Visual Comfort Cho 2560 Fresno Medium Bracketed Gas Wall Lantern Instruction Manual

CHO 2560 Fresno Medium Bracketed Gas Wall Lantern

Product Information: Fresno Medium Bracketed Gas Wall
Lantern

Item Number: CHO 2560

Manufacturer: Visual Comfort

Product Type: Gas Wall Lantern

Assembly Instructions

1. Carefully remove all parts from the box. Place on a clean, soft
   surface.
2. Remove mounting plate (C) from fixture (E) by removing screws
   (F).
3. Using mounting plate (C) as a guide, mark mounting hardware
   positions and follow mounting hardware instructions to secure
   mounting plate to wall surface.
4. Open fixture door (I), then install glass parts (H) to fixture
   (E) and secure by bending metal tabs.
5. Install glass part (G) to door (I) and secure by bending metal
   tabs, then close the door.
6. Connect gas tubing (D) from lantern to gas source using proper
   connection method.
7. Install fixture (E) to mounting plate (C) and secure with
   screws (F).
8. Double check gas connections and test for leaks before
   attempting to light lantern.

Note: This light fixture should be installed in
accordance with all applicable, local installation codes, and by a
person familiar with the construction and operation of it, as well
as the hazards involved. Inspect the item and contents carefully.
If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.

Tools Required (Not Included):

• Phillips Screwdriver
• Slotted Screwdriver
• Drill
• Pencil
• Hammer

Additional Hardware Included: For your
convenience, 3/8 gas adapters and additional 1/4 flare nut fitting
are included inside the box. Discard if not required.

Lighting Your Lantern

Note: This light fixture should be installed in
accordance with all applicable, local installation codes, and by a
person familiar with the construction and operation of it, as well
as the hazards involved. Inspect the item and contents carefully.
If any damage or defect is found, do not install. Retain all
packaging material until installation is complete and approved.

1. Turn valve (A) to off position before turning on the gas supply
   to the lantern. See Diagram 1.
2. Open the door and allow it to completely air out.
3. With a lighter/flame above the burner tip (B), press in and
   turn valve (A) counter-clockwise approximately 30 degrees until the
   flame appears. See Diagram 2.
4. Adjust the flame to the desired height. Note: Do not operate
   the fixture with the gas valve fully open or flame height greater
   than 3.

Maintenance: Check Before Every Use

1. Keep the appliance area clear and free from combustible
   materials, gasoline, and other flammable vapors and liquids.
2. Check the burner area to ensure the flow of gas or combustion
   is never obstructed.
3. Always ensure proper ventilation before use.

Care Instructions

1. Allow the item to cool completely before cleaning.
2. Use a feather duster or soft cloth to clean the surface.
3. Use a damp towel to clean the glass.
4. Avoid using abrasives or chemical agents.

ASSEMBLY INSTRUCTIONS

Fresno Medium Bracketed Gas Wall Lantern
Item # CHO 2560
FOR YOUR SAFETY:
DANGER
FIRE OR EXPLOSION HAZARD If you smell gas: · Shut off gas to the appliance. · Extinguish any open flame. · If odor continues, leave the area immediately. · After leaving the area, call your gas supplier
or fire department. · Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or any other appliance. · Fixtures must be installed at least 3″ from combustible walls and 12″ from combustible ceilings. · Installation must conform with local codes or, in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1. Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.
Save these instructions for future reference.
Please contact [email protected] for additional information on obtaining replacement parts.

ASSEMBLY INSTRUCTIONS

G (1pcs)

H (3pcs)

Fresno Medium Bracketed Gas Wall Lantern
Item # CHO 2560
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.

TOOLS REQUIRED (NOT INCLUDED):

D

Phillips Screwdriver

Slotted Screwdriver

Drill

Pencil

Hammer

C

1. Carefully remove all parts from the box. Place on a clean, soft surface.

2. Remove mounting plate (C) from fixture (E) by removing screws (F).

3. Using mounting plate (C) as a guide, mark mounting hardware

positions and follow mounting hardware instructions to secure

F

mounting plate to wall surface.

Note: Due to various mounting surface types, mounting hardware is

not included. Please select proper hardware based on surface

E

application.

4. Open fixture door (I), then install glass parts (H) to fixture (E) and

I

secure by bending metal tabs.

5. Install glass part (G) to door (I) and secure by bending metal tabs,

then close the door.

6. Connect gas tubing (D) from lantern to gas source using proper

connection method.

7. Install fixture (E) to mounting plate (C) and secure with screws (F).

8. Double check gas connections and test for leaks before attempting to

light lantern.

ADDITIONAL HARDWARE INCLUDED: For your convenience, 3/8″ gas adapters and additional 1/4″ flare nut fitting included inside box. Discard if not required.

ASSEMBLY INSTRUCTIONS
B A
Diagram 1

B
A Diagram 2

LIGHTING YOUR LANTERN
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
LIGHTING YOUR LANTERN 1. Turn valve (A) to off position before turning on gas supply to lantern.
See diagram 1. 2. Open door and allow to completely air out. 3. With lighter/flame above the burner tip (B), press in and turn valve (A)
counter-clockwise approximately 30 degrees until flame appears. See diagram 2. 4. Adjust flame to desired height. Note: Do not operate fixture with gas valve fully open or flame height greater than 3″.
MAINTENANCE: CHECK BEFORE EVERY USE 1. Keep appliance area clear and free from combustible materials,
gasoline and other flammable vapors and liquids. 2. Check burner area to ensure flow of gas or combustion is never
obstructed. 3. Always ensure proper ventilation before use.
CARE INSTRUCTION 1. Allow for item to cool completely before cleaning. 2. Use feather duster or soft cloth to clean surface. 3. Use damp towel to clean glass. 4. No abrasives or chemical agents.