Acura TLX 15-17 Front Splitter
Product Information
The product is a lip spoiler that can be attached to the front
bumper of a vehicle. The assembly instructions include a parts list
and information on the tools required for installation. The product
comes with bolts, lock nuts, finish washers, and spacers of various
sizes. The parts list may differ according to the specific model of
the vehicle.
Product Usage Instructions
Tools Required: Car jack and jack stands,
permanent marker, drill, drill bits (5/16), hardware bag
(included), Torx, Phillips, 10mm box (to remove splash guard if
necessary).
Caution: Professional installation is strongly
recommended.
- Jack the front of the car and use jack stands for easy access
to the front bumper. - Align the lip spoiler with the OEM holes on the front bumper.
The tip of the lip should be lined with the corner of the bumper
near the wheel. Use the provided screws to attach the lip spoiler
to the bumper. - Use a permanent marker to mark the drill spots on the bumper
through the holes in the lip spoiler. - Remove the lip spoiler and drill holes in the marked spots on
the bumper. - Attach the lip spoiler to the bumper using the provided bolts,
lock nuts, finish washers, and spacers of various sizes. Use the M8
hex key and M6 hex key to install the bolts.
Note: The parts list may differ according to your specific
vehicle model.
Align with OEM holes, use provided screws. Align with OEM holes, use provided screws.
ACURA TLX 15-17 · FRONT SPLITTER A-SPEC MODEL
ASSEMBLY INSTRUCTIONS
1/2″
1/2″
5/8″ 1-1/2″
5/8″ 1-1/2″
45mm M6
40mm M8
SPACERS SIDE VIEW
1-1/2″ Front of the vehicle
40mm M8
45mm M6
55mm M8
55mm M8
PARTS LIST MAY DIFFER ACCORDING TO YOUR MODEL
PARTS LIST
40mm M8 Bolts x 2 55mm M8 Bolts x 2
M8 Lock Nuts x 4
* Install your bolt with your hex key by the bottom of your lip
45mm M6 Bolts x 2 M6 Finish Washers x 2
5/8″ Round Spacers x 2 1/2″ Round Spacers x 2 1-1/2″ Spacers x 2 M8 Hex Key x 1 M6 Hex Key x 1
YOUR LOYALTY AS A CUSTOMER IS GREATLY APPRECIATED – © 2022 ARTWORK BODYSHOP
ACURA TLX 15-17 · FRONT SPLITTER A-SPEC MODEL
INSTALLATION INSTRUCTIONS
TOOLS REQUIRED
CAR JACK & JACK STANDS PERMANENT MARKER DRILL DRILL BITS 5/16 HARDWARE BAG (INCLUDED) TORX, PHILLIPS, 10MM BOX
(TO REMOVE YOUR SPLASH GUARD, IF NECESSARY)
**CAUTION: PROFESSIONAL INSTALLATION IS STRONGLY RECOMMANDED** 1. Jack the front of the car for an easy access (don’t forget to put your jack stands). 2. Align perfectly the lip under the bumper (the tip of the lip should be lined with the
corner of your bumper near the wheel, see picture above). 3. With the permanent marker, mark the drill spot on the bumper through the holes
of the lip (the lip should not move if you can’t reach the bumper with your marker, skip to step #4). 4. Drill in the middle of your marks (or holes) with 5/16 drill bit. 5. Make an easy access to reach the holes inside the bumper. 6. Assemble the lip with hardware (see assembly instructions). 7. Put the lip on the bumper by aligning the bolts through the holes. 8. Thight all the remaining hardware inside the bumper (nuts & washers), while holding your hex key into the bolt to make sure it won’t turn. 9. Reinstall all removed trims and you’re ready to rock n roll. Take pictures and send them to [email protected] and don’t forget to tag us on social media @artworkbodyshop.
YOUR LOYALTY AS A CUSTOMER IS GREATLY APPRECIATED – © 2022 ARTWORK BODYSHOP
