KD-1400W Sweeper
Product Information: KD-1400W Sweeper
Introduction
The KD-1400W is an electric sweeper used for cleaning
indoor/outdoor floors. It has a dumpster capacity of 1.07 gallons
and a working efficiency of 64585-96878 sqft/h. The sweeper has a
walking motor, rolling brush motor, and brush motor with a
horsepower of 0.13hp, 1.6hp, and 40hp respectively. The product
weighs 1211 LB and has a size of 73*55*55 in.
Operating Instructions
- Turn on the power switch to confirm that the machine power is
normal. The normal voltage is 48 to 54 V, and 48 volts. Do not use
power loss. The battery must be charged as soon as possible. It is
forbidden to store it for a long time without electricity. - Do not use equipment to clean wires or packaging belts,
otherwise ensure that the main brush shaft is cleaned every half a
month. - To achieve the best cleaning effect, please adjust the driving
speed according to the actual situation. When the machine works,
the working speed should be controlled within 5 km/h. Do not pass
through the areas of deep water. - During the operation, it is best to dust the filter at a
specified time interval (25-30 minutes.) The dust time is to clean
the dustbin to achieve the best cleaning effect. - Use the main brush for large area ground cleaning, use the edge
brush only at the edge position. - Do not let the brush rotate when the machine does not move on.
The height of the obstacle should not exceed 50mm. When passing,
the large garbage baffle must be raised slowly and carefully
driving over the obstacle. Fixed obstacle height exceeding 50mm can
only be passed or bypassed using appropriate slopes. - After each use, clean up the bin. It is strictly prohibited to
accumulate to quickly over the bin volume to clean up. - The filter is cleaned once a week, remove the filter and clean
it with an airgun or a brush. The filter is not clean for a long
time, which affects the cleaning effect. - If the sweeper is not used for a long time, please place the
sweeper on a flat ground, and charge the battery about once every
two months. - This machine is an electric product, so it is strictly
forbidden to wash the car body whit water. - Equipment is used to clean the indoor/outdoor floor is not
allowed for modification, do not use the machine as means of
transport. - The machine is limited to personnel trained by the Company, and
all consequences caused by the use shall be borne by other
personnel.
Adjustment of Brush
The main function of the edge brush is to collect the garbage on
both sides to the middle using its own rotation, from the main
brush to the dustbin. The advantage of the edge brush is that it
can sweep out the garbage at corners and dead corners, improving
the cleaning efficiency.
Under normal work conditions, the brush should be slightly bent
from the ground to contact with the ground. If the brush is too low
from the ground, it can cause load heat overload and accelerate the
wear of the bristles. To adjust the side brush height, adjust nut 1
shown in the figure so that the brush slightly contacts the ground
from the ground height.
Operating instruction
KD-1400W
Pay attention to!!!
1this machine is used only as a cleaning tool, and for any other purpose than the instructions stated in this guide, we shall not be liable for any damage resulting therefrom. 2This sweeper can clean the general garbage,should not clean the rope,toxic and harmful, high temperature debris, so as not to wrap, burning the main brush and side brush, so that it can not work normally. 3The machine shall only be used by authorized and trained personnel. 4When the machine stops working, it must be parked on a flat ground. 5Irpersonnel and children should be removed from the scene when the machine is used. 6The power key switch must be closed when opening the hood or machine for maintenance and maintenance.A power cable needs to be removed during mechanical maintenance. 7When transporting the sweeper, confirm that it has been securely tied to the carrier. 8Make sure that the battery is in the ventilated place when charging. IF the sweeper stops working or runs when the underpressure alarm occurs, the battery should be charged in time to extend the battery life. 9When completing the work, unout the key in time to avoid the unrecognized use of the sweeper.
1
Sweeper operation instructions
Turn on the power switch to confirm that the machine power is normal; the normal voltage is 48 to 54 V, and 48 volts. Do not use power loss. The battery must be charged as soon as possible. It is forbidden to store it for a long time without electricity.
Do not use equipment to clean wires or packaging belts, otherwise ensure that the main brush shaft is cleaned every half a month.
To achieve the best cleaning effect, please adjust the driving speed according to the actual situation. When the machine works, the working speed should be controlled within 5 km/h. Do not pass through the areas of deep water.
During the operation, it is best to dust the filter at a specified time interval (25-30 minutes.) The dust time is to clean the dustbin to achieve the best cleaning effect.
Use the main brush for large area ground cleaning, use the edge brush only at the edge position.
Do not let the brush rotate when the machine does not move on. The height of the obstacle should not exceed 50mm. When passing, the large garbage baffle must be raised slowly and carefully driving over the obstacle. Fixed obstacle height exceeding 50mm can only be passed or bypassed using appropriate slopes.
After each use, the requirements to clean up the bin, it is strictly prohibited to accumulate to quickly over the bin volume to clean up.
The filter is cleaned once a week, remove the filter and clean it with an airgun or a brush. The filter is not clean for a long time, which affects the cleaning effect.
If the sweeper is not used for a long time, please place the sweeper on a flat ground, and charge the battery about once every two months.
This machine is an electric product, so it is strictly forbidden to wash the car body whit water.
Equipment is used to clean the indoor/outdoor floor is not allowed for modification,do not use the machine as means of transport.
No cleaning/absorption of items burning or not extinguished. When the user takes the start key form the machine. Do not touch the heating part, such as a running motor, to avoid burns. Only cross slopes below 20%or there is a risk of turning over. When connecting the battery charger to the main circuit,ensure the voltage and frequency. When the key switch is in the on (ON) position, do not connect and remove the battery, do not put tools or similar items on the battery, there is a risk of short circuit or even explosion. Check the tightness of the brake regularly.
The machine is limited to personnel trained by the Company, and all
consequences caused by the use shall be borne by other personnel.
2
Introduction of the sweeper parameters
content voltage Clean the width Main brush width Brush the diameter Working efficiency Working time Dumpster capacity Walking motor Rolling brush motor Brush the motor Speed of travel Battery capacity Water tank capacity Vehicle weight Product size
parameter 48 55 27.5 20
64585-96878 4 40 1.6
1.07 0.13 0-12 150 21 1211 73*55*55
unit V in in in
sqft/h h gal hp hp hp
Km/h ah gal LB in
3
The adjustment of brush
The main function of edge brush is to use its own rotation to collect the garbage on both side to the middle, from the main brush to the dustbin. The advantage of edge brush is that it can sweep out the garbage at the corners and dead corners, and improve the cleaning efficiency.
Under normal work conditions, the brush should be slightly bent from the ground to contact with the ground, the brush is too low from the ground,easy to cause load heat overload, will accelerate the wear of the bristles. Side brush height adjustment method: adjust the nut 1 shown in the figure, so that the brush slightly contacts the ground from the ground height.
The side brush height adjustment as shown in the figure, both sides need to be adjusted, adjust the length of the screw to achieve the height of the main brush from the ground. Normal cleaning side brush contact with the ground 3-5mm, not too close to the ground.
Brush the high and low adjustment
screw on the side
Replacement of brush
Remove Hexagon Screw 1 from motor shaft
Open the sweeper and brush the 4 hands under the screw screws
4
Adjustment of main brush
The width of the main brush touching the ground should be 2-4mm. When the main brush touches the ground too wide, the normal operation of the machine will be affected, and the spare parts are easy to heat up, reducing the service life of the machine.
The main brush height adjustment as shown in the figure, life the shell, adjust the length of the screw out to achieve the height of the main brush off the ground. Normal clean the main brush contact with the ground 3-5mm, not tooclose the ground.
Screw elongation lift main brush
Screw shortening drop main brush
The replacement of the main brush
Unscrew the 3 hand screw screws on the lower guard plate
Unscrew the 4 hand screw nuts on the rocking arm and baffle, and remove the rocking arm and baffle
Take out the main brush. Follow the reverse steps to install the master brush
5
Filter cleaning and replacement
The garbage filter element needs to be checked regularly. When the filter cannot be cleaned or damaged, it needs to be replaced.
As shown in the following figure, clean the filter element steps: 1Unplug the dust motor plug; 2Unscrew the 4 hand screw nuts; 3Unplug the filter element to clean the filter element. Replace the filter element by removing the six inner hexagonal screws in the illustration.
4 Hand screw nuts
Filter element disassembly: Disassemble the six inner hexagonal screws
6
Common fault description
question
The sweeper leaks too large leaves or large particles of garbage
The sweeper left dust or dust on the floor from the
side baffle Cleaning is not thorough, leaving scraps of paper, leaves or other rubbish
The brush wears too fast
Too much noise at work
The brush does not rotate while working
Brush and fan motor are not working
The car cannot move forward and go backward
cause
Work too fast
The brush pressure is too small
The bristles are deformed or wrapped with filaments
The filter is blocked
Fender damage
The front skin lift agency has no work
The brush was pressed too tight
The floor is very rough The bristles are wound
with filaments Bearing bad The brush is over pressed The transmission belt is
damaged
Blown fuse
Damaged pedal governor
Brake pedal position fault
Brake switch fails Controller damage The charger is not
energized
handle Reduce the speed of
working Adjust the pressure of the
brush Remove the winding
material Clean the filter Check the retaining cover and replace it if damaged
Repair the winding material
Reduce brush pressure
Remove the winding material
Replace the bearing Reduce the pressure
Replace the belt
Change the fuse
Replace the governor Check the brake pedal
reset intact Replace the brake switch
Replace the controller Check the charger input
power supply
The battery cannot be charged
The battery discharges too fast
The battery burned
charger Battery terminal is loose Insufficient charging time
Replace the battery
Check the charger for any output
Check and tighten the battery terminals
Increase charging time
7
The electric dust device is not working
The brush can work normally and cannot drive
normally
The battery burned Charger damage Switch bad
The fuse burned The motor load is too large
Motor damage Bearing wear and tear
Problems with controller,fuses,drive motor,governor,brake
switch
Replace the battery Replace the charger Change the switch
Change the fuse Check and reduce the load
Replace the motor Replace the bearing Check the input/output
voltage,indicator lamp,fuse,drive motor,and
connection line
Thank you very much for choosing our product. Before the sweeper is put into use, please read the instructions carefully and strictly follow them to achieve the best cleaning effect and extend the life of the machine. Please contact us for your comments and suggestions. We warmly and quickly serve you.
8
