ALLISON 10L1000 4WD Stage 1 Transmission
Product Information:
The 10L1000 is a transmission assembly designed for vehicles. It
features solenoids that require unique performance characteristic
data to function efficiently. This data is programmed and stored in
the vehicle’s transmission control module (TCM). The solenoid
characterization reprogramming process ensures that the solenoids,
valve body, and transmission are properly matched.
Product Usage Instructions:
- Perform the solenoid valve characterization reprogramming using
the TIS2Web Service Programming System (SPS). - Document the new Transmission Unique Number (TUN) after a
transmission component replacement. - Log into TIS2Web/SPS and enter the vehicle identification
number (VIN). - Perform the SPS Transmission Control Module programming
event. - Select the applicable service procedure from the MCVM
(Mechanical Characterization and Virtual Matching) Operation
Selection screen. Provide the necessary Transmission Unique Number
(TUN) when replacing a transmission part. - Perform the service fast learn procedure.
- Road test the vehicle for 200-300 miles at no more than 30%
throttle. - Recheck for leaks and ensure proper ATF levels.
For further assistance or inquiries, contact Revmax Converters
at 1-877-780-4334 or visit their website at www.revmaxconverters.com.
10L1000 INSTALL
INSTALLATION INSTRUCTIONS
www.revmaxconverters.com
1
10L1000 Install
INSTALLATION INSTRUCTIONS
First steps of install:
· Install transmission to engine block. · Install the torque converter bolts · Install the starter motor. · Install the transmission support crossmember. · Install the transfer case. · Install the transmission range selector lever cable to the transmission. · Lower the vehicle. · Connect the negative battery cable. · Fill the transmission to the proper level.
Dexron® ULV – 19352619
Step 2:
Perform the solenoid valve characterization reprogramming. Solenoid Valve Characterization Reprogramming
The solenoids in this transmission require unique performance characteristic data in order to function at maximum efficiency. This data is programmed and stored in the vehicle’s transmission control module (TCM). When a transmission assembly, TCM, or solenoids are replaced during service, the performance characteristic data for the solenoids must be retrieved from a web server “cloud” repository and reprogrammed into the TCM.
Reprogramming also ensures that the characteristic data relationship is properly matched between the solenoids, valve body, and transmission.
Solenoid characterization reprogramming is performed using the TIS2Web Service Programming System (SPS).
NOTE: ****The TUN and PUN was sent with the transmission****
www.revmaxconverters.com
2
10L1000 Install
INSTALLATION INSTRUCTIONS
Solenoid Reprogramming Procedure
To perform solenoid characterization after a transmission component replacement: 1. Document the new Transmission Unique Number (TUN). 2. Log into TIS2Web/SPS. 3. Type the vehicle identification number (VIN). 4. Perform the SPS Transmission Control Module programming event.
· Select “Transmission Control Module – Programming” to update TCM calibrations and Solenoid Characterization data.
OR · Select “Transmission Control Module – MCVM Operations” to update Solenoid
Characterization data only. 5. From the “MCVM (Mechanical Characterization and Virtual Matching) Operation Selection” screen, select the applicable service procedure to be performed. You will be prompted to provide the necessary Transmission Unique Number (TUN) when replacing a transmission part.
At this point, the system will read the VIN from the engine control module (ECM) using the multiple diagnostic interface (MDI) and then retrieve the applicable genealogy data tree from the cloud. This data tree accesses the original characterization data so that it may be updated with the new component information. The system acquires characterization data for the given TUN/PUN via the cloud and updates the genealogy tree. The TCM is updated with the correct solenoid characterization data, and the cloud is updated with the new genealogy relationship.
Perform the service fast learn procedure.
www.revmaxconverters.com
3
10L1000 Install
INSTALLATION INSTRUCTIONS
Conditions for Running the Procedure
Transmission Fluid Temperature = 75 to 85°C (167 to 185°F)
Reference Information
With Scan Tool OEM Version
1. Engine » Idling — At normal operating temperature 2. Select: Module Diagnostics 3. Select: Transmission 4. Select: Configuration/Reset Functions 5. Select: Learn Functions 6. Select: Transmission Service Fast Learn 7. Follow the instructions on the scan tool. Verify the scan tool procedure was successful.
· If the procedure was not successful Refer to: Step 1
8. If the procedure was successful 9. All OK. 10. Road test for 200-300 miles at no more than 30% throttle 11. Recheck for leaks and proper ATF levels.
www.revmaxconverters.com
1-877-780-4334 4520 Westinghouse Blvd | Suite B
Charlotte, NC 28273
www.revmaxconverters.com
4
Shop Transmissions, Torque Converters - RevMax Converters
