BMW R1200 RS Fender Extender
Product Information: Product Name: Spritzschutz Product Code: Not
mentioned Manufacturer: Not mentioned Model: Not mentioned
Materials: Not mentioned Product Usage Instructions: 1.
Linsenflanschschraube / Lens head screw M5x10: – Locate the holes
on the surface where the Spritzschutz will be installed. – Insert
the Lens head screw M5x10 through the holes and tighten using a
suitable screwdriver or tool. – Apply a torque of 3.5 Nm to ensure
proper fastening. 2. U-Scheibe PA / Washer plastic M5: – Place the
plastic washer M5 onto the Lens head screw M5x10. – Ensure it is
properly aligned and sits flush against the surface. 3.
Doppelseitiges Klebeband / double-sided tape: – Peel off the
protective backing from the double-sided tape. – Apply the tape to
the desired location on the surface. – Press firmly to ensure
proper adhesion. 4. Spritzschutz / dirt trap: – Align the
Spritzschutz with the previously installed Lens head screw M5x10
and U-Scheibe PA. – Slide it onto the screw and ensure it is
securely held in place. 5. Halter rechte & linke Seite /
bracket left & right side: – Attach the bracket left &
right side to the Spritzschutz using the provided screws. – Ensure
they are tightened securely for proper support. 6.
Zylinderkopfschraube / cylinder head screw M10x90: – Locate the
holes on the surface where the Spritzschutz will be attached to the
bracket. – Insert the cylinder head screw M10x90 through the holes
on both sides of the bracket. – Tighten using a suitable
screwdriver or tool. – Apply a torque of 38.0 Nm to ensure proper
fastening. 7. U-Scheibe / Washer M: – Place the washer M onto the
cylinder head screw M10x90. – Ensure it is properly aligned and
sits flush against the bracket. Note: The above instructions
provide a general guideline for installing the Spritzschutz. Please
refer to the user manual for specific instructions related to your
product model.
Spritzschutz
Dirt trap | Piège à saletés | Trampa de suciedad | Trappola per lo sporco Art.-Nr: 44790-XXX / 44792-XXX
01 02
Zur Durchführung der Montage ist sach- und fachkundiges Wissen unabdingbar, ggf. sind auch spezielle Werkzeuge notwendig. Im Zweifel sollte die Montage von einer Fachwerkstatt durchgeführt werden.
Specialist and expert knowledge is indispensable to carry out the assembly, special tools may also be required. If in doubt, the installation should be carried out by a specialist workshop. Des connaissances techniques et spécialisées sont essentielles pour effectuer le montage, des outils spéciaux sont également nécessaires. En cas de doute, le montage doit être effectué par un atelier spécialisé.
03
04
05
Legende/Key/file Légende Anbau Tipp Fitting tip Astuce de montage Achtung Attention Attention Vergrößerung Magnification Grossissement Montagepaste Fitting lubricant Lubrifiant de montage
Schraube Screw Vis Schraubensicherung Thread locking fluid Freinfilets
M
Drehmoment Torque
Nm Torque
Reiniger Cleaner Nettoyant
Bauteil
# component composant
DE Die Farben der Abbildungen dienen nur der Veranschaulichung.
EN The colors are for illustrating purposes only. FR Les couleurs utilisées sont à titre indicatif seulement.
1 Linsenflanschschraube / Lens head screw M5x10
2 U-Scheibe PA / Washer plastic M5
3 Doppelseitiges Klebeband / double-sided tape 4 Spritzschutz / dirt trap
5 Halter rechte & linke Seite / bracket left & right side 6 Zylinderkopfschraube / cylinder head screw M10x90
7 U-Scheibe / Washer M
8 Hülse / Sleeve DØ 19,6 – dØ 10,8 – l 25,0 mm
DIN
7381A2 9021PA
912Z 125Z
ISO
7381 7093
4762 7089
Menge quantity quantité
2 2 12cm 1 2 4 8 4
Die Nr. 1 weltweit für hochwertiges BMW Motorradzubehör.
RFiadhinrgtrDiicrhetcutniogn
01
06
07
08
01
02
M5x10 3,5 Nm
M10x90 38,0 Nm
Kotflügel-Innenseite vor der Montage des Spritzschutz reinigen und entfetten.
Clean and degrease the inside of the fender before mounting the dirt trap. Nettoyez et dégraissez l`intérieur du garde-boue avant de monter le piège à saletés.
Die Nr. 1 weltweit für hochwertiges BMW Motorradzubehör.
02
