Hearth Home Technologies Dm6036 Bi-fold Glass Doors Instruction Manual

DM6036 Bi-Fold Glass Doors

Product Information

Product Models: DM6036, DM6036-S, DM8042, DM8042-S Glass
Doors

Installation Instructions:

• CAUTION! Risk of Cuts/Abrasions. Wear protective gloves and
  safety glasses during installation. Sheet metal edges are
  sharp.
• WARNING: HOT SURFACES! Screen/mesh, glass doors, and other
  surfaces are hot during operation AND cool down. Hot screen/mesh
  and glass doors will cause burns. Keep flammable materials
  away.

Product Usage Instructions

1. Install the Door Track:
   1. Place the top door track behind the front face and secure it
      with a screw. See Figure 1.
   2. Attach the spring clips to the top door track for adjustment.
      See Figure 2.
   3. Pull down on the spring clips to adjust the position of the
      door track. Tighten the screws to secure the adjustment. See Figure
      3.
2. Slide the Side Filler In:
   1. Push the screens to the center of the fireplace opening.
   2. Slide the side filler in front of the side refractory with the
      notch at the bottom and the tabs to the front. See Figure 4.
   3. Fasten the side filler to the corresponding holes in the column
      using the screws provided in the 2nd fastener pack.
   4. If there are no holes in the side column, use the side filler
      as a template and drill holes in the column. Fasten filler to
      column.
3. Attach the Bottom Pin to the Door Track:
   1. Insert the bottom pin into the hole in the bottom door track.
      See Figure 6.
4. Adjust and Secure the Sliding Doors:
   1. Attach the pivot pins to the top door track. See Figure 7.
   2. Place the sliding doors onto the pivot pins.
   3. Adjust the position of the doors using the top spring
      clip.
   4. Slide the doors in or out as needed.
   5. Tighten the screws on the top spring clip to secure the doors
      in place.

tm
Models: DM6036, DM6036-S DM8042, DM8042-S Glass Doors

Installation Instructions

These bi-fold glass doors have been tested for use with specific Hearth & Home Technologies products. Check with your local building code agency before you begin installation to ensure compliance with local codes, including the need for permits and follow-up inspections. If you encounter any problems regarding code approvals, or if you need clarification of any of the instructions contained here, contact your Hearth & Home Technologies dealer. For the dealer nearest you, please visit www.hearthnhome.com.
Note: An arrow () found in the text signifies change in content.
CAUTION! Risk of Cuts/Abrasions. Wear protective gloves and safety glasses during installation. Sheet metal edges are sharp.

WARNING
HOT SURFACES!
Screen/mesh, glass doors and other surfaces are hot during operation AND cool down.

Hot screen/mesh and glass doors will cause burns.
· Do not touch screen/mesh or glass doors until cooled · NEVER allow children to touch screen/mesh or glass
doors
· Keep children away · CAREFULLY SUPERVISE children in same room as
fireplace. · Alert children and adults to hazards of high
temperatures.
High temperatures may ignite clothing or other flammable materials. · Keep clothing, furniture, draperies and other flammable
materials away.

Figure 1 – Install the Door Track

· Starting with the left side going in first, slip the bottom door track along the front edge of the hearth refractory and line it up end to end. See Figures 1-2.
· Install the top door track behind the front face. Secure the track in place with one screw from fastener pack, in the center.
· On each end of the top door track, add a spring clip to each end and secure with 2 screws each (they are also adjustment screws), also from fastener pack See Figure 3. If door pin doesn’t reach, it may be necesaary to adjust angle on spring clip by pulling down on clip after install.

Figure 2 – Installed Door Track

Hearth & Home Technologies · DM6036/DM8042 Glass Doors · 33797 Rev I · 03/23

1

TOP DOOR TRACK
(FRONT FACE) SPRING CLIPS
1 Screw

TOP DOOR TRACK PLACED
BEHIND THE FRONT FACE

ADJUSTMENT

PULL DOWN TO ADJUST

SCREWS

Figure 3 – Spring Clip Placement

· Install the Side Fillers
a. Push the screens to the center of the fireplace opening.
b. Slip the side filler in front of the side refractory with the notch to the bottom and the tabs to the front. See Figure 4.

Figure 5 – Fastening the Side Filler
d. Repeat for the other side. · Fold up one door (handles at the bottom) and set the
bottom pin into the hole in the bottom door track. See Figure 6.

Notch

Figure 6 – Bottom Pin/Door Track
· Slide the top pins on the door into the top door track. Slide the door over until the pivot pin snaps into the spring clip. See Figure 7.

Figure 4 – Slide the Side Filler In

c. Fasten the side filler to the corresponding holes in the column with the screws provided in 2nd fastener pack.

Note: If there are no holes in the side column, use the side filler as a template and drill holes in the column. Fasten filler to column.

Figure 7 – Pivot Pins/Top Door Track
· Repeat Steps 6-7 for the other side. · To adjust the door alignment, loosen the screws at the
top spring clip, sliding doors in or out, then tightening the screws.

2

Hearth & Home Technologies · DM6036/DM8042 Glass Doors · 33797 Rev I · 03/23

References

• hearthnhome.com