Place the Blade on top of Blade
Holder. Install Blade with the Screws provided. Important: Blade Screws must be tighten till snug. User must tighten Blade Screw yearly.
9 Below shows a complete installation diagram.

Mounting Bracket
Canopy Canopy Screws Canopy Cover
Nut Flat Washer Rubber Washer Blade Blade Holder Blade Screw

REMOTE CONTROL

Button LED LIGHT
1 2 3 4 5 6

Description Lights up when any button is pressed.
Power ON/OFF
Speed 1(Minimum)
Speed 2
Speed 3
Speed 4
Speed 5
Speed 6(Maximum) Direction Control (Clockwise/Counterclockwise)
No function No function

Forward & Reverse

Forward
Suitable for hot weather condition.

Reverse
Suitable for air-conditioned condition.
9

Wiring Diagram

Power Supply
111200-V1~20V6~06H0zHz

BLACK (HOT) WHITE (NEUTRAL)

GREEN OR BARE COPPER (GROUND)

BLACK (“AC IN L”) WHITE (“AC IN N”)

GROUND (CONNECT TO (GREEN) GROUND WIRE
ON HANGER BRACKE IF NO HOUSE GROUND WIRE EXISTS.)

23
MAINTENANCE

Warranty Information
This product comes with a 1-YEAR LIMITED COMPONENT WARRANTY. If your unit does not appear to be working properly, please contact our service center by calling 1-800-317-1688. Prior to your call, we encourage you to visit our service related website www.ilivingusa.com for troubleshooting tips and service instructions if needed.
Register your product at our website:
Or visit iLivingUSA.com/register-product
Feedback
Love it? Help us make the product more for you.
Let us know with a customer review. Please visit: https://www.amazon.com/review/review-your-purchases# At iLiving USA, we are committed to bringing top quality products to our customers.
iLIVING USA 860 Mahler Road, Burlingame, CA 94010 Tel: 1-800-317-1688 Email: [email protected]
Like us on Facebook: https://www.facebook.com/ilivingusa/ Follow us on Twitter: @iLIVINGUSA Check out our website: www.ilivingusa.com