PS010VD-3X96-24-W2C 0-10V Power Supply 3 x 96 Watt
Product Information:
Product Name: 0-10V Power Supply 3 x 96
Watt
Model: PS010VD-3X96-24-W2C
Dimensions:
- A. Height: 13.00 inches
- B. Width: 6.60 inches
- C. Depth: 4.20 inches
Maximum Load: 3 x 96 Watts
Product Usage Instructions:
- It is recommended to mount the power supply vertically, at
least 12 inches above the ground level or deck, and 24 inches below
the ceiling. Ensure there is a clearance of 4 inches around the
power supply (excluding the mounting side) to allow for proper air
circulation. Use the provided hardware to mount the power supply to
the wall. - Before installation, check the label on the power supply to
ensure it has the correct input voltage, output voltage, and
wattage for the intended job. Verify that the wire markings match
the wiring diagram provided below. Refer to the table above for the
maximum loads supported by each power supply. - Remove the wiring compartment cover and knockouts on both ends
of the power supply to make the necessary connections. - Connect the white (neutral) and black (hot) power supply wires
to the corresponding white and black power wires (120-277 VAC).
Additionally, connect the ground wires in accordance with local
electrical codes. - Refer to the wiring diagrams on page 2. To insert wires into
the terminal block, use a small flat-head screwdriver to push down
on the terminal block slot, opening the terminal block hole. Insert
the wire lead and release the screwdriver to secure the wire in
place. Ensure the wire size is within the specified range (solid or
stranded: 28-12 AWG) and the strip length is between 0.31 and 0.35
inches. For low-voltage connections, use the Luminii voltage drop
calculator at http://www.luminii.com/voltage-dropcalculator
to calculate the appropriate wire gauge. - Secure the compartment cover back onto the power supply.
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION &
INSTRUCTION WITHOUT NOTICE
0-10V Power Supply 3 x 96 Watt – Installation Instructions
Models PS010VD-3X96-24-W2C
Please read all instructions prior to installation and keep for future reference!
This class 2 power supply is to be installed by a qualified electrician in accordance with the National Electrical Code (NEC) and local building codes. The power supply must be installed in a well ventilated area and free from explosive gases and vapors. Proper operation requires the free flow of air. Power supply is well suited for LED or resistive loads at or below their maximum output rating per circuit. Suitable For Damp Location. WARNING! Risk of Fire or Electric Shock, Do Not Interconnect Output Terminal.
REV0.6 01242023
1 / 2
7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 [email protected] www.luminii.com
Models A. Height B. Width C. Depth MAX Load
PS010VD-3X96-24-W2C 13.00″ 6.60″ 4.20″ 3 x 96 Watts
1
24″ MIN
It is recommended that the power supply be mounted vertically & mount a minimum of 12″ above ground level or deck, 24″ below ceiling, and allow 4″ of clearance around power supply (excluding the mounting side) to provide for proper air circulation. Use the provided hardware to mount properly to wall.
screw & anchor
power supply
12″ MIN
1.1 Before installing, check the label and ensure the power supply has the proper input voltage, output voltage, and wattage for the job. Check the wire markings to ensure they match the wiring diagram below. Refer to table above for the maximum loads supported by each power supply.
2
2.1 Remove the wiring compartment cover and knockouts on both ends of the power supply to connect.
3
120-277VAC wiring compartment
3.1 Connect the white (neutral) and black (hot) power supply wires to the white and black power wires ( 120 – 277 VAC ). Followed by connecting the ground wires in accordance with local electrical codes.
4
4.1 Reference wiring diagrams on page 2. Feed wire into the terminal block hole by intserting a small flat-head screwdriver into the terminal block slot and push down, thus opening the terminal block hole. Then, insert the wire lead and release the screwdriver to secre wire in place.
terminal block
screw driver
screw
terminal block intended wire size solid or stranded : 28 – 12 AWG
strip length : 0.31 – 0.35
use Luminii voltage drop calculator (http://www.luminii.com/voltage-dropcalculator) to calculate wire gage for low-voltage connection
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
0-10V Power Supply 3 x 96 Watt – Installation Instructions
Models PS010VD-3X96-24-W2C
Please read all instructions prior to installation and keep for future reference!
This class 2 power supply is to be installed by a qualified electrician in accordance with the National Electrical Code (NEC) and local building codes. The power supply must be installed in a well ventilated area and free from explosive gases and vapors. Proper operation requires the free flow of air. Power supply is well suited for LED or resistive loads at or below their maximum output rating per circuit. Suitable For Damp Location. WARNING! Risk of Fire or Electric Shock, Do Not Interconnect Output Terminal.
REV0.6 01242023
2 / 2
7777 Merrimac Ave Niles, IL 60714 T 224.333.6033 F 224.757.7557 [email protected] www.luminii.com
5
5.1 Secure compartment cover back onto the power supply.
3 x 96W 0-10V Power Supply
INPUT
0-10 CONTROLLER WIRES
–
-24V
+24V N/A
-24V +24V
N/A N/A N/A
-24V +24V
N/A
Input 120-277V AC
L N GRD
OUTPUT
0-10 CONTROLLER WIRES
–
+
0-10V IN
+
D 1 D2
+
D3 0-10V OUT
+ +
–
–
–
96W MAX PER TERMINAL
LineLED
*LUMINII RESERVES THE RIGHTS TO CHANGE SPECIFICATION & INSTRUCTION WITHOUT NOTICE
Home - Luminii
