Bestway 58761e Aquadrift Automatic Pool Cleaner Owner's Manual

1. Clean the debris compartment by rinsing it with water to remove
   debris.
2. Clean the pressure relief valve filter by rinsing it with water
   to remove debris.
3. Clean the pool suction fitting by rinsing it with water to
   remove debris.
4. For filter pump, stop the pump, block the connector A and B to
   avoid water flowing out from the pool, and clean the filter
   cartridge or replace if necessary.
5. For sand filter pump, disconnect the cleaner from the pool,
   perform backwash and rinse to clean the sand.
6. If there are wrinkles at the bottom of the pool, level the pool
   to reduce them.
7. Check and clean the debris screen inside the head.
8. Check and clean the filter cartridge or backwash the filter
   sand if dirty.
9. Check and remove debris from the wheel.
10. Open the water valve if it did not open.

©2022 Bestway Inflatables & Material Corp. All rights reserved Trademarks used in some countries under license from Bestway Inflatables & Material Corp., Shanghai, China Exported by Bestway (Hong Kong) International Ltd./Bestway Enterprise Company Limited Suite 713, 7/Floor, East Wing, Tsim Sha Tsui Centre, 66 Mody Road, Kowloon, Hong Kong Distributed in North America by Bestway (USA) Inc., 3435 S. McQueen Road, Chandler, AZ 85286, United States of America Tel: +86 21 69135588
www.bestwayusa.com

OWNER’S MANUAL
58761E AquaDriftTM Automatic Pool Cleaner

OPERATING WARNING
IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS. WARNING: To reduce the risk of injury, do not permit children to use this product. WARNING: Assembly and disassembly of this product should only be performed by adult. WARNING: Do not remove or obstruct the float opening while the filter pump/sand filter is operating. WARNING: Keep hands and hair away from the Pool Vacuum while the filter pump/sand filter is operating. WARNING: Do not use the filter pump/sand filter while the pool is occupied. WARNING: Ensure the filter pump/sand filter is unplugged before any maintenance begins or severe risk of injury or death exists. NOTE: Remove the product from the pool before placing a cover over the pool. NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.

PART LIST

ITEM 1

NAME Flap

QTY

1

1

2

Main Body

1

3

Debris Compartment

1

4

Bottom Cover

1

2

5

Hose

1

6

Pressure Relief Valve

1

7

Pressure Relief Valve Filter

1

8

Seal

1

9

Brush

10

Float

1

3

2

11

Hose Adapter

1

12

Hose Clamp

1
4

6 7 8 9 10

11

5

12

Applicable Pump: 1,500-3,200 gal./h Filter Pump or Sand Filter Applicable Pool: 22 ft. (6.7 m) and below Above Ground Pool
INSTALLATION

1

2

3

3m4m

0.5m1m

4.1

5.1

6.1

7.1

A

A

A

A

2

4.2

5.2

6.2

7.2

8

A

B

B A

A A

HOW TO USE THE PRODUCT
If the following situations occur during operation, please operate as shown to keep the robot in the best working condition. 1. During operation, if the hose sinks below the water surface, please adjust the position of the float. 2. When adapting to a high-flow pump, if the following situations occur, please refer to the operation diagram, and adjust the pressure relief valve knob to appropriately
reduce the running speed of the cleaner: 2.1. After the hoses are straightened out, serious hose entanglement occurred in continuous long-term operation; 2.2. The robot runs too fast, the wheels tip over or the wheels do not move along the bottom of the pool. 3. When the robot runs for a long time, if the running track does not cover most of the pool area, or the running track is repeated. Please adjust the wheel angle knob appropriately. 4. When adapting to 1500 gal. filter pump, please remove the brush. NOTE: It is normal for the robot to leak water at the water pipe joints during the water supply process.
1

2

3

4
3

HOW TO CLEAN THE PRODUCT

1

2

3

4

5

6

7

8

TROUBLESHOOTING

Problem
Robot does not capture the debris, moves slowly or does not move at all.
The hoses are entangled The driving path of the robot cannot cover the entire pool

Possible Cause Debris compartment is full Pressure relief valve filter is clogged Pool suction fitting is clogged
The filter cartridge or sand is too dirty
Air inside the pump
The robot is stuck on wrinkles
Wheel is jammed The water valve did not open Damaged debris compartment or pressure relief valve filter
Hose not straightened out
The hose sinks into the water The robot running speed is too fast The wheels are not in the correct position

Solution Clean the debris compartment. Rinse with water to remove debris. Clean the pressure relief valve filter. Rinse with water to remove debris. Clean the pool suction fitting. Rinse with water to remove debris. Filter pump – Stop the pump, block the connector A and B to avoid water flowing out from the pool,
and clean the filter cartridge or replace if necessary. Sand filter pump – Disconnect the cleaner from the pool, perform backwash and rinse to clean the sand.
Stop the filter pump or sand filter, purge the air and start again. Check the bottom of the pool. If there are wrinkles, level the pool to reduce them. Check to see if the debris screen inside of the head is dirty. Clean the debris screen. Check to see if the filter cartridge or filter sand is dirty. Clean the filter cartridge or back wash the filter sand. Check and remove debris from the wheel. Open the water valve
Return to the shop to get assistance
Turn off the pump, reconnect the product at the diagonal position of the pool, the water hose should be in a C shape, the product should be placed into the water in the direction of the water hose. Adjust the position of the float to make the hose float on the water. Regulating pressure relief valve
Adjust the wheel driving angle

4 303021300607

References

• Home Page