12201 Leigh Pendant Light Fixture
Product Information: Leigh Pendant Light
The Leigh Pendant Light (SKU 12201) is a stylish and modern
lighting fixture that can be easily assembled. It comes with a
mounting plate, finial nuts, mounting screws, wire nuts, shade set
screws, glass shade, and all the necessary hardware for
installation. The product has been tested to meet specific safety
measures and comes with a free lifetime warranty.
It is important to note that the product should not be modified
in any way and should be used responsibly with safety as the
primary concern. Any modifications may create significant safety
issues, and Nathan James and its parent companies cannot be held
legally responsible for any injuries or death resulting from
improper use of this product.
Product Usage Instructions:
Safety Precautions:
- Inspect the wire insulation for any cuts, abrasions, or exposed
copper that may have occurred during shipping. If there is a defect
in the wire, do not attempt installation. - Before starting the installation, disconnect the power by
turning off the circuit breaker or by removing the appropriate fuse
at the fuse box. Turning the power off at the switch is NOT
SUFFICIENT to prevent electrical shock. - Use hand tools to assemble this product. Do not use power
tools.
Assembly Instructions:
- Separate the Mounting Plate (B) from the ceiling plate and
fixture by removing the Finial Nuts (C). - Install Mounting Bracket to your pre-installed Electrical Box.
Be sure that you are only making the connections to a 120V 60Hz AC
circuit. If you do not have a pre-existing electrical box, we
strongly advise using a certified electrician. - Loosen the set screw on the cord grip on the ceiling plate.
This will allow you to set your desired cord length and pendant
height. Thread excess cord length through the plastic cord stay.
When desire length is achieved, pull to tighten. - When you’ve decided on a length, tighten the set screw on the
cord grip on the ceiling plate. This is to effectively set and hold
the proper cord length to achieve your desired pendant height.
Important Notes:
- Do not tighten bolts/screws completely until all bolts/screws
are lined up and inserted into holes. - Do not over tighten screws and bolts to avoid stripping.
- Do not use the product for commercial purposes, leave spilled
liquid on fixture, use light fixture if damaged, make temporary
repairs, or use outdoors.
If you have any questions or concerns about the product or its
usage, please contact our Customer Happiness team at
[email protected] or call toll-free at 1-866-619-1004.
Let’s build the
Leigh Pendant Light
SKU 12201
5 MINUT
35
SSEMBL
3 Y
E A
Scan me!
Inspiration Digital Instructions Free Lifetime Warranty
22-0826
Ok, let’s get rolling
This should be easy, just follow our instructions and you will be back to Netflix in no time.
Estimated time for assembly
35:00
What you need · Your favorite snack or energy bar
(Save the bubbly for once your fixture is safely installed!) · Use the packaging carton as a working surface to prevent product damage during assembly
Do not use a drill
What’s included
Description
Qty
A Fixture
1
B Mounting Plate
1
C Finial Nuts
2
D M4*25mm Mounting Screws
2
E Wire Nuts
3
F Shade Set Screws
4
G Glass Shade
1
Toll-free at 1-866-619-1004 [email protected] Nathanjames.com/help
Scan me!
Inspiration Digital Instructions Free Lifetime Warranty
2
Safety first, fun later
Safe use of this product starts with you.
Do not modify the structure of this product in any way.
Use this light fixture responsibly with the primary concern for your safety. Follow assembly instructions carefully and inspect product upon receipt and each use.
Nathan James and its parent companies cannot be held legally responsible for any injuries or death resulted from failure to follow instructions or improper use of this product.
Our products have been tested to meet specific safety measures as they were originally intended to be sold. Any modifications will present the risk of creating significant safety issues which Nathan James will not be responsible for.
Proper use
DO NOT DO NOT DO NOT DO NOT DO NOT
use for commercial purposes leave spilled liquid on fixture use light fixture if damaged make temporary repairs use outdoors
WARNING
Inspect the wire insulation for any cuts, abrasions, or exposed copper that may have occurred during shipping. If there is a defect in the wire, do not attempt installation. Please reach out to our Customer Happiness team at [email protected] or 1-866-619-1004
WARNING: RISK OF ELECTRIC SHOCK
Before starting the installation, disconnect the power by turning off the circuit breaker or by removing the appropriate fuse at the fuse box. Turning the power off at the switch is NOT SUFFICIENT to prevent electrical shock. PLEASE CONSULT A QUALIFIED ELECTRICIAN IF YOU HAVE ANY ELECTRICAL QUESTIONS.
3
The goods
A
B
C
D
E
F
G
IMPORTANT 1. Do not tighten bolts / screws completely until all bolts / screws are lined up and inserted into holes. 2. Do not over tighten screws and bolts to avoid stripping. 3. Please use hand tools to assemble this product. Do not use power tools.
4
Pre-Installation
· Read all instructions prior to beginning assembly. · To avoid damaging this product, assemble it on a soft, non-abrasive surface
such as carpet or cardboard. · Keep the receipt and these instructions for proof of purchase. · Use Type G80 Bulbs (not included) · Max. Wattage: 60W · 120V 60Hz AC Only.
Step 1
B
Let’s get this thing fired up! Or should we say, lit!
Separate the Mounting Plate (B) from the ceiling plate and fixture by removing the Finial Nuts (C).
C
C
A
5
Step 2
Install Mounting Bracket to your pre-installed Electrical Box.
Note: Be sure that you are only making the connections to a 120V 60Hz AC circuit. If you do not have a pre-existing electrical box, we strongly advise using a certified electrician.
Electrical Box
B
D
D
6
Step 3
Loosen the set screw on the cord grip on the ceiling plate. This will allow you to set your desired cord length and pendant height.
A
Thread excess cord length through the plastic cord stay.
When desire length is achieved, pull to
tighten.
7
Step 4
When you’ve decided on a length, tighten the set screw on the cord grip on the ceiling plate. This is to effectively set and hold the proper cord length to achieve your desired pendant height.
A
8
Step 5
Use the Wire Nuts (E) to connect the matching colored wires. (White to White, Black to Black & Ground to Ground).
Once complete, tuck the excess wire into the Electrical Box.
Would you believe us if we told you there are only three steps left?
B
Black
E
White
E
Ground Wire (Blue)
E
A
9
Step 6
Secure the ceiling plate and fixture to the Mounting Plate (B) by threading the Finial Nuts (C) into place.
B
To properly fasten the Finial Nuts (C), thread in or out to adjust for proper threading length.
C
C
A
10
Step 7
Remove the Shade Set Screws (F) from the fixture.
A
F
F
11
Step 8
Carefully slide the Glass Shade (G) into the ring of the fixture and then use the Shade Set Screws (F) to hold it in place. Voila! Let there be light!
A
F
F
G We recommend using 1 Type G80 light bulb (not included). Max. Wattage 60W. 120V 60Hz AC only.
Troubleshooting
Problem
Possible Causes
The bulb will not light.
The bulb is burned out.
The power is off.
The fuse blows or circuit breaker blows when the light is turned on.
The circuit breaker is off. There is an exposed wire.
Solutions
Replace the light bulb.
Ensure the power supply is on.
Ensure the circuit breaker is in the ON position. Discontinue use of the light. Contact a qualified electrician or reach out to our Customer Happiness team at [email protected] or 1-866-619-1004.
12
Questions? Don’t worry, we’ve got the answers
What other light bulbs can fit in this light?
The bulb must not be greater than the max wattage for the fixture. It must match the base size, and the diameter of any area of the bulb should be less than diameter of any area of shade, so that it can fit.
Can I use an LED light bulb?
Yes, so long that the base size matches and the diameter of any area of bulb is less than diameter of any area of shade, so that it can fit.
Is this UL/ETL certified?
Yes, all our products are either UL or ETL.
Do I need an electrician to set up the hardwire?
We recommend using a certified electrician for all hardwiring, although all of our fixtures can be set up without an electrician, as long as you are replacing an existing fixture or have an existing junction box ready for a fixture installation. ENSURE POWER IS OFF WHEN INSTALLING. For all new constructions, please use a certified electrician.
Is this light compatible outside North America? Our lighting is only warranted in Canada and the United States.
What do I do if the product is not working? Try a different light bulb and confirm proper installation.
Can these lights work on a dimmer? Dimmability is related to the light bulb and the wall switch, not the light fixture. All our hardwire fixtures are compatible with dimmable light bulbs. We recommend using a dimmer switch, as it extends the life of the bulb and allows for energy saving and great ambiance. If using a LED bulb, please ensure both your LED bulb and dimmer switch are compatible.
Can I use the fixture outdoors? No, this product was designed to be used indoors only in dry locations.
Can I retrofit this hard-wired to a plug-in or vice-versa?
Yes, a plug-in fixture can be turned into a hardwire fixture and a hardwire fixture can become a plug-in fixture. For many products we will provide all the necessary hardware to make these changes, if not, you will need to purchase the necessary hardware.
13
No heartburn, when we handle the return
Give us a call 1-866-619-1004 or shoot us a message at [email protected] we will issue you a free replacement with zero hassle.
Our way
Give us a call Replacement You
Their way
Re-package item Schedule pick up Track package Replacement You
We really don’t want you to go through the hassle of re-packaging your item and sending it back, because let’s be honest…nobody has time for that.
14
We are only in business if you’re happy
For starters, thanks for being you.
Toll-free at 1-866-619-1004 [email protected] NathanJames.com/help
We do our best to ensure your lighting arrives without any problems, but occasionally mistakes happen–as humans we are imperfect beings. In the event that a part is damaged or missing, we will be more than happy to provide you with replacement part(s) for free.
Warranty This product comes with a lifetime warranty from the date of purchase. Please use your phone to scan the QR code to register your product or visit https://goo.gl/i9dk3q
Did we do alright? Please spread the love! If you are happy with your product, tell your friends and family about us or even better leave us a review online. Spreading the word gives us the opportunity to make more people happy and keep our prices low for your next purchase.
Brooklyn Burdon
Founder, Nathan James
15
