CHO 7430 Albermarle Gas Post Light
Product Information
Product: Albermarle Gas Post Light
Item: CHO 7430
Assembly Instructions
For Your Safety:
- Save these instructions for future reference.
- Please contact [email protected] for additional
information on obtaining replacement parts.
- Carefully remove all parts from the box. Place on a clean, soft
surface. - Open fixture door (C), then install glass parts (H) to fixture
(D) and secure by bending metal tabs. - Install glass part (G) to fixture door (C) and secure by
bending metal tabs, then close the door. See Diagram
1. - Connect gas tubing from lantern to gas source using proper
connection method. - Install fixture base (D) to post mount (F) and secure with
screws (E). - Double check gas connections and test for leaks before
attempting to light lantern.
Additional Hardware Included: For your
convenience, 3/8 gas adapters and additional 1/4 flare nut fitting
included inside box. Discard if not required.
Lighting Instructions
- Turn valve (A) to off position before turning on gas supply to
lantern. See Diagram 1. - Open door and allow it to completely air out.
- With lighter/flame above the burner tip (B), press in and turn
valve (A) counter-clockwise approximately 30 degrees until flame
appears. See Diagram 2. - Adjust flame to desired height. Note: Do not operate fixture
with gas valve fully open or flame height greater than 3.
Maintenance
- Keep appliance area clear and free from combustible materials,
gasoline, and other flammable vapors and liquids. - Check burner area to ensure flow of gas or combustion is never
obstructed. - Always ensure proper ventilation before use.
Care Instructions
- Allow the item to cool completely before cleaning.
- Use a feather duster or soft cloth to clean the surface.
- Use a damp towel to clean the glass.
- Avoid using abrasives or chemical agents.
ASSEMBLY INSTRUCTIONS
Albermarle Gas Post Light Item # CHO 7430
FOR YOUR SAFETY:
DANGER
FIRE OR EXPLOSION HAZARD If you smell gas: · Shut off gas to the appliance. · Extinguish any open flame. · If odor continues, leave the area immediately. · After leaving the area, call your gas supplier
or fire department. · Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or any other appliance. · Fixtures must be installed at least 3″ from combustible walls and 12″ from combustible ceilings. · Installation must conform with local codes or, in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1. Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.
Save these instructions for future reference.
Please contact [email protected] for additional information on obtaining replacement parts.
ASSEMBLY INSTRUCTIONS
G (1 pc)
D C
E 3″
F Post mount not included
H (3 pcs)
Albermarle Gas Post Light
Item # CHO 7430
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Open fixture door (C), then install glass parts (H) to fixture (D) and
secure by bending metal tabs. 3. Install glass part (G) to fixture door (C) and secure by bending
metal tabs, then close the door. See diagram 1. 4. Connect gas tubing from lantern to gas source using proper
connection method. 5. Install fixture base (D) to post mount (F) and secure with screws (E). 6. Double check gas connections and test for leaks before attempting to
light lantern.
ADDITIONAL HARDWARE INCLUDED: For your convenience, 3/8″ gas adapters and additional 1/4″ flare nut fitting included inside box. Discard if not required.
ASSEMBLY INSTRUCTIONS
B A
Diagram 1
B
A Diagram 2
LIGHTING YOUR LANTERN
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
LIGHTING YOUR LANTERN 1. Turn valve (A) to off position before turning on gas supply to lantern.
See diagram 1. 2. Open door and allow to completely air out. 3. With lighter/flame above the burner tip (B), press in and turn valve (A)
counter-clockwise approximately 30 degrees until flame appears. See diagram 2. 4. Adjust flame to desired height. Note: Do not operate fixture with gas valve fully open or flame height greater than 3″.
MAINTENANCE: CHECK BEFORE EVERY USE 1. Keep appliance area clear and free from combustible materials,
gasoline and other flammable vapors and liquids. 2. Check burner area to ensure flow of gas or combustion is never
obstructed. 3. Always ensure proper ventilation before use.
CARE INSTRUCTION 1. Allow for item to cool completely before cleaning. 2. Use feather duster or soft cloth to clean surface. 3. Use damp towel to clean glass. 4. No abrasives or chemical agents.
