Joy Pebble Hzb-12-g Portable Automatic Ice Maker Instruction Manual

• The mains lead wires are color-coded for grounding, neutral,
  and live connections.
• Place the appliance on an even or flat surface to ensure
  stability.

• The unit includes an ice scoop, ice full sensor, ice basket,
  top cover with a transparent window, air exhausting system, water
  drain cap, and ice basket handle.
• The maximum water level can be seen by removing the ice
  basket.

• To initiate the self-cleaning program, press and hold the Power
  button for 3 seconds until it starts flashing.
• During cleaning, the indicator will flash in turns.
• After cleaning, drain the water from the inner tank through the
  drainage outlet at the bottom of the machine.

• The control panel allows for easy operation and displays
  functions such as selected ice size, power indicator, ice-full
  indicator, water shortage indicator, and buttons to turn on/off the
  unit and select ice cube size.

• Remove the exterior and interior packaging, and check if the
  ice basket and ice scoop are included. Contact customer service if
  any parts are missing.

PORTABLE AUTOMATIC ICE MAKER
HZB-12/G
Thank you for purchasing this product! If you have any questions about the product, such as missing parts, damaged products, product assembling, or operation, please contact us via Amazon Message or customer service number: 213-4467172 or 661-4358826.

TABLE OF CONTENTS
PREPARING YOUR ICE MAKER FOR USE…………………………….2 IMPORTANT SAFETY TIPS………………………………………………..3 GETTING TO KNOW YOUR UNIT…………………………………………4 Automatic self-cleaning program………………………………………..4 OPERATING PROCEDURES & MAINTENANCE………………………..5 UNPACKING YOUR ICE MAKER…………………………………………..6 CONNECTING YOUR ICE MAKER…………………………………………7 CLEANING AND MAINTAINING YOUR ICE MAKER……………………7 USING YOUR ICE MAKER………………………………………………….8 TROUBLESHOOTING………………………………………………………..8 TECHNICAL PARAMETERS & CIRCUIT DIAGRAM…………………….9 EXPLOSIVE DRAWINGS……………………………………………………10
1

IPMRPEOPRATRAINNGT YSOAUFERTIYCEINMSATKRUERCTFIOORNSUSE
Your safety and the safety of others are very important.
We have provided many important safety messages manual and your appliance. Always read and obey all safety messages. This is the safety alert symbol:
!
All safety messages will follow the safety alert symbol and the word “DANGER” or “WARNING”.
DANGER
WARNING
These words mean: You can be seriously injured if you don’t immediately follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed. When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire, electric shock, and injury to persons or property. Read all instructions before using any appliance. Do not operate thisor any other appliance with a damaged cord.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. This ice-maker must be positioned so that the plug is accessible . Connect to properly polarized outlets only. No other appliance should be plugged into the same outlet. Be sure that the plug is fully inserted into the receptacle. Do not run the power cord over carpeting or other heat insulators. Do not cover the cord. Keep cord away from traffic areas, and do not submerge in water. We do not recommend the use of an extension cord, as it may overheat and become a risk of fire. If you must use an extension cord, use No.14AWG minimum size and rated no less than 1875 watts. Unplug the ice maker before cleaning or making any repairs or servicing. Exercise caution and use reasonable supervision when appliance is used near children. Do not use your ice-maker outdoors. Place the ice-maker away from direct sunlight and make sure that there is at least 4 inches of space between the back of your unit and wall.
2

Keep a minimum distance of 4 inches on each side of your unit free.
Do not use other liquid to make the ice-cube other than water.
Do not clean your ice maker with flammable fluids. The fumes can create a fire hazard or explosion.
Do not tip over.
If the ice maker is brought in from outside in wintertime, give it a few hours to warm up to room temperature before plugging it in.
WARNING: This appliance must be earthed.
DANGER ­ Risk Of Fire or Explosion. Flammable Refrigerant Used. Do Not Use Mechanical Devices To Defrost Ice Maker. Do Not Puncture Refrigerant Tubing.

DANGER ­ Risk Of Fire Or Explosion. Flammable Refrigerant Used. To Be

Repaired Only By Trained Service Personnel. Do Not Puncture Refrigerant Tubing.

CAUTION ­ Risk Of Fire Or Explosion. Flammable Refrigerant Used. Consult Repair Manual/Owner’s Guide Before Attempting To Install or Service This Product. All Safety Precautions Must be Followed.

CAUTION ­ Risk Of Fire Or Explosion. Dispose Of Property In Accordance With Federal Or Local Regulations. Flammable Refrigerant Used .

CAUTION-Risk Of Fire Or Explosion Due To Puncture Of Refrigerant Tubing;Follow Handling Instructions Carefully. Flammable Refrigerant Used.

The ice maker should be installed in accordance with the safety standard for Refrigeration Systems, ASHRAE15. The ice maker shall not be installed in corridors or hallways of public buildings.

If the unit is with problem need to be maintained, that replacing with like components and that servicing shall be done by factory authorized service personnel, so as to minimize the risk of possible ignition due to incorrect parts or improper service.

IMPORTANT:

The wires in this mains lead are colored in accordance with the following code:

Green or Green with a yellow strip :

Grounding

White:

Neutral

Black:

Live

To avoid a hazard due to instability of the appliance, it must be placed at an even or flat

surface.

3

GETTING TO KNOW YOUR UNIT

General instrucion

1. Ice scoop.

2. Ice full sensor

3. Ice basket

4. Top cover with transparent window

5. Air exhausting

6. Water drain cap: at front btm side of the unit.

7 Ice basket handle

8 Ice scoop

9. MAXIMUM WATER LEVEL:

Remove the ice basket, you can see the water level mark.

10. Handle

Automatic self-cleaning program

tPolPuegRntoEenrPtthhAeeRusneIilNtf,-CpGlreeaYsnsOi”ngUOpRNro/OgICrFaFEm”bnMueteAtodKn3oE0nRmcionFnutOtreosRl ,ptahUneeS”lSEfo, rLm” ionrdeicthaatonr

5 seconds, flashes in

turn during cleaning. After cleaning, Drain the water from the inner tank through the

drainage outlet at the bottom of the machine.

4

OPERATING PROCEDURES & MAINTENANCE
Postion of control panel & function
Control Panel: Easy to use, visible functions touch display setting. A. Selected ice size displaying: Small and Large. B. Power indicator C. Ice-Full indicato D .Water shortage indicator E. Button to turn on/off the unit. F. Button to select ice cube size.

D

C

B

A

E

F

5

UNPACKING YOUR ICE MAKER
1. Remove the exterior and interior packaging. Check if ice basket and ice scoop inside. If any parts are missing, please contact our customer service.
2. Remove the tapes for fixing ice shovel, ice basket & ice scoop. Clean the tank & ice basket. 3. Put the ice maker on a level & flat counter top without direct sunlight and other sources of
heat (i.e.: stove, furnace, radiator). Maker sure that there is at least 4 inches gap between the back & LH/RH sides with the wall. 4. Allow one hour for the refrigerant fluid to settle before plugging the ice maker in. 5. The appliance must be positioned so that the plug is accessible.
WARNING: Fill it with potable water only. Only use drinking water. ASSEMBLE HANDLE 1. Rotate the handle to the same angle as the mounting hole on the machin, and put It on the machine.
2. The ice basket handle gets stuck in the ice basket. 3. The ice spoon can be placed on the handle of the ice basket.
6

CONNECTING YOUR ICE MAKER
DANGER
* Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged please call our customer service.
1. This unit should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the possibility of electric shock.
2. Plug your appliance into an exclusive, properly installed, grounded wall outlet. Do not under any circumstances, cut or remove the third (ground) prong from the power cord. Any questions concerning power and/or grounding should be directed toward a certified electrician.
3. This appliance requires a standard 110-120volt, 60Hz electrical outlet with three-prong ground.
CLEANING AND MAINTAINING YOUR ICE MAKER
Before using your ice maker, it is strongly recommended to clean it thoroughly. 1. Take out the ice basket. 2. Clean the interior with diluted detergent, warm water and a soft cloth. 3. Then use the water to rinse the inside parts, and drain out the water by unplugging the
drain cap on front bottom side. 4. The outside of the ice maker should be cleaned regularly with a mild detergent solution and
warm water. 5. Dry the interior and exterior with a clean soft cloth. 6. When the machine is not to be used for a long time, drain water completely & dry the
interior.
7

USING YOUR ICE MAKER

1. Open the cover, remove the ice basket and pour water into the tank. Keep water level below the water level mark.
2. Press “ON/OFF” button on the control panel to begin the ice-making cycle. 3. Select the ice cube size by pressing the “SELECT” button. If the room temperature is lower
than 60, it is recommended to select small ice cube in order to avoid ice sticking together. 4. The ice-making cycle lasts approx. 6 to 13 minutes, depending on the seletion of ice cube
size and the room temperature. The recommended room temperature is 50 to 105 . 5. If water pump can’t inject water, the ice maker will stop automatically, and the “ADD WATER”
indicator will be on. Press “ON/OFF” button, fill water up to the max. water level mark and press “ON/OFF” button again to turn on the unit again. Allow the refrigerant liquid inside the compressor at least 3 minutes to settle before restarting. 6. The ice maker stops when the the ice basket is full and the “ICE FULL” indicator will be on. Warning: Direct sunlight or sunlight reflection may cause infared sensor malfunction. If the unit doesn’t stop even ice cubes obstruct sensor, move the unit to where there’s no sunlight. 7. Change the water in the water reservoir every 24 hours to ensure a reasonable hygiene level. If unit isn’t to be used, drain all the water and dry the tank.
TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

” ADD WATER” indicator is on. “ICE FULL” indicator is on.
Ice cubes stick together.
Ice making cycle is normal but no ice formed.

Lack of Water.
Ice is full in basket.
The ice-making cycle is too long.
Water temperature in the inner tank is too low. Room temperature or water temperature in inner tank is too high. Refrigerant in the cooling system leaks. Pipe in the the cooling system is blocked.

Stop the ice maker, fill water, and press “ON/OFF” button again to restart the unit. Remove the ice from the ice basket. Continuously press “Select” button for 5 seconds, and the unit could make ice for 10 cycles even “Ice” indicator is on. Stop the ice maker, and restart it when the ice blocks melt. Select the small size ice cube selection. Replace the water. The temperature of water is recommended to be at 40 -90. The room temperature should be 50 -105, water temperature should be 40-90.
Verify it by a qualified technician.
Verify it by a qualified technician.

8

TECHNINCAL PARAMETERS & CIRCUIT DIAGRAM

Model Protection Type Power Ice Making Current Ice Harvest Current Refrigerant Design Pressure
High Side Low Side Vesicant Net Weight Dimension ( W * D *H ) Enclosure

HZB-12/G I
115V/60Hz 1.5A 1.8A
R600a 0.74Oz/21g
290Psig 88Psig C5H10 6.3Kg 222x290x294mm Plastic

ELECTRICAL DIAGRAM

WATER LEVEL DETECTING

WATER MCU
T1

MAIN CONTROL PCB

AC-N

+FANMOTOR VALVE AC-L RELAY

+PUMP-

COMP

INFRARED SENSOR DETECTOR
MICRO SWITCH MICRO SWITCH
COND TEMP SENSOR
DC WATER PUMP
DC FAN MOTOR

POWER SUPPLY
N L G

Motor For Ice shovel
SM
Solenoid Valve

COMP

Overload
Protector
C

3S M 2 1 Start Lelay

OPERATION PCB

WATER ICE POWER LED2S LED3L

ON/OFF

SELECT

9

EXPLOSIVE DRAWINGS

S/N Part description

Qty/ Per S/N Part description

Qty

Qty/

/Per S/N Part description

Per

1 Power cord

1 14 Evaporator

1 27 Stainless wire

1

2 plastic clip

1 15 Micro switch

2 28 Water Supply pipe 1

3 Back panel

1

16 Inner tank bracket, LH 1

29 Synchronous motor 1

4 Plate back support 1 17 Back btm panel

1 30 Condenser

1

5 DC water pump

1 18 Back top panel

1 31 DC Fan motor

1

6 Silicon pump sealing 1 19 Displaying PCB

1 32 Nylon plug drain

1

7 Handle

1 20 Touch pad

1

33 Copper tube filter

1

8 Control box cover

1

21 Front top panel

1 34 Rubber foot

3

9 Main PCB

1 22 Water filter

1 35 plastic bottom

1

10 Control box

1 23 Ice scoop

1 36 Compressor

1

11 Ice making box

1 24 Ice basket

1 37 Magnetism valve

1

12 Ice scoop link

2 25 Foaming asm

1 38 Internal Wire

1

13 Ice shovel

1

26 Inner tank bracket, RH 1

10

Thank you for purchasing this product! If you have any questions about the product, such as missing parts, damaged products, product assembling, and operation, please contact us via Amazon Message or customer service number: 213-4467172 or 661-4358826.
IMPORTANT Please call our customer service department for any consulting:
213-4467172 661-4358826 (8:30am – 5:30pm P.S.T.) DATED PROOF OF PURCHASE IS REQUIRED FOR WARRANTY
SERVICE.
AVIS Veuillez appeler le service à la clientèle pour toutes questions au:
213-4467172 661-4358826 (8:30am – 5:30pm P.S.T.) PREUVE D’ACHAT ORIGINALE REQUISE POUR SERVICE DE GARANTIE.
IMPORTANTE Sólo hay que llamar nuestro departamento de servicio
al cliente en caso de tener preguntas o inquietudes: 213-4467172 661-4358826
(8:30am – 5:30pm P.S.T.) SE REQUIERE PRUEBA DE COMPRA CON FECHA PARA
SERVICIO BAJO GARANTÍA.
Address: ROWAN ELECTRIC APPLIANCE LLC 28407 Ascent Way, Santa Clarita, CA 91350 Phone: 213-4467172 or 661-4358826
V1