GY21088-1 Wooden FM Radio Music Player DIY Kit
Product Information:
- Product Name: Wooden FM Radio Music Player DIY Kit
- Work Voltage: DC 3V
- Speaker: 3W 4ohm
- Channel: Single-Channel Mono
- Audio source: FM
- Receiver Frequency: 88.0MHz~108.0MHz
- Control Type: On Board Button
- Output type: Speaker
- Power Type: AA*2 Battery
- Work Temperature: -20~85
- Work Humidity: 5%~85%RH
- Size (Installed): 117*73*40mm
Product Usage Instructions:
- Step 1: Remove all available boards from the 4 wooden boards.
Be careful not to damage the wooden board. - Step 2: Fix 1pcs 3W 4ohm Speaker on Wooden Board by 4pcs M2*4mm
Screw. - Step 3: Paste double-sided adhesive on the back of the FM Radio
Receiver Module. - Step 4: Paste and fix FM Radio Receiver Module on another
Wooden Board by 4pcs M2*7mm Screw. Note: Loosen the screws slightly
and do not tighten them too tightly. - Step 5: Fix 1pcs AA*2 Battery Box on another Wooden Board by
2pcs M2*4mm Screw. - Step 6: Splicing wooden boards from battery box and FM
receiver. Connect the battery socket while placing the wires in the
wiring slot. - Step 7: Fix FM Antenna gasket by 2pcs M2*6mm Screw.
- Step 8: Fix FM Antenna and gasket from FM Radio Receiver Module
by 1pcs M2*7mm Screw. - Step 9: Insert fixed small bracket.
- Step 10: Connect the 3W 4ohm Speaker to FM Radio Receiver
Module. - Step 11: Splicing wooden boards from FM receiver and
speaker. - Step 12: Fix TOP wooden board by 2pcs M2*7mm Screw. Note: Align
each installation hole. - Step 13: Slowly bend the wooden board to avoid breaking and
then fix by 2pcs M2*10mm Screw. - Step 14: Fix Bottom wooden board by 2pcs M2*7mm Screw.
- Step 15: Slowly bend the wooden board to avoid breaking and
then fix by 1pcs M2*10mm Screw. - Step 16: Install 2pcs AA Battery.
- Step 17: Fix the last wooden board by 1pcs M2*7mm Screw.
- Step 18: Slowly bend the wooden board to avoid breaking and
then fix by 1pcs M2*7mm Screw. - Step 19: Install 4pcs Black Sponge Base on Bottom wooden
board.
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
1.Introduction: It is a FM Radio Amplifier Mono FM Music Player Handmade Wooden Assembly
Experimental Equipment. It uses a wooden casing to create a very primitive FM radio. It can play music from FM radio with the 3W 4ohm speaker produce clear and loud sound.The use of screws for fixation makes installation very convenient and simple.
2.Feature: 1>.Pure wooden shell board 2>.FM Audio Player with built-in power amplifier 3>.Adjustable Radio Station and Volume 4>.Single Channel Mono Speaker
3.Parameter: 1>.Product Name:Wooden FM Radio Music Player DIY Kit 2>.Work Voltage: DC 3V 3>.Speaker: 3W 4ohm 4>.Channel: Single-Channel Mono 5>.Audio source:FM 6>.Receiver Frequency:88.0MHz~108.0MHz 7>.Control Type:On Board Button 8>.Output type: Speaker 9>.Power Type: AA*2 Battery 10>.Work Temperature:-20~85 11>.Work Humidity:5%~85%RH 12>.Size(Installed):117*73*40mm
4.Package: FM Radio Receiver Module x1 Wooden Boards x4 3W 4ohm Speaker x1
1
Wooden FM Radio Music Player DIY Kit
AA*2 Battery Box x1 FM Antenna x1 Black Sponge Base x4 Double-Sided Tape x1 M2*10mm Screw x3 M2*7mm Screw x11 M2*6mm Screw x2 M2*4mm Screw x6 Screwdriver x1 Transparent Plastic Box x1
https://www.icstation.com/ Email: [email protected]
5.Installation Steps(Please be patient): 1>.Step 1: Remove all available boards from the 4 wooden boards. Be careful not to
damage the wooden board. 2>.Step 2: Fix 1pcs 3W 4ohm Speaker on Wooden Board by 4pcs M2*4mm Screw. 3>.Step 3: Paste double-sided adhesive on the back of the FM Radio Receiver Module. 4>.Step 4: Paste and fix FM Radio Receiver Module on another Wooden Board by 4pcs
M2*7mm Screw. Note:Loosen the screws slightly and do not tighten them too tightly. 5>.Step 5: Fix 1pcs AA*2 Battery Box on another Wooden Board by 2pcs M2*4mm
Screw. 6>.Step 6: Splicing wooden boards from battery box and FM receiver. Connect the
battery socket while placing the wires in the wiring slot. 7>.Step 7: Fix FM Antenna gasket by by 2pcs M2*6mm Screw. 8>.Step 8: Fix FM Antenna and gasket from FM Radio Receiver Module by 1pcs
M2*7mm Screw. 9>.Step 9: Insert fixed small bracket. 10>.Step 10: Connect the 3W 4ohm Speaker to FM Radio Receiver Module. 11>.Step 11: Splicing wooden boards from FM receiver and speaker. 12>.Step 12: Fix TOP wooden board by 2pcs M2*7mm Screw. Note: Align each
installation hole. 13>.Step 13: Slowly bend the wooden board to avoid breaking and then fix by 2pcs
M2*10mm Screw. 14>.Step 14: Fix Bottom wooden board by 2pcs M2*7mm Screw. 15>.Step 15: Slowly bend the wooden board to avoid breaking and then fix by 1pcs
M2*10mm Screw. 16>.Step 16: Install 2pcs AA Battery. 17>.Step 17: Fix the last wooden board by 1pcs M2*7mm Screw. 18>.Step 18: Slowly bend the wooden board to avoid breaking and then fix by 1pcs
M2*7mm Screw. 19>.Step 19: Install 4pcs Black Sponge Base on Bottom wooden board.
6.Install shown steps:
2
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
3
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
4
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
5
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
6
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
7
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
8
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
9
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
10
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
11
Wooden FM Radio Music Player DIY Kit
https://www.icstation.com/ Email: [email protected]
12
ICStation Developing and Providing Worldwide With IC Accessories, Raspberry Pi, Robots, Arduino compatible Dev. Board and Modules
