TXFBB12 12 Inch Swing Gate Mounted Subwoofer Enclosure for Ford Bronco
Product Information
The Powerey TXFBB12 is a 12″ swing gate mounted subwoofer
enclosure designed specifically for the Ford Bronco. It is a
high-quality product that requires technical skill, experience, and
specialized tools for installation. The recommended amplifier
rating for this subwoofer enclosure is 400-800 watts at 2 ohms. It
is important to read the installation guide thoroughly before
disassembling or modifying the vehicle. If unsure, it is
recommended to have the product professionally installed by an
authorized Stinger or AudioControl Dealer. The product comes with a
limited warranty.
Product Usage Instructions
- Remove the four Philips screws from the speaker and set them
aside. - Remove the contents from inside the enclosure.
- Open the hardware pack and check the quantities and tools
required using the guide provided. - Recommended tools for installation include a #2 Philips
screwdriver, 9mm drill bit, scissors, 5mm Allen wrench, drill,
rivet nut setter (optional), 14mm wrench, center punch, 10mm
socket, hammer, ratchet, tape, socket extension, and wire
strippers. - Refer to the hardware guide to identify the different types of
bolts, washers, brackets, and other hardware included in the
pack. - Follow the steps below for installation:
- Using scissors or a straight edge and utility knife, cut out
the template provided along the dashed lines. - Position the template on the inside of the swing gate using the
plastic trim panel as a guide. Align the left and right cross-hairs
on the template to the register marks on the trim panel and ensure
the template is straight. - Securely tape the template to the swing gate.
- Using a center punch, mark the four mounting locations on the
template. - Remove the template and drill pilot holes at the marked
locations. - Drill 9mm holes at the four marked locations.
- Remove the swing gate trim panel by releasing the retaining
clips along the bottom and swinging it up to release the locking
tabs along the top. - If a rivet nut setter is not available, follow the provided
directions for each of the four holes.
- Using scissors or a straight edge and utility knife, cut out
Note: It is recommended to watch the video installation guide
available at https://stingerelectronics.com/products/txfbb12
for visual instructions and further assistance.
®
Powere y
TXFBB12
12″ SWING GATE MOUNTED SUBWOOFER ENCLOSURE
FOR FORD BRONCO
INSTALLATION GUIDE
NOTE! Read this installation guide thoroughly before disassembling or modifying the vehicle. Installation of this product requires technical skill, experience and
specialized tools. If in doubt, it’s recommended to have it professionally installed by an authorized Stinger or AudioControl Dealer.
A video installation guide is available at: https://stingerelectronics.com/products/txfbb12
Limited Warranty
Stinger warrants this product to be free of defects in materials and workmanship for a period of one (1) years from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Stinger dealer in the United States of America only. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Stinger will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty. INTERNATIONAL WARRANTIES: Products purchased outside the United States of America are covered only by that country’s Authorized Stinger reseller and not by Stinger. Consumers needing service or warranty information for these products must contact that country’s reseller for information.
2
INSTALLATION NOTES
For models equipped with a factory subwoofer, unplugging the factory subwoofer is recommended. Some installation steps are more easily completed with a second person. Speaker wire is required before the enclosure is mounted. Recommended amplifier rating: 400-800 watts @ 2ohms. Do not power up until inside contents are removed.
GETTING STARTED
Remove the four Philips screws from the speaker and remove the speaker. Set speaker and screws in a safe place.
Remove contents from inside the enclosure.
Open the hardware pack and confirm hardware quantities and tools required using the guide on the following pages.
RECOMMENDED TOOLS
#2 Philips Screwdriver
9mm Drill Bit (Included)
Scissors
5mm Allen Wrench
Drill
Rivet Nut Setter (Optional)
14mm Wrench
Center Punch
10mm Socket
Hammer
Ratchet
Tape
Socket Extension
Wire Strippers
3
HARDWARE
B1
B2
W1
W2
M6 FLANGED HEX HEAD BOLT (2) M6 ALLEN HEAD BOLT (4)
40mm / 1.57in Length
20mm / .78in Length
W3
L1
M6 SPLIT LOCK WASHER (2) 11mm / .43in Diameter
L2
M6 METAL WASHER (3) 18mm / .71in Diameter
T1
M6 RUBBER WASHER (2) 18mm / .71in Length
B3
BOTTOM L BRACKET (2)
N1
FOAM BRACKET PAD (2)
W4
MOUNTING TEMPLATE (1)
R1
M6 HEX HEAD BOLT (2) 40mm / 1.57in Length
P1
M8 HEX NUT SPACER (2)
P1
M6 TOOTH LOCK WASHER (2)
M6 RIVET NUT INSERT (5)
M5 PHILIPS HEAD SCREW (4) 30mm /. 78in Length
(Removed from speaker)
M5 PHILIPS HEAD SCREW (6) 30mm / .78in Length
(Included in hardware)
POLY-FILL (1)
NOTE: Hardware images not to scale. There will be hardware left over depending on the installation
4
INSTALLATION
1
Using scissors or a straight edge and utility knife, cut out the template along the dashed lines.
2
Position the template on the on the inside of the swing gate using the plastic trim panel as a guide as shown.
Align the left and right cross-hairs on the template to the register marks on the trim panel (1). Verify the template is straight by confirming the horizontal line on the template (2) follows the horizontal groove on the plastic trim panel.
Once aligned, securley tape the template to the swing gate.
ACCESSORY READY
2
2
ACCESSORY READY
1
1
5
INSTALLATION
3
Using a center punch, mark the four mounting locations on the template.
Remove the template and drill pilot holes at the four locations.
CAUTION: To prevent the drill bit from hitting the outer side of the swing gate, wrap a significant amount of tape around the drill bit leaving only ½” of the bit exposed.
Drill 9mm holes at the four marked locations.
ACCESSORY READY
2
4x
9
mm
4
Remove the swing gate trim panel using a nylon panel tool or similar to release the retaining clips (1) along the bottom, then swing up (2) to release the locking tabs along the top.
2
1
1
2
1
1
6
INSTALLATION
5
If a rivet nut setter is not available, follow the directions below for each of the four holes:
A. Insert a R1 rivet nut into the hole.
B. Slide an W2 metal washer, a N1 spacer nut and a W4 tooth lock washer onto one of the B3 bolts.
C. Hand thread the bolt into the rivet nut until it is hand tight.
D. Using a 14mm wrench to hold the spacer nut, start tightening the bolt with a 10mm socket. Ensure the the rivet nut remains fully inserted and flat against the panel surface while tightening. The wrench and spacer nut should be held in place; do not rotate. The rivet nut takes approximately 12-13 quarter turns to propery seat. The bolt will get harder to turn when the rivet nut is seated.
E. Once installed, loosen and remove the 10mm bolt while continuing to hold the spacer nut in place with the wrench.
NOTE: After installing the first rivet nut, ensure the side of the spacer nut that was positioned against the tooth lock washer is the same for the remaining installations.
There are two bolts, spacer nuts and washers provided in the event they are needed.
TIP: Having a second person hold the wrench in place and using two hands to tighten with the ratchet will allow you to apply more forward pressure while tightening, keeping the insert flush against the panel.
W2 N1 W4 R1 B3
7
INSTALLATION
6
In the two lower threaded inserts, install L1 brackets using B2 allen bolts.
Apply the L2 Foam Bracket Pads to the brackets.
L1 B2
L2
L1 B2
L2
7
Run a suitable length of speaker wire into the swing gate following the factory wire harness. Connect the speaker wire to the terminals. Positve (+) is Red and Negative (-) is Black. Route the speaker wire in the channel.
8
INSTALLATION
8
Align the speaker enclosure on the L Brackets. Loosley install the indicated hardware into the upper mounting holes from inside the enclosure.
Install the two B2 Allen Head Bolts through the L Brackets and into the bottom of the enclosure.
Once all the bolts are threaded, tighten all hardware.
W3 W2 W1
B1
2x
B2
9
A. Place the sheet of poly-fill inside the enclosure along the back and side areas.
B. Connect the speaker leads inside the enclosure to either of the speaker terminals on the speaker. Positve (+) is Red and Negative (-) is Black.
NOTE: Ensure the pre-installed speaker terminal jumper wires stay connected when connecting the wires to the speaker terminal.
C. Align the speaker and install eight P1 screws securing the speaker.
P1
C
8x
B
A
9
SPECIFICATIONS
Model Number Speaker Model Subwoofer Size Voice Coil DC Resistance (Re) Sensitivity 1W/M (SPL) Frequency Response RMS Power Speaker Displacement Speaker Weight
Enclosure Specifications Internal Volume Enclosure Weight Height Width Depth Depth (with Speaker & Grill)
TXFBB12 SPC-12S2 12″ Single 2 ohm 2 ohm 87 dB 20Hz – 250Hz 400 watts 0.06 cu ft / 1.82 Ltr 12.5 lbs
0.706 cu ft. / 19.99 Ltr 16.25 lbs 17in / 43.2cm 27.5in / 69.9cm 4.6in / 11.7cm 5.8in / 14.7cm
Height 17in / 43.2cm
W
Width
H
27.5in / 69.9cm
Depth 4.6in / 11.7cm
D
10
11
Stinger is a Power Brand of AAMP Global 15500 Lightwave, Clearwater, Florida 33760
Phone: 888-228-5560
Technical Support
Phone: 727-592-5991 Email: [email protected] Chat: stingerelectronics.com
Stinger and the Stinger logo are trademarks or registered trademarks of AAMP Global in the United States and other countries.
© 2021-2023 AAMP Global. All rights reserved. | IG-TXFBB12 REV 011923
Stinger Electronics
