ME-150DH Hand Held Crimp Sealer
Product Information: Hand Held Crimp Sealers 150DH
The Hand Held Crimp Sealers 150DH is a manual sealing device
used for sealing various materials such as Cellophane, Wax Paper,
Foils, Alluminium-Laminates and Heat Seal-able Labels. It is
equipped with temperature controller, working light, and covered
two 12 mm wide heated Jaws for constant heat. The Seal Jaws are
PTFE coated and produce vertical line embossed seals. It has a
power cord length of 3.0 meter and an aluminum mesh safety
guard.
Safety Advice:
To prevent damage to the device and injuries to the operator, it
is necessary to comply with the safety notes in the manual. The
mentioned warnings describe possible injuries and damages that are
due to wrong usage or maintenance of the device. Please read and
follow these safety notes before reading the manual.
- CAUTION: To reduce the risk of shock, disconnect the unit from
the supply circuit before servicing the replacement of the heating
element. - WARNING: A live heating element is located in the jaw under the
PTFE cloth. Use caution during operation. DO NOT TOUCH THE
ELEMENT! - For continued protection against fire or electric shock,
replace only with type cartridge and suitable ampere fuse, provided
in legible adjacent to fuse holder. - Close supervision is required when the product is used near
children.
Helpful Information:
- Always keep the sealing platform clean. Particular care should
be taken to remove any residue from the Seal Jaws. - Do not clean the sealing platform with anything wet.
- Occasionally check the condition of both sides of the heater
jaws. Poor sealer platform will affect the quality of your
seal. - Never touch the heater jaws for high temperature.
- USE ONLY GENUINE REPLACEMENT PARTS.
Construction Diagram and Parts List:
The Hand Held Crimp Sealers 150DH consists of Upper Lever Body,
Lower Lever Body, Upper Sealer Jaw, Ceramic Pads, Clips for Sealer
Jaw, Bolt Pin & Screw, Power Indication Lamp, Temp. Controller
& Switch, Heater, Return Spring, Power Plug, Fixed Plates for
Heater, Metal Plate for Protection, Sealer PTFE Cloth, Sealer
Rubber, Rubber Holder, Lead Wire, and Fiber Washer.
Operating Instructions:
- Connect the device to a properly grounded outlet only.
- Turn on the device and wait for it to heat up to the desired
temperature. - Place the material to be sealed between the Seal Jaws and close
the Upper Lever Body onto the Lower Lever Body. - Hold the Upper Lever Body down firmly until the seal is
complete. - Release the Upper Lever Body and remove the sealed material
from the Seal Jaws. - Repeat the process for additional seals.
+++++++ Complete Manual – English +++++++
150DH
Hand held crimp sealers Manual
Content, safety advice & helpful information
Please read before use Thank you for purchasing the hand held crimp sealer 150DH. Please read this instruction carefully before use. Please keep this manual on file as reference book and for troubleshooting.
Content Safety advice & helpful information …………… S. 3 Construction diagram ………………………………. S. 4 Parts list ……………………………………………………S. 5 Benefits & electric connection diagram ………S. 7 Operating instructions ……………………………….S. 8
2
Safety advice
To prevent damage of the device and inju- ries of the operator, it is absolutely neces- sary to comply the safety notes in this manual.
The mentioned warnings describe possible injuries and damages, which are due to wrong usage or maintenance of the device.
Please read and follow these safety notes before reading the manual.
CAUTION:
WARNING:
1) To reduce the risk of shock, disconnect the unit from the supply circuit before servicing the replacement of the heating element.
1) A live heating element is located in the jaw under the PTFE cloth. Use caution during operation. DO NOT TOUCH THE ELEMENT!
2) To provide continued protection against risk of electric shock, connect to properly grounded outlet only.
3) If the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufac ture or its service agent.
2) For continued protection against fire or electric shock, replace only with type cartridge and suitable ampere fuse, provided in legible adjacent to fuse holder.
3) Close supervision is required when the product is used near children.
Helpful information
1) Always keep the sealing platform clean. Particular care ,,should” be taken to remove any redidue from the Seal Jaws.
2) Do not clean the sealing platform with anything wet.
3) Occasionally check the condition both sides of the heater jaws. a poor sealer platform will effect the quality of your seal.
4) Never touch to heater jaws for high temperature.
5) USE ONLY GENUINE REPLACEMENT PARTS.
3
Construction diagram and parts list
Construction diagram
7 1
5
12
13 18
11
9
3
14
4 68
15
10
16
2 17
4
Parts list
No Description
1 Upper Lever Body
2 Lower Lever Body
3 Upper Sealer Jaw
4 Ceramic Pads
5 Clips for Sealer Jaw
6 Bolt Pin & Screw
7 Power Indication Lamp
8 Temp. Controller & Switch
9 Heater
PartsNo
1A107006
1A107007
2B407001
1J407001
1C407005
1D207005
1E407005
1E607005
1E607005
No Description
10 Return Spring
11 Power Plug
12 Fixed Plates for Heater
13 Metal Plate for Protection
14 Sealer PTFE Cloth
15 Sealer Rubber
16 Rubber Holder
17 Lead Wire
18 Fiber Washer
PartsNo
1E107005
1E301005
1C407006
1C107004
1J503115
1G201010
1C107005
1E307002
1J307002
5
Benefits, electric connection diagram and operating instructions
Benefits 1) constant heat for Cellophane & Foil 2) covered two 12 mm wide heated Jaws for Cellophane, Wax Paper, Foils, Alluminium-
Laminates and Heat Seal-able Labels. 3) light weight and easy to grip 4) equipped with temperature controller and working light 5) PTFE coated Seal Jaws 6) vertical line embossed seal 7) the power cord length is 3.0 meter 8) aluminium mesh safety guard
Elektronischer Schaltplan
Operating instructions
1) Connect power supply plug to AC outlet, the Power light appears indicating power to the unit.
2) Turn on main temperature knob. Heating light appears, adjust the temp. control knob to the 100°C suitable scale fo thickness and material of bag. The heating light will go off about three minutes, it is the heating time.
3) Adjust the temperature knob to suitable scale for sealing material.
4) Insert bag into the seal jaws and apply squeeze the lever handle to seal the bag.
5) Release the handle and remove the sealed bag.
6) If it does no complete with the seal, turn the temp. knob add until you get desired seal.
7) Turn off machine when not in use. Allow the sealer to cool down for 10 minutes before storing.
The temperature controller is calibrated in centigrade to convert to fathrenheit. (°Cx8/5 +32=°F) For safety keep hands and fingers away from the jaws or hex nuts.
6
7
