76382-QC Flush Mount Ceiling Light
Product Information:
The product is a light fixture that consists of several parts
including a fixture, glass shade, cage, threaded pipe and hex nut,
hex nuts A, washer, rubber ring, cap, decorative nut, mounting
screws, mounting unit, wire nuts, and assembly instructions. The
product requires tools such as a ladder, safety glasses, electrical
Phillips screwdriver, flat blade screwdriver, pliers, wire
strippers, and tape for assembly. The product is designed to be
attached to a junction box and connected to the electrical wiring
in a building to provide lighting.
Product Usage Instructions:
- Use the mounting screws to attach the mounting unit to the
junction box. - Make the electrical connection from the junction box to the
fixture. Connect the ground wire to the mounting unit using the
preinstalled green ground screw. Then, connect the positive,
negative and ground wires with the supplied wire nuts. Secure with
electrical tape. - Attach the fixture to the mounting unit by inserting two
fixture screws and rotating the fixture until it locks in place.
Then tighten the fixture screws securely. - Screw the threaded pipe and hex nut into the fixture, then
secure it with hex nut. - Remove the two hex nuts A, washer and rubber ring from the
threaded pipe and hex nut. Place the glass shade, rubber ring and
washer onto the threaded pipe and hex nut, then secure with hex nut
A. - Place the cage onto the threaded pipe and hex nut, then secure
with hex nut A. - Place the cap onto the threaded pipe and hex nut, then secure
with decorative nut. - Install bulb (not included).
Note: The product comes with hardware included, but parts shown
may differ slightly per light fixture. Additionally, sealing tape
is not included in the package.
ASSEMBLY INSTRUCTIONS
CAUTION
³Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have resulted during shipping. If there is a defect in the wire, do not attempt installation.
TOOLS REQUIRED
³Before starting installation of this fixture or removal of a previous fixture, disconnect the power by turning off the circuit breaker or by
removing the fuse at the fuse box.
Ladder
Safety glasses
Electrical Phillips
tape
screwdriver
Flat blade screwdriver
Pliers
Wire strippers
HARDWARE INCLUDED
Fixture
Glass Shade
Cage
Threaded Pipe and Hex Nut
Hex Nuts A
Washer
Rubber Ring
Cap
Decorative Nut
Mounting Screws
Mounting Unit Wire Nuts
*PARTS SHOWN MAY DIFFER SLIGHTLY PER LIGHT FIXTURE
EXPLODED PARTS
Wire Nuts
Mounting Unit
INSTALLATION STEP 1
Use the mounting screws to attach the mounting unit to the junction box.
Mounting Screws
Fixture
Bulbs (not included) Threaded Pipe and Hex Nut Glass Shade
Rubber Ring Washer
Hex Nuts A
Cage
Hex Nuts A Cap Decorative Nut
ASSEMBLY INSTRUCTIONS INSTALLATION
STEP 2
Make the electrical connection from the junction box to the fixture. Connect the ground wire to the mounting unit using the preinstalled green ground screw. Then, connect the positive, negative and ground wires with the supplied wire nuts. Secure with electrical tape.
Black or Red wire (hot) from the junction box
White wire (neutral) from the junction box
Black wire from the fixture
White wire from the fixture
Bare or Green ground wire from the junction box
Ground wire from the Fixture
*Green Ground Screw
*Sealing tape (not included)
STEP 3
Attach the fixture to the mounting unit by inserting two fixture screws and rotating the fixture until it locks in place. Then tighten the fixture screws securely.
STEP 4
STEP 5
Screw the threaded pipe and hex nut into Install bulb (not included)
the fixture, then secure it with hex nut.
STEP 6
1. Remove the two hex nuts A ,washer and rubber ring from the threaded pipe and hex nut.
2.Place the glass shade, rubber ring and washer onto the threaded pipe and hex nut, then secure with hex nut A.
STEP 7
Place the cage onto the threaded pipe and hex nut,
then secure with hex nut A.
STEP 8
Place the cap onto the threaded pipe and hex nut,
then secure with decorative nut.
