Techni Mobili Rta-913d Home Office Workstation With Storage Instruction Manual

RTA-913D Home Office Workstation with Storage

Product Information: RTA-913D

This is a ready-to-assemble product with the following main
parts:

• Main panel x1
• Left panel x1
• Back-Left panel x1
• Middle panel x1
• Lower panel x1
• Right panel x1
• Top front panel x1
• Drawer front panel x1
• Drawer right panel x2
• Drawer left panel x2
• Drawer back panel x2
• Drawer bottom panel x2
• Back-Right panel x1

The product comes with hardware, screws, and fittings as listed
below:

This product uses cam bolts and locks. Follow the instructions
below to use them:

1. Screw the bolt into the corresponding hole on panel A.
2. Join panel B to panel A. If panel B comes with the cam lock
   pre-installed, make sure it is aligned to receive the bolt’s head
   (refer to point 3). There might be a very small gap between the
   panels which is normal.
3. Insert the cam lock on panel B making sure it goes aligned to
   receive the bolt’s head.
4. Turn the cam lock clockwise. This will lock the parts together
   and will close any gaps.

Note: You will need a Phillips screwdriver and
mallet/hammer (not included) for the assembly.

Product Usage Instructions: RTA-913D

Before starting the assembly, read and follow these tips and
warnings:

• Do a quick inventory to make sure all parts and hardware are
  present.
• To avoid misalignments, leave the screws loose and tighten them
  only when all pieces are positioned correctly.
• If you find any missing, damaged, or defective parts, refer to
  the last pages of the manual for replacement instructions.
  Replacement service is limited to the 48 contiguous United
  States.
• If you need assistance during assembly, contact customer
  service.
• Read and analyze the instructions and illustrations thoroughly
  before proceeding with each step.
• Make sure you use the correct hardware for each step. Using the
  wrong size of screw, bolt, or pin might strip the threads or cause
  damage to the part.
• Do not overtighten or force the screws as they might break,
  strip, damage the threads of the holes or get stuck inside the
  part.
• If the laminate covers the hole on a panel, pass and press the
  tip of your finger over the area where the hole should be located
  to feel the indentation, and once found, carefully pierce the
  laminate to reveal the hole underneath.

Refer to the main parts layout on page 3 for reference during
assembly.

REV.NTL-6611-0322-1

P.1

RTA-913D

P. 1

· Please read carefully the assembly instructions before the installation.
· Do not discard this manual or any of the packaging material until the unit has been completely assembled.
· Might require two people.
SAMPLE ­ DO NOT SCAN
· We have added QR Codes to some steps for your assistance. If a QR code is provided on a step, scan it to view the assembly video online.

P.2
1 Main panel
x1

RTA -913D
MAIN PARTS LIST
2 Left panel
x1

P.2
3 Back-Left panel
x1

4 Middle panel
x1

5 Lower panel
x1

6 Right panel
x1

7 Top front panel
x1

8 Drawer front panel 9 Drawer right panel 10 Drawer left panel 11 Drawer back panel

x2

x2

x2

x2

12 Drawer bottom
x2 panel

13 Back-Right panel
x1

P.3

RTA -913D

P.3

LIST OF HARDWARE, SCREWS AND FITTINGS

PART QTY
A 10 B 14 C 14 D8 E4

ITEM
M6x30
Wooden dowels
M5x31
Bolts
M12x9
Cam locks
ST3.5×40
(Flanged head)
ST3.5×40
(Flat head)

F 4 ST3.5×25

G 16 ST4x12

PART QTY
I 14 J 40 K6 L2 M1 N4

ITEM
15mm plastic
adhesive covers
M4x23
nails
12x12x6mm
Nail-in glide stud
128mm Handle
Touch-Up
15x15x40mm
Angle bracket

H 16 ST3x12

O

2
Set

Sliders

NOTE: You will need for the assembly a Phillips screwdriver and mallet/hammer (not included).

MAIN PARTS LAYOUT (FOR REFERENCE):

10 9

P.4

RTA-913D

P. 4

This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing the
assembly using this kind of hardware.

Cam Lock

Cam Bolt

1. Screw the bolt into the corresponding hole on panel “A”.

2. Join panel “B” to panel “A”. If panel “B” comes with the cam lock pre-installed, make sure it is aligned to receive the bolt’s head (refer to point 3). There might be a very small gap between the panels which is normal.

Panel “B”

Panel “B”

Panel “B”

3. Insert the cam lock on panel “B” making

4. Turn the cam lock clockwise. This will lock the

sure it goes aligned to receive the bolt’s head. parts together and will close any gaps.

Alignment: The cross points towards the panel “A” with the bolt.

Panel “B”

P.5

RTA -913D

P.5

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.

Do a quick inventory to make sure the package contains all the parts and hardware listed in the assembly instructions.

To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned correctly.

Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the last pages on this manual.
The replacement parts service is limited to the 48 contiguous United States. If you reside in Alaska, Hawaii, Puerto Rico, U.S. territories or other countries, please contact the supplier from where the unit was purchased.
If during assembly you find an issue or need clarification, please contact our Customer Service for assistance. Please refer to the last pages on this manual.

On each step read the instructions and analyze the illustrations thoroughly before proceeding to do the assembly.

Make sure you

understand

which

hardware will be used on

each step. Using the

wrong size of screw, bolt

or pin might strip the

threads or cause damage

to the part in which it is

being used.

Do not overtighten or force the screws as they might break, strip, damage the threads of the holes or get stuck inside the part.
Sometimes the laminate might cover partially or entirely the hole on a panel. If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole underneath.
# If the hole seems too small for the screw, first make sure you are using the correct size of screw and that it’s been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to reveal the hole’s actual size.

P.6

RTA-913D

P. 6

ASSEMBLY STEPS

STEP 1 Hardware/Tools:

A

10 Dowels Pcs

Place the main panel 1 upside-down over a blanket to protect its finish, and attach the dowels A into the innermost holes, and the bolts B into the outermost holes as shown. Then attach the dowels A into the center hole on the profile of panels 9 and 10.

B

6 Bolts Pcs

1

10

9

(NOT INCLUDED)

10

9

A

B

A

STEP 2 Hardware/Tools:

C

2 Cam locks Pcs

With the help of another person, insert and align the cam locks C into panel 2 and assemble it to the main panel 1 as shown and as explained in page 4. Then cover the cam locks with the stickers I. Finally, assemble the back panel 3 to panel 2 with screws D from the exterior.

D

ST3.5×40 (Flanged)

2 Pcs

Cam lock alignment

I

2 Stickers Pcs

C

I

(NOT INCLUDED)

2

1

3

P.7

RTA-913D

P. 7

STEP 3 Hardware/Tools:

2

1 Sliders Set

Separate all the sliders pieces O according to their shape (no assembly is done here):
-The “Flat” ones will be used in the next step. -The “L” shaped go on the drawer and will be used until step 15.

“FLAT”: Use on step 4 (inside the unit)

“L shaped”: Use until step 15 (on the drawer)

LEFT

LEFT

RIGHT

RIGHT

STEP 4 Hardware/Tools:

H

8 ST3x12 Pcs

O

4 pcs

FLAT

With panels 4 and 6 oriented as shown, attach to them the flat sliders O with screws H. The wheels go towards the front and facing down. For best results, attach at the front of the panels first.

TOP BOTTOM

FRONT

(NOT INCLUDED)

Hole at the back.

(Front)

(Front)

4

6

Hole at the front.
Note: Wheel goes at front and facing down.

P.8

RTA -913D

P.8

STEP 5 Hardware/Tools:

C

2 Cam locks Pcs

D

ST3.5×40 (Flanged)

2 Pcs

Insert and align the cam locks C into panel 4 and assemble it to the main

panel 1 as shown and as explained in page 4. Then cover the cam locks

with the stickers I. Finally, secure the panel 4 to panel 3 with screws D

as shown.

FIRST

Cam lock alignment

I

2 Stickers Pcs

1

C

I

(NOT INCLUDED)
4

THEN

3 4

D

STEP 6

Assemble the lower panel 5 to panel 4 with screws D from the inside.

Hardware/Tools:

D

ST3.5×40 (Flanged)

2 Pcs

(NOT INCLUDED)

4

5

P.9

RTA-913D

P. 9

STEP 7 Hardware/Tools:

C

2 Cam locks Pcs

D

ST3.5×40 (Flanged)

2 Pcs

Insert and align the cam locks C into panel 6 and assemble it to the main

panel 1 as shown and as explained in page 4. Then cover the cam locks

with the stickers I. Finally, secure the panel 6 to panel 5 with screws D

as shown.

Cam lock

FIRST

alignment

I

2 Stickers Pcs

1

C

I

(NOT INCLUDED)

6

THEN

5

6

D

STEP 8

Align the corner of the brackets N along the edge of the top front panel 7

Hardware/Tools: and secure them with screws G as shown.

G

8 ST4x12 Pcs

G

N

4 Angle Pcs

brackets

7

N

(NOT INCLUDED)

P.10

RTA -913D

P.10

STEP 9 Hardware/Tools:

G

8 ST4x12 Pcs

Place panel 7 over the unit making sure it is flushed with the main panel 1 and that it aligns on both ends, and secure it to panel 1 with screws G through the brackets N. Then attach the glide studs K on the bottom of panels 2, 4 and 6 as shown.

K

6 Glide studs Pcs

(NOT INCLUDED)
K

7

2

1

N

4

6

G

STEP 10 Hardware/Tools:

J

22 Nails Pcs

With the help of another person, bring the unit to the upright position,
then assemble the back panel 13 with nails J making sure the panel aligns and fit over all the profiles of panels 1, 4, 5 and 6 as shown.

(NOT INCLUDED)

6 5

1 13
4

STEP 11

For each drawer, assemble panels 9 and 10 to panel 11 with screws E

Hardware/Tools: as shown.

E

ST3.5×40 (Flat)

4 Pcs

(NOT INCLUDED)

11

10

9

P.11

RTA-913D

P.11

STEP 12 Hardware/Tools:

B

8 Bolts Pcs

For each drawer, attach the bolts B to the indicated holes on panel 8. Then insert and align the cam locks C into panels 9 and 10 and assemble them to panel 8 as shown and as explained in page 4. Finally, cover the cam locks with the stickers I.

C

8 Cam locks Pcs

I

8 Stickers Pcs

B

C

I 10

Cam lock alignment

9

(NOT INCLUDED)

8

8

STEP 13 Hardware/Tools:

F

4 ST3.5×25 Pcs

For each drawer, assemble the handle L to the drawer front panel 8 with screws F from inside.
The groove on panel 8 go on the bottom of the drawer.

L

2 Handle Pcs

8

L

(NOT INCLUDED)

The illustration shows the drawer upside-down.

STEP 14

Hardware/Tools:

J

18 Nails Pcs

For each drawer, place the panel 12 on the bottom of the drawer making

sure it enters into the groove of panel 8, then secure panel 12 to panels 9,

10and 11 with nails J as shown.

8

Panel 12 enters into

the groove of panel 8.

(NOT INCLUDED)

12

12 10

11

9

P.12

RTA-913D

P. 12

STEP 15 Hardware/Tools:

H

10 ST3x12 Pcs

For each drawer, assemble the L-Shaped sliders O to the bottom of the drawer with screws H. IMPORTANT: Please pay attention to the orientation of the sliders as
indicated.

O

4 “L” shape Pcs

(NOT INCLUDED)

The wheels go towards the back of the drawer ATTENTION: Incorrect: Will raise 1″ and drawer won’t fit!
Correct:

STEP 16

Insert the drawers into the unit starting with the bottom one. You might need to insert them an angle with the front facing down. If the drawers don’t fit, please review the assembly of the steps 4 and 15.

P.13

RTA -913D

P.13

AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS:

WEIGHT LIMITS

A A = 44 Lbs. (20 Kg) B = 6.60 Lbs. (3 Kg)

B C

C = 15.5 Lbs. (7 Kg)

· Do not exceed the indicated weight limits. · Do not expose the surfaces to direct sunlight or to extreme environmental conditions. · Clean the surfaces preferable with a clean cloth damped in a solution of mild soap and
water, then dry with a clean towel. · Do not use solvents or abrasive materials to clean the unit. · If you decide to use a cleaning agent, test first on an area hidden from view such as
underneath the tabletop. · Do not sit on the unit or lean against it. · Do not allow small children to play under or over the unit. · Do not allow small children to reach inside the drawers without your supervision. · Do not pull, push or drag the unit to move it for more than 1 feet. The unit must be
lifted by at least 2 persons when moving in the same or adjacent rooms. · Before moving the unit, make sure to secure or remove any object that is heavy or
might fall off. · When lifting the unit, use both hands and bend your knees, not your backs. · When transporting the unit to places far away, protect and secure the unit to avoid
damage in transit. · Shall any part of the unit become defective during the warranty period, replacement
parts might be available to you at no charge. Please refer to the last pages on this manual. · The warranty does not extend to regular wear and tear, nor the manufacturer assumes liability for damages or consequences due to accidents, incorrect assembly, negligence, improper use, modifications, or not heeding the above warnings.

P.14

RTA-913D

P.1 4

TECHNI MOBILI DESK WARRANTY

DESKS/LAPTOP CARTS/FILE CABINETS: LIMITED 5-YEAR WARRANTY

RTA Products, LLC warrants to the Original Pu rchaser who acquired a new product from RTA Products or its authorized resellers that this product will be free from defects in its workmanship and materials, under normal use and service conditions, as described herein. “Defects” as used in this warranty, is defined as any imperfections that impair the use of the furniture or product. RTA Products LLC will replace any defective part, at its discretion, and without charge to the original purchaser other than the freight from the end consumer to RTA Products.
Replacement parts can only be supplied if parts are available. Items out of production may be unavailable. This warranty will be effective for the applicable time period beginning the date of purchase on your original sales receipt. RTA product’s obligation under this warranty is limited to repairing or replacing products or parts as provided herein. This product has been designed for and is intended for office and home-office use only. This warranty is Original Purchaser’s sole remedy for product defects, and this warranty does not extend to any product, or damage to any product, caused by or attributed to abuse or misuse, products used for commercial or rental purposes, use modifications of, or attachments to the product, and products or parts not used, maintained, or extended hereunder is in lieu of any and all other warranties, express or implied, including without limitations any implied warranty or merchantability or of fitness for a particular purpose. Please note, all desks made with PVC Laminate surface should not be exposed to direct sunlight, as it may damage the material. Damage of this nature is not covered under this warranty.
RTA Products will not be responsible for indi rect, special, incidental or consequential damages. This warranty is limited to merchandise purchased in the Continental United States, excludes AK, HI and PR. Some States do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights. You may also have other rights that may vary from state to state.
RTA Products will advise you of the procedure to follow in making warranty claims. The following are the procedures for warranty claims:
a. Call us Monday ­ Friday, from 9am-5pm (Eastern Time) at (866) 782-5520 to explain the defect and give your name, address and phone number. Please have ready the model number of our product, date and place of purchase. You can also write to us by e-mail to [email protected] and include the same information.
b. If we determine that replacement will remedtyhe situation, and in order to determine the extent or the cause of the defect, purchaser will need to send the part in question at purchaser’s expense. Once we receive the part, we will examine it and determine whether the claim is valid (or not), and then proceed to send the replacement. We will ship the replacement at our expense.

FOR SEVERAL HELP OPTIONS
INCLUDING REPLACEMENT PARTS ORDERS
_________________________________________________________________
VISIT: WWW.TECHNIMOBILI.COM
CLICK ON SUPPORT TAB
Scan QR Code to order replacement parts OR EMAIL US: [email protected]

References

• Techni Mobili Home and Office Furniture