CHO 2550 Fresno Medium 3 4 Gas Wall Lantern
Product Information
Product Name: Fresno Medium 3/4 Gas Wall
Lantern
Item Number: CHO 2550
Product Safety:
Please save these assembly instructions for future reference. If
you need any additional information or replacement parts, please
contact [email protected].
Notice:
This light fixture should be installed according to local
installation codes and by someone familiar with its construction
and operation. Inspect the item and its contents carefully. If any
damage or defect is found, do not install. Keep all packaging
material until installation is complete and approved.
Tools Required (Not Included):
- Phillips Screwdriver
- Slotted Screwdriver
- Drill
- Pencil
- Hammer
Assembly Instructions
- Remove all parts from the box and place them on a clean, soft
surface. - Detach the mounting plate (C) from the fixture (E) by removing
screws (F). - Use the mounting plate (C) as a guide to mark the mounting
hardware.
Additional Hardware Included:
For your convenience, the box contains 3/8 gas adapters and an
additional 1/4 flare nut fitting. Discard if not required.
Lighting Your Lantern
Notice:
This light fixture should be installed according to local
installation codes and by someone familiar with its construction
and operation. Inspect the item and its contents carefully. If any
damage or defect is found, do not install. Keep all packaging
material until installation is complete and approved.
- Turn valve (A) to the off position before turning on the gas
supply to the lantern. Refer to Diagram 2. - Open the door and allow it to completely air out.
- With a lighter or flame above the burner tip (B), press in and
turn valve (A) counterclockwise approximately 30 degrees until the
flame appears. Refer to Diagram 3. - Adjust the flame to the desired height. Note: Do not operate
the fixture with the gas valve fully open or with a flame height
greater than 3.
Maintenance
Check Before Every Use:
- Ensure the appliance area is clear and free from combustible
materials, gasoline, and other flammable vapors and liquids. - Check the burner area to ensure that the flow of gas or
combustion is never obstructed. - Always ensure proper ventilation before use.
Care Instructions
- Allow the item to cool completely before cleaning.
- Use a feather duster or a soft cloth to clean the surface.
- Use a damp towel to clean the glass.
- Avoid using abrasives or chemical agents.
ASSEMBLY INSTRUCTIONS
Fresno Medium 3/4 Gas Wall Lantern
Item # CHO 2550
FOR YOUR SAFETY:
DANGER
FIRE OR EXPLOSION HAZARD If you smell gas: · Shut off gas to the appliance. · Extinguish any open flame. · If odor continues, leave the area immediately. · After leaving the area, call your gas supplier
or fire department. · Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of this or any other appliance. · Fixtures must be installed at least 3″ from combustible walls and 12″ from combustible ceilings. · Installation must conform with local codes or, in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1. Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.
Save these instructions for future reference.
Please contact [email protected] for additional information on obtaining replacement parts.
ASSEMBLY INSTRUCTIONS
D C
F E I
G (1pcs)
H (2pcs)
Diagram 1
Fresno Medium 3/4 Gas Wall Lantern
Item # CHO 2550
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
TOOLS REQUIRED (NOT INCLUDED):
Phillips Screwdriver
Slotted Screwdriver
Drill
Pencil
Hammer
1. Carefully remove all parts from the box. Place on a clean, soft surface. 2. Remove mounting plate (C) from fixture (E) by removing screws (F). 3. Using mounting plate (C) as a guide, mark mounting hardware
positions and follow mounting hardware instructions to secure mounting plate to wall surface. Note: Due to various mounting surface types, mounting hardware is not included. Please select proper hardware based on surface application. 4. Open fixture door (I), then install glass parts (H) to fixture (E) and secure by bending metal tabs. 5. Install glass part (G) to door (I) and secure by bending metal tabs, then close the door. 6. Connect gas tubing (D) from lantern to gas source using proper connection method. Note: If gas tubing cannot be connected behind back plate, remove grommet from bottom of back plate for alternate exit location. See diagram 1. 7. Install fixture (E) to mounting plate (C) and secure with screws (F). 8. Double check gas connections and test for leaks before attempting to light lantern.
ADDITIONAL HARDWARE INCLUDED: For your convenience, 3/8″ gas adapters and additional 1/4″ flare nut fitting included inside box. Discard if not required.
ASSEMBLY INSTRUCTIONS
B A
Diagram 2
B
A Diagram 3
LIGHTING YOUR LANTERN
NOTICE: This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect item and contents carefully. If any damage or defect is found, do not install. Retain all packaging material until installation is complete and approved.
LIGHTING YOUR LANTERN 1. Turn valve (A) to off position before turning on gas supply to lantern.
See diagram 2. 2. Open door and allow to completely air out. 3. With lighter/flame above the burner tip (B), press in and turn valve (A)
counter-clockwise approximately 30 degrees until flame appears. See diagram 3. 4. Adjust flame to desired height. Note: Do not operate fixture with gas valve fully open or flame height greater than 3″.
MAINTENANCE: CHECK BEFORE EVERY USE 1. Keep appliance area clear and free from combustible materials,
gasoline and other flammable vapors and liquids. 2. Check burner area to ensure flow of gas or combustion is never
obstructed. 3. Always ensure proper ventilation before use.
CARE INSTRUCTION 1. Allow for item to cool completely before cleaning. 2. Use feather duster or soft cloth to clean surface. 3. Use damp towel to clean glass. 4. No abrasives or chemical agents.
