99352 Catalina Nailhead Headboard
Product Information: Nailhead Headboard
The Nailhead Headboard is a furniture product that can be
assembled to the wall or attached to a bed frame. It comes with a
set of assembly hardware and a hex screwdriver. The product is
designed to be used in a bedroom setting as a decorative and
functional addition to a bed. It is recommended to read the entire
instruction booklet before starting the assembly process.
Product Usage Instructions:
- Precautions: Keep unassembled parts away from
children under 3 years of age and animals. Parental supervision is
required during assembly. Children should not climb or pull on the
headboard to avoid damage to the unit. - Assembly at a Glance: Take a moment to read
through the whole instruction booklet before assembly to
familiarize yourself with this product. Once ready, follow the
instructions step by step. - Component Parts: Check that you have all the
parts listed, including assembly hardware. - Assembly Instructions:
- Remove #2 Legs (x2) bolted to the back of 1.
- Attach #2 Leg (x2) to #1 with A bolt (x4).
- If attaching to a bed frame, insert A bolt into #2 leg and
attach it to your bedframe mount on your bedrails (not included)
with B washer and C Nut. - If mounting the headboard to the wall, use the paper wall mount
template (included in the back of instructions) to mark your holes
and ensure your mounts are even and level. Drill small pilot holes
and install Dx4 into the pilot holes with a hammer. Insert E (x2)
into each hole of 3 and tighten with a screwdriver into D wall
anchors. Repeat for other E. - Congratulations, your Nailhead Headboard is complete!
- Wall Mount Instructions: Make sure your
template is level before marking your holes. Use masking tape to
temporarily secure the template on the wall when ensuring paper is
completely flat and even. Use a level to adjust position. Then
press a pencil through the center of marked holes on the template
to mark pilot hole target behind paper. Remove paper template when
satisfied with placement and proceed to Wall Mount Instruction step
1.
Nailhead Headboard
Assembly Instructions Product Dimensions: 62″W×3″D×48″H
Please take a moment to read through the entire instruction booklet before assembly to familiarize yourself with this product. Once you feel ready to start, follow the instructions
step by step and this should make this process as easy as we could make it for you.
.
Page 1 of 9
WARNING ! CAUTION
ADULT ASSEMBLY REQUIRED CHOKING HAZARD · This product includes small parts, sharp points and sharp edges in its unassembled state.
Keep unassembled parts away from children under 3 years of age, and animals.
SAFETY WARNINGS · Follow the information on the warnings appearing on headboard and on the
carton. Do not remove warning label from headboard. · Do not allow children under 3 years of age to use the headboard . · Do not use substitute parts. Contact the manufacturer or dealer for replacement parts.
FURNITURE TIP-OVER HAZARD Children have died from furniture tip-over To reduce the risk of furniture tip-over: · ALWAYS install tip-over restraint especially if used by a wall or in the open. · NEVER allow children to stand, climb or hang on headboard. · ALWAYS anchor headboard to wall or bedframe.
PARENTAL SUPERVISION IS REQUIRED
· Parents or Guardians should supervise use under the intended age specifically regarding children that may have access to it and climb on the unit.
· Do not allow horseplay on, under, or behind the unit and prohibit jumping on the unit. · If used improperly, your unit may be pulled over or fall, creating risk of injury or
damage. Children should not be permitted to climb or pull on the headboard.
USE, MAINTENANCE & ASSEMBLY · Periodically check and ensure that the components are in their proper position, free from · damage, and that all connectors are tight. · Use on level surfaces only. Assemble on a soft level surface to avoid damage to unit or floor. · Do not use this item if any components are missing or damaged. · Do not use substitute parts. Contact the manufacturer or dealer for replacement parts. · Only clean using damp cloth and mild detergent, do not use bleach or abrasive cleaners. · Check you have all components and tools listed on page 4 · Do not stand or put weight on this product during assembly, this could cause damage. · Remove all hardware from the plastic bags and separate them into groups. · Assemble the item as close to its final position (in the same room) as possible. · Certain assembly steps may be easier with 2 people. · Dispose of all packaging carefully and responsibly. · We do not recommend power screwdrivers. Only use hand screwdrivers to prevent
damage to unit.
Keep these instructions for future reference.
Enfants morts suite au basculement d’un meuble. Han muerto ninos por el vuelco de meubles.
Afin de limiter le risque de basculement de meuble:
Para limitar el riesgo de vuelco de los meubles:
· TOUJOURS utiliser les fixations anti-basculement.
· Utilisar SIEMPRE las fijaciones antivuelco que suministran.
· NE JAMAIS installer de TV sur ce produit.
· NUNCA instalar un TV sobre este producto.
· NE JAMAIS laisser d’enfants se tenir debout sur les tiroirs,
· NUNCA permitar que los ninos se pongan de pie, trepen o
portes ou etageres, y grimper ou s’y suspendre.
se cuelguen de los cajones, puertas o baldas.
· NE JAMAIS ouvrir plus d’un tiroir a la fois.
· NUNCA abrir mas de un cajon a la vez.
· TOUJOURS placer les choses les plus lourdes dans les tiroirs du bas. ·Colocar los objetos mas pesados en los cajones inferiores.
Page 2 of 9
ASSEMBLY AT A GLANCE
Please take a moment to read through the whole instruction booklet before assembly to familiarize yourself with this product. Once you feel ready to start, follow the instructions step by step and this should make this process as easy as we could make it for you.
3 3
1
2
2
This drawing is to give you an overall idea only of how this assembly will go together and does not replace the assembly instructions.
Page 3 of 9
COMPONENT PARTS
Please check that you have all the parts listed below
1. Headboard ×1
3
2. Leg ×2
3. Mounting Brackets ×2
3
1
2
2
A
M8 ×4
ASSEMBLY HARDWARE
B
Washer ×4
E
Screw ×4
C
Nut ×4
D
Wall Anchors ×4
F Hex Screwdriver (included)
Page 4 of 9
ASSEMBLY INSTRUCTIONS
1
Remove #2 Legs (x2) bolted to back of 1
1
1
2 2
2
Attach #2 Leg (x2) to #1 with A bolt (x4).
1
A A
2
Page 5 of 9
A A
2
A A
ASSEMBLY INSTRUCTIONS
3
(SKIP THIS STEP IF MOUNTING HEADBOARD TO WALL) If attaching to bedframe, Insert A bolt into #2 leg and attach to your bedframe mount on your bedrails (not included) with B washer and C Nut.
1 2
2
A B C
2
Page 6 of 9
ASSEMBLY INSTRUCTIONS
1
Measure using paper wall
mount template (included in
D
the back of instructions) to D
mark your holes and ensure
your mounts are even and
level. Drill (tool required –
not included) small pilot
holes and install Dx4 into
the pilot holes with hammer
(tool required – not includ-
ed). Insert E (x2) into each
hole of 3 and tighten with
screwdriver into D wall
anchors. Repeat for other E. .
D D
D D
3
E
E
2
Hang 1×1 on the wall.
1
1
1
Steps 1
Steps 2
Page 7 of 9
ASSEMBLY INSTRUCTIONS
CONGRATULATIONS, YOUR NAILHEADHEADBOARD IS COMPLETE!
Page 8 of 9
ASSEMBLY INSTRUCTIONS
Back of Assembly Instructions
400mm
Folded Paper Template
400mm
400mm
400mm
Make sure your template is level before marking your holes. Use masking tape to temporarily secure template on wall when ensuring paper is completely flat and even. Use a level to adjust position. Then press pencil through center of marked holes on template to mark pilot hole target behind paper. Remove paper template when satisfied with placementand proceed to Wall Mount Instruction step 1.
400mm
400mm
Page 9 of 9
