Contents hide

2.2 Installation Guide

2.2.1 Documents / Resources

2.2.1.1 References

OMD24SPX1 Microwave Drawer

Product Information: Microwave Drawer

Models: OMD24SPX1 & OMD24SDB1

Installation Guide

IMPORTANT SAFETY AND WARNINGS:

Electric Shock Hazard: Disconnect the
appliance from the mains electricity supply before carrying out any
work or maintenance. Connection to a good earth wiring system is
essential and mandatory. Alterations to the domestic wiring system
must only be made by a qualified electrician.
Cut Hazard: Take care as some edges are
sharp.
Tip Hazard: To reduce the risk of tipping, the
microwave drawer must be secured by a properly installed Anti-Tip
block.

General Use:

Keep this installation guide with your user guide for future
reference.
When using any microwave oven generating heat, there are
certain safety precautions you should follow. These are listed in
the user guide. Read all and follow carefully.
Ensure that your microwave drawer is installed and grounded
properly by a Fisher & Paykel trained and supported service
technician or qualified person.
Do not use an extension cord. If the power supply cord is too
short, have a Fisher & Paykel trained and supported service
technician or qualified person install an outlet near the
appliance.
This appliance must be grounded. In the event of an electrical
short circuit, grounding reduces the risk of electric shock by
providing an escape wire for the electric current. This appliance
is equipped with a cord having a grounding wire with a grounding
plug. The plug must be plugged into an outlet that is properly
installed and grounded.

Prior to Installation:

Ensure that the countertop and oven cavity are square and
level, and are the required dimensions.
Ensure that the installation will comply with all clearance
requirements and applicable standards and regulations.
Ensure that the isolating switch will be easily accessible to
the customer with the oven installed.
Ensure that the electrician provides sufficient free length of
power supply cable to reach from the bottom rear of the cavity to
at least 1.5m in front of the bottom edge of the opening. The cable
may enter the cavity from the side, top or bottom, but top entry
must be at the sealing surface.

Note: The models shown in this installation
guide may not be available in all markets and are subject to change
at any time. For current details about model and specification
availability in your country, please go to our website www.fisherpaykel.com or contact your
local Fisher & Paykel dealer.

View Fullscreen

MICROWAVE DRAWER
OMD24SPX1 & OMD24SDB1 models
INSTALLATION GUIDE US CA

SAFETY AND WARNINGS

WARNING!
Electric Shock Hazard Failure to follow this advice may result in electric shock or death.
z Disconnect the appliance from the mains electricity supply before carrying out any work or maintenance.
z Connection to a good earth wiring system is essential and mandatory.
z Alterations to the domestic wiring system must only be made by a qualified electrician.
WARNING!
Cut Hazard Failure to use caution could result in injury.
z Take care: some edges are sharp.
WARNING!
Tip Hazard Failure to follow this advice may result in damage or personal injury.
z To reduce the risk of tipping, the microwave drawer must be secured by a properly installed Anti-Tip block.

READ AND SAVE THIS GUIDE
General Use
z Keep this installation guide with your user guide for future reference. z When using any microwave oven generating heat, there are certain safety precautions you
should follow. These are listed in the user guide. Read all and follow carefully.
z Ensure that your microwave drawer is installed and grounded properly by a Fisher & Paykel trained and supported service technician or qualified person.
z Do not use an extension cord. If the power supply cord is too short, have a a Fisher & Paykel trained and supported service technician or qualified person install an outlet near the appliance.
z This appliance must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.
z WARNING Improper use of the grounding can result in a risk of electric shock. z Consult a qualified electrician or serviceman if the grounding instructions are not
completely understood, or if doubt exists as to whether the appliance is properly grounded. z Do not install drawer in any combustible cabinetry, which is not in accord with the stated clearances and dimensions on pages 6-8. z Ensure that the wall coverings and the cabinets around the microwave drawer can withstand the heat generated. z Never leave children alone or unattended in the area where a microwave drawer is in use. Never leave the drawer open when the microwave is unattended. z Stepping, leaning or sitting on the drawer may result in serious injuries and can also cause damage to the microwave drawer. z Do not use the microwave drawer as a storage space. This creates a potentially hazardous situation. z Check that the time of day is in the display. If not, touch STOP / CLEAR to prevent unintended use. z Refer to the user guide for cleaning instructions. z Contact surface must be solid and level. The floor of the opening should be constructed of plywood strong enough to support the weight of the oven 100lbs (45kg). z Check location where the microwave drawer will be installed for proper electrical supply. z Oversized foods or oversized metal utensils should not be inserted in a microwave oven as they may create a fire or risk of electric shock. z Do not clean with metal scouring pads. Pieces can burn off the pad and touch electrical parts involving a risk of electric shock. z Do not use paper products when appliance is operated in the grill mode. z Do not store any materials, other than manufacturer’s recommended accessories, in this oven when not in use. z Do not cover racks or any other part of the oven with metal foil. This will cause overheating of the oven.

SAVE THESE INSTRUCTIONS
The models shown in this installation guide may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please go to our website www.fisherpaykel.com or contact your local Fisher & Paykel dealer.
3

SAFETY AND WARNINGS
z Remove all packing materials from inside the microwave drawer. Do not remove the waveguide cover, which is located on the top of the microwave drawer (see illustration on below for waveguide cover location).
z Remove the feature sticker, if one is present. Check the drawer for any damage, as a misaligned or bent drawer, damaged drawer seals and sealing surfaces, broken or loose microwave drawer guides and dents inside the cavity or on the front side of the drawer, If there is any damage, do not operate the microwave drawer and contact your dealer or visit www.fisherpaykel.com.

Sealing surface Waveguide cover

Sealing surface Oven cavity

PRIOR TO INSTALLATION
Ensure that:
The countertop and oven cavity are square and level, and are the required dimensions. The installation will comply with all clearance requirements and applicable standards and
regulations. The isolating switch will be easily accessible to the customer with the oven installed. The electrician provides sufficient free length of power supply cable to reach from the
bottom rear of the cavity to at least 1.5m in front of the bottom edge of the opening. The cable may enter the cavity from the side, top or bottom, but top entry must be at the
rear of the cavity. The oven connection socket (if fitted) is outside the cavity if the oven is flush to the rear
wall. The oven will rest on a surface that can support its weight. The height from the floor suits the customer. You consult local building authorities and by-laws if in doubt regarding installation.
Some environmental factors and cooking habits can cause condensation in and around the oven during use. To protect surrounding cabinetry from possible damage caused by frequent or excessive condensation, we recommend moisture-proofing the oven cabinetry.

COMPONENTS REQUIRED
PARTS
z Keep all packaging materials until the unit has been inspected. z Inspect the product to ensure there is no shipping damage. If any damage is
detected contact the dealer or retailer you bought the product from to report the damage. z Fisher & Paykel is not responsible for shipping damage.

Supplied

Not supplied

Phillips Screw 7/8″ (22mm) (4)

Anti-tip block (1)

AFTER INSTALLATION
The manufacturer does not accept any responsibility for damage resulting from incorrect installation. Ensure that: The oven door(s) can open fully without obstruction. The power supply cable does not touch any hot metal parts. The isolating switch is easily accessible to the customer with the oven installed. You complete the `Final checklist’ at the end of the installation. If, after following the instructions given, correct performance cannot be achieved, please contact your nearest Fisher & Paykel Authorised Service Center, Customer Care, or contact us through our local website listed at the end of this document.

TOOLS
Not supplied

Powered driver

Cross-head screwdriver

PRODUCT DIMENSIONS

e m
l

DATUM FRONT OF CHASSIS

PLAN VIEW

k
DATUM BOTTOM OF PRODUCT

B 606mm

g
i A

j
FRONT VIEW

Milimeters
6

n f

ANTI TIP BLOCK

Model no: OMD24SDB1
Product Dimensions a Overall height B Overall width c Overall depth d Height of chassis e Width of chassis f Depth of chassis g Height of control panel h Drawer opening distance i Gap between door and control panel j Height from bottom datum to bottom of door k Height of door l Depth of electrical inlet m Width of electrical inlet n Control panel depth o Height to bottom of anti tip block
*Anti tip block is not supplied with product. Include in cabinetry design

mm 405 606 592 374 557 552
78 330
5 6 316 102 122 40 377

inch 15 15/16″
23 7/8″ 23 5/16″
14 3/4″ 21 15/16″
21 3/4″ 3 1/16″
13″ 3/16″
1/4″ 12 7/16″
4″ 4 13/16″
1 9/16″ 14 13/16″

Dimension Clearances Minimum inside height of cavity Minimum inside width of cavity Minimum inside depth of cavity

inch

393

15 1/12″

562

22 1/8″

557

21 15/16″

INDICATES CABINETRY / PRODUCT DATUM ————————INDICATES CABINETRY CLEARANCES ——————————-IMPORTANT NOTE: Throughout this guide, dimensions may vary by ±2mm (1/16”). Please read the installation manual for detailed information on installing the product. For full installation instructions & specifications visit fisherpaykel.com

PROFILE VIEW

DATUM FRONT OF CHASSIS

PRODUCT DIMENSIONS

e m
l

DATUM FRONT OF CHASSIS

PLAN VIEW

k
DATUM BOTTOM OF PRODUCT

B 606mm

g
i A

j
FRONT VIEW

Milimeters

n f

ANTI TIP BLOCK

Model no: OMD24SPX1
Product Dimensions a Overall height B Overall width c Overall depth D Height of chassis e Width of chassis f Depth of chassis g Height of control panel h Drawer opening distance i Gap between door and control panel j Height from bottom datum to bottom of door k Height of door l Depth of electrical inlet m Width of electrical inlet n Control panel depth o Height to bottom of anti tip block
*Anti tip block is not supplied with product. Include in cabinetry design

mm 405 606 592 374 557 552
75 330
6 6 319 102 122 40 377

inch 15 15/16″
23 7/8″ 23 5/16″
14 3/4″ 21 15/16″
21 3/4″ 2 15/16″
13″ 1/4″ 1/4″ 12 9/16″
4″ 4 13/16″
1 9/16″ 14 13/16″

Dimension Clearances Minimum inside height of cavity Minimum inside width of cavity Minimum inside depth of cavity

393

15 1/12″

562

22 1/8″

557

21 15/16″

PROFILE VIEW

DATUM FRONT OF CHASSIS

g i

CABINETRY DIMENSIONS
c f
h

PROFILE

PLAN

CABINETRY DIMENSIONS A Minimum inside height of cavity flush B Minimum inside height of cavity proud C Overall width of cabinetry D Overall height of cabinetry flush E Overall height of cabinetry proud F Minimum inside width of cavity G Minimum inside depth of cavity H Anti-tip block width I Anti-tip block depth J Height from bottom of cabinetry to bottom of Anti-tip block

INCHES 16 1/16 15 9/16 24 17 9/16 17 1/16 22 1/8
21 15/16 6
3 1/2 14 13/16

MM 408 395 610 446 433 562 557 150
90 377

If installing a cooktop above the oven, ensure adequate clearance is provided as per the cooktop manufacturer’s instructions. 8

PROUD INSTALL 3/4″(19mm)
1 9/16″ (40mm)
FLUSH INSTALL 5/8-13/16″ (16- 20mm)
1/16″ (2mm)

PLUMBING & ELECTRICAL CONSIDERATIONS
z This oven must be connected to the mains power supply only by a suitably qualified person.
z This oven must be earthed.

Before connecting the oven to the mains power supply, check that: the domestic wiring system is suitable for the power drawn by the oven (as specified on the rating plate) the voltage corresponds to the value given on the rating plate.

MODEL CODE

OMD24SPX1, OMD24SDB 60 Hz

VOLTAGE (V) 120 V

AMPS (A) 15

Model and serial number location
z Open the microwave drawer fully. The label is beyond the back wall of the microwave cavity facing up from the flat surface.

ANTI-TIP BLOCK INSTALLATION

To reduce the risk of tipping of the drawer, the anti-tip block must be correctly installed, located 14 13/16″ (377mm) above the cabinetry floor on which the microwave drawer will sit.

· The 6″ (152mm) anti-tip block must be provided by the installer.

· The anti-tip block prevents serious injury that might result from spilled hot liquids.

Prepare install location.

Install the anti-tip block into the

cabinetry 14 13/16″ (377mm) above cabinetry floor level. Ensure the screws

are fitted into wood or metal for stability.

Take care to avoid electrical wiring and plumbing when securing.

If the microwave drawer is to be moved, the anti-tip block must also be moved and reinstalled.

DRAWER INSTALLATION

Place the drawer adjacent to the wall or

cabinet opening. Plug the power supply

cord into the electrical outlet.

Secure the drawer using the 4 x 7/8″ (22mm) screws supplied.

Carefully guide the drawer into the

cavity. Avoid pinching the cord between the

oven and the wall.

Push the drawer in until the mounting

flange is flush with the face of the

cabinet.

Open the drawer. Using the four holes on

the drawer as a template, pre-drill the

cabinet using a 1/16″ (1.6mm) drill bit.

INSTALLER CHECKLIST
Read all installation guidance in this document to see if the unit has been correctly installed. Ensure that installation has been completed correctly before use. TO BE COMPLETED BY THE INSTALLER

Installation
Ensure the microwave drawer is level and securely fitted to the cabinetry.
Open the microwave drawer slowly until it is fully open and check there is adequate
clearance between the bottom of the door and the lower trim. This is to ensure correct air circulation. Should the lower trim become damaged, straighten the trim and ensure the microwave drawer door opens fully without obstruction.
Ensure any cable ties and internal packaging have been removed from the microwave
drawer cavity.
Ensure all microwave drawer vents and openings are clear and free of any obstruction or
damage.
Ensure cavity ventilation has been set up correctly.
Failure to make sure all microwave drawer vents are clear may result in poor product performance.
Ensure the isolating switch is accessible by the customer.

Electrical
Ensure all electrical tests have been conducted in accordance with local regulations. Check electrical outlet is accessible in the adjacent cabinetry.

Complete and keep for safe reference:
Model Serial No. Purchase Date Purchaser Dealer Address Installer’s Name Installer’s Signature Installation Company Installation Date 12

FISHERPAYKEL.COM
© Fisher & Paykel Appliances 2023. All rights reserved. The models shown in this guide may not be available in all markets
and are subject to change at any time. The product specifications in this guide apply to the specific products and models described at the date of issue. Under our policy of continuous product
improvement, these specifications may change at any time. For current details about model and specification availability in your country,
please go to our website or contact your local Fisher & Paykel dealer.
431251A 05.23