Contents hide

2 Product Information: Scene Controller ZEN32 800LR

ZEN32 800LR Scene Controller

Product Information: Scene Controller ZEN32 800LR

The Scene Controller ZEN32 800LR is a Z-Wave switch that offers
on/off control, trigger scenes, and control other devices in your
Z-Wave network. It has a 15 A relay and a NEW 800 series Z-Wave
chip for better range and faster control. It works with regular
on/off switches in a 3-way and has Z-Wave Long Range for ultra
reliable no-mesh communication. Additionally, it has Smart bulb
mode, adjustable LED indicator in 4 colors and 3 brightness levels,
S2 Security, and SmartStart for easier inclusion.

Specifications:

Model Number: ZEN32 800LR
Z-Wave Signal Frequency: 908.40 MHz, 908.42MHz, 916.00MHz,
912.00MHz, 920MHz
Power: 120 VAC, 60 Hz
Maximum Load: 150W LED, 960W Incandescent, Resistive, 3A motor
(DON’T use with receptacles), 1800W (15A)
Range: Up to 500 feet line of sight
Installation and Use: Indoor only

Caution:

Before installing the Scene Controller ZEN32 800LR, it is
recommended that a licensed electrician perform the installation in
accordance with the National Electric Code and local regulations.
This product should be installed indoors upon completion of any
building renovations. Prior to installation, the device should be
stored in a dry, dust-and-mold-proof place. Do not install the
switch in a place with direct sun exposure, high temperature, or
humidity. Keep away from chemicals, water, and dust. Ensure the
device is never close to any heat source or open flame to prevent
fire. Ensure the device is connected to an electric power source
that does not exceed the maximum load power. No part of the device
may be replaced or repaired by the user.

Product Usage Instructions:

Unscrew: Carefully turn the screw counter clockwise to make
space for the wire. Do not unscrew completely.
Press Down: Once it’s loose, press the screw down with your
finger so it catches the thread.
Insert Wire: Make sure the wire is perfectly straight, then
insert it into the terminal while holding the screw down. Do not
wrap wires around the terminal screws!
Tighten: Turn the screw clockwise to tighten the wire. Do not
overtighten!
Complete Installation: Secure your Z-Wave switch in the box
with mounting screws, handling the wires with care. Install the
wall plate and restore power to the circuit.
Test the Switch: The LED indicator should light up as soon as
you turn the power back on if the switch (light) is OFF. Tap the
switch button for ON and tap it again for OFF. If the test fails,
please check that:
- Power is fully restored to the circuit
- Wiring matches the instructions exactly
- The load isn’t too large and overheating the switch causing it
  to shut off
Z-Wave Control:
1. Add Device to Your Hub: Initiate inclusion (pairing) in the app
  (or web interface).
2. Finalize Inclusion at the Switch: Tap the switch button 3 times
  quickly.

View Fullscreen

USER MANUAL

HOW TO INSTALL THE WIRES

PROGRAMMING

SCENE CONTROLLER ZEN32 800LR

www.getzooz.com [email protected]

Scan to register your product for extended warranty and direct access to firmware files.

1. UNSCREW: carefully turn the screw counter clockwise to make space for the wire. DO NOT

unscrew completely.

2. PRESS DOWN: once it’s loose, press the screw down with your finger so it catches the thread.

3. INSERT WIRE: make sure the wire is perfectly

straight, then insert it into the terminal while

STRIP WIRE AT 1/2-5/8″ holding the screw down. DO NOT wrap wires

around the terminal screws!

4. TIGHTEN: turn the screw clockwise to tighten

the wire. DO NOT OVERTIGHTEN!

FIRMWARE VERSION 2.10
FEATURES
Y Switch button: 15 A relay for Z-Wave on/off control Y 4 remote control buttons: trigger scenes and control other
devices in your Z-Wave network from this switch Y NEW 800 series Z-Wave chip for better range and faster control Y Direct 3-Way: works with regular on/off switches in a 3-way Y Z-Wave Long Range for ultra reliable no-mesh communication Y Smart bulb mode: disable relay and control the light via Z-Wave Y Adjustable LED indicator in 4 colors and 3 brightness levels Y S2 Security and SmartStart for easier inclusion

SPECIFICATIONS

Y Model Number: ZEN32 800LR

Y Z-Wave Signal Frequency: 908.40 MHz,908.42MHz,916.00MHz,

912.00MHz,920MHz

Y Power: 120 VAC, 60 Hz

Maximum Load: 150W LED, 960W Incandescent, Resistive, 3A motor (DON’T use with receptacles)

1800W

(15A)

Y Range: Up to 500 feet line of sight

Y Operating Temperature: 32-104° F (0-40° C)

Y Installation and Use: Indoor only

CAUTION

This is an electrical device – please use caution when installing and operating the scene control switch. Remote control of appliances may result in unintentional or automated activation of power. Do not use this Z-Wave device to control electric heaters or other appliances which produce the risk of fire, burns, or electrical shock when unattended. To reduce risk of overheating and possible damage to other equipment, do not install this unit to control a receptacle; a motor-operated appliance; a fluorescent lighting fixture; or a transformer-supplied fixture.

BEFORE YOU INSTALL
This switch is intended for installation in accordance with the National Electric Code and local regulations. It is recommended that a licensed electrician perform this installation.

COMPLETE INSTALLATION Secure your Z-Wave switch in the box with mounting screws, handling the wires with care. Install the wall plate and restore power to the circuit.
TEST THE SWITCH The LED indicator should light up as soon as you turn the power back on if the switch (light) is OFF. Tap the switch button for ON and tap it again for OFF. If the test fails, please check that: Y power is fully restored to the circuit Y wiring matches the instructions exactly Y the load isn’t too large and overheating the switch causing it to
shut off
WARNING
Y This product should be installed indoors upon completion of any building renovations. Y Prior to installation, the device should be stored in a dry, dust-and-mold-proof place. Y Do not install the switch in a place with direct sun exposure, high temperature, or humidity. Y Keep away from chemicals, water, and dust. Y Ensure the device is never close to any heat source or open flame to prevent fire. Y Ensure the device is connected to an electric power source that does not exceed the
maximum load power. Y No part of the device may be replaced or repaired by the user.
Z-WAVE CONTROL
1. ADD DEVICE to your hub
Initiate inclusion (pairing) in the app (or web interface). Not sure how? Scan one of the QR codes below for step-by-step instructions or get in touch: www.support.getzooz.com
2. Finalize inclusion at the switch. TAP THE SWITCH BUTTON 3 TIMES QUICKLY
if using traditional Z-Wave inclusion.
SCAN THE QR CODE / ENTER THE 5-DIGIT DSK if using the new SmartStart method.
The LED indicator will blink blue to signal communication and turn green for 3 seconds if inclusion is successful or turn red for 3 seconds if the pairing attempt fails.
NEED SOME HELP? [email protected]

WIRING: READ IT!

Choose your hub and scan the QR code with your phone’s

1. CHECK THE LOAD: lights only (150W for LED’s, 600W for incandescent), DON’T CONNECT THIS SWITCH TO OUTLETS

camera. Then click on the link to access the step-by-step pairing instructions.

OR TUBE LIGHTS.

2. POWER OFF: turn the circuit power off in the breaker panel

before you start. If installing in a multi-switch box with

multiple circuits, turn power off at all of the circuits.

3. CHECK THE WIRES: mark load (most o en black), line

SmartThings

Hubitat

Home Assistant

(most o en black), neutral (most o en white), and ground

Get more tutorials and helpful tips at ww.support.getzooz.com

(most o en bare). 14 AWG wires only! Don’t rely exclusively

TROUBLESHOOTING

µon your multimeter to identify the wires!

The switch won’t add to your system? Try this:

NOT SURE WHAT YOU’RE SEEING? WE’LL HELP! SUPPORT.GETZOOZ.COM SEND US PICTURES OF YOUR SET-UP, BEFORE YOU DISCONNECT WIRES.
4. REMOVE THE OLD SWITCH: disconnect the wires and label them with the included label stickers. 5. CONNECT THE Z-WAVE SWITCH: follow all installation steps carefully. Wire the switch EXACTLY like in the diagram.

1. Initiate EXCLUSION and tap the switch button 3 times quickly.
2. Tap the switch button 4-5 times quickly when adding it. 3. Bring the gateway controller (hub) closer to the switch, it
may be out of range.
4. Get troubleshooting tips for your hub at

ZEN32 WIRING DIAGRAM FOR SINGLE POLE INSTALLATION
1 Insert the ground (bare) wire into the Ground terminal (not shown in the diagram)

www.support.getzooz.com The switch won’t control the lights manually anymore? Try this: 1. Turn the power off at the breaker and check if a wire

2 Insert the power source wire to Line terminal and load wire to Load terminal. Load and line CAN’T be swapped so make sure you identified them correctly!

didn’t get loose. 2. Exclude the switch from the hub or reset it in case
manual control was accidentally disabled.
3. The load may be incompatible so try it with a single

incandescent bulb.

There are 2 ways you can use the buttons on the Scene Controller to control other Z-Wave devices in your network:
1. Scene Control: Y Great to trigger preset scenes with multiple devices Y Perfect for smart bulb control and non Z-Wave devices Y Supports 1-tap, 2-tap, 3-tap, 4-tap, 5-tap, button held, and
button released for each button
2. Direct Association Y Great to control other Z-Wave devices directly Y Perfect for Z-Wave smart bulb control or as a virtual add-on for
existing Z-Wave switches and dimmers Y Use only for Z-Wave devices included with the same security
level as your Scene Controller Y Supports 1-tap for on/off control (Group 2) and button
held/released for dimming (Group 3), working in a sequence: press once to change state or hold to dim / increase brightness
Programming your Scene Controller using either of the above methods will depend on the capabilities and interface layout of your Z-Wave system. Scan one of the below QR codes to get step-by-step instructions for your hub and if it’s not listed, get in touch: [email protected]
Choose your hub and scan the QR code with your phone’s camera. Then click on the link to access the instructions.

Z-Box Hub

SmartThings

Hubitat

Home Assistant

Get more tutorials and helpful tips at www.support.getzooz.com

HOW IT WORKS?
SWITCH BUTTON: reports association Group 1 lifeline to the hub, Group 2 basic set, Group 3 multilevel; reports Scene 5 with 7 attributes (actions) BUTTON 1: Group 4 basic set, Group 5 multilevel; Scene 1 (7 actions) BUTTON 2: Group 6 basic set, Group 7 multilevel; Scene 2 (7 actions) BUTTON 3: Group 8 basic set, Group 9 multilevel; Scene 3 (7 actions) BUTTON 4: Group 10 basic set, Group 11 multilevel; Scene 4 (7 actions)

TAP x 1 for on/off of the connected load; Scene 5, pressed (or basic set for association Group 2) TAP x 2, 3, 4, or 5 for Scene 5 multi-tap HOLD for Scene 5 held (or start level change); multilevel to Group 3 RELEASE for Scene 5, released (or multilevel stop level change)
S2

SWITCH BUTTON

TAP x 1 Scene 1-4 pressed (or basic set for
Group 4, 6, 8, and 10) TAP x 2, 3, 4, or 5 for Scene 1-4 multi-tap HOLD for Scene 1-4 held (or start level change);
multilevel to Group 5, 7,
9, and 11 RELEASE for Scene 1-4 released (or multilevel
stop level change)

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from other manufacturers and/or other applications. All non-battery operated nodes within the network will act as repeaters regardless of vendor to increase reliability of the network. This product features the latest Security 2 (S2) framework to remove smart home network hacking risks. This device is equipped with a unique authentication code for trusted wireless communication. This is an ETL certified device. ETL, just like UL, is a Nationally Recognized Testing Laboratory. The ETL mark is proof of product compliance with North American safety standards.
WARRANTY
This product is covered under a 1-year limited warranty with extended 5-year warranty once it’s registered. To read the full warranty policy, register your product, or file a warranty claim, please go to www.getzooz.com/warranty

SEE BACK PAGE FOR 3-WAY & 4-WAY DIAGRAMS AND INSTRUCTIONS
3 Run the white jumper (included in the box) from the bundle of white wires to the Neutral terminal
DON’T FORCE THE SCREWS. Look up to see how to install the wires correctly.
PAGE 1

EXCLUSION (REMOVING / UNPAIRING DEVICE)
1. Bring your Z-Wave gateway (hub) close to the switch if possible
2. Put the Z-Wave hub into exclusion mode (not sure how to do that? [email protected])
3. Tap the switch button 3 times quickly (the LED indicator will start blinking blue)
4. Your hub will confirm exclusion, the LED indicator on the switch will turn green for 3 seconds, and the device will disappear from your controller’s device list
FACTORY RESET
If your primary controller is missing or inoperable, you may need to reset the device to factory settings. To reset the switch, press and hold the switch button for 20 seconds until the LED indicator starts flashing red. Release the button, and immediately a er, tap remote button 1 once to complete the reset. The LED indicators on all buttons will flash red to confirm a successful reset.
NOTE: All previously recorded activity and custom settings will be erased from the device’s memory.
PAGE 2

IN NO EVENT SHALL ZOOZ OR ITS SUBSIDIARIES AND AFFILIATES BE LIABLE FOR ANY INDIRECT, INCIDENTAL, PUNITIVE, SPECIAL, OR CONSEQUENTIAL DAMAGES, OR DAMAGES FOR LOSS OF PROFITS, REVENUE, OR USE INCURRED BY CUSTOMER OR ANY THIRD PARTY, WHETHER IN AN ACTION IN CONTRACT, OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DA-MAGES. ZOOZ’S LIABILITY AND CUSTOMER’S EXCLUSIVE REMEDY FOR ANY CAUSE OF ACTION ARISING IN CON-NECTION WITH THIS AGREEMENT OR THE SALE OR USE OF THE PRODUCTS, WHETHER BASED ON NEGLIGENCE, STRICT LIABILITY, BREACH OF WARRANTY, BREACH OF AGREEMENT, OR EQUITABLE PRINCIPLES, IS EXPRESSLY LIMITED TO, AT ZOOZ’S OPTION, REPLACEMENT OF, OR REPAYMENT OF THE PURCHASE PRICE FOR THAT PORTION OF PRODUCTS WITH RESPECT TO WHICH DA-MAGES ARE CLAIMED. ALL CLAIMS OF ANY KIND ARISING IN CONNECTION WITH THIS AGREEMENT OR THE SALE OR USE OF PRODUCTS SHALL BE DEEMED WAIVED UNLESS MADE IN WRITING WITHIN THIRTY (30) DAYS FROM ZOOZ’S DELIVERY, OR THE DATE FIXED FOR DELI-VERY IN THE EVENT OF NONDELIVERY.
FCC NOTE THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT. STORE INDOORS WHEN NOT IN USE. SUITABLE FOR DRY LOCATIONS ONLY. DO NOT IMMERSE IN WATER. NOT FOR USE WHERE DIRECTLY EXPOSED TO WATER. This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used according

to instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in any given installation.

If this equipment causes harmful interference to radio or television reception, the user may try to correct the

interference by taking one or more of the following measures:

– Reorient or relocate receiving antenna

– Increase the separation between equipment and receiver

– Connect equipment into a separate outlet or circuit from receiver

– Consult the dealer or an experienced radio/TV technician for additional assistance

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.This

equipment should be installed and operated with minimum distance 20cm between the radiator&your body.

All brand names displayed are trademarks of their respective holders.

PAGE 3

ZEN32 WIRING DIAGRAMS FOR THE MOST COMMON 3-WAY INSTALLATIONS

For more diagrams or to request custom instructions go to support.getzooz.com

3-WAY DIAGRAM FOR 2-POINT CONTROL WITH ZEN32 AND REGULAR 3-WAY SWITCH: OPTION 1 REWIRE BOTH BOXES!

STOP!
Wire and screw position, as well as color codes are for illustration only. You should not follow the colors and positioning in the illustration blindly. Always identify all wires prior to installing Zooz switches and make sure you can match the diagrams to your set-up exactly. Don’t experiment or attempt a “trial-and-error” installation for your own safety. Don’t disconnect any wires before documenting your set-up in each box with detailed images!

NEUTRAL

ZEN32

3-WAY SWITCH

NOTE!
If you are not comfortable identifying the wiring and completing the installation, please consult a licensed electrician. Make sure you have identified all wiring correctly before connecting the switch. If your wiring doesn’t match any of the below diagrams, contact our support: [email protected]

3-WAY DIAGRAM FOR 2-POINT CONTROL WITH ZEN32 AND REGULAR 3-WAY SWITCH: OPTION 2 REWIRE BOTH BOXES!

ZEN32

3-WAY SWITCH

ON/OFF SWITCHES ONLY
Do not connect Zooz Z-Wave switches to an existing 3-way dimmer, illuminated switch, or an electronic add-on switch. Zooz switches can only be wired with mechanical on/off or momentary switches in a 3-way or 4-way setting! To simplify the diagrams, we did not include connections for the ground wire. Remember that all Zooz switches need to be wired according to the electrical code, with ground wire connected to the ground terminal.
POWER OFF!
Cut power to the circuit before handling the wiring. Diagrams and instructions in this manual are for the ZEN32 model ONLY! Always follow the correct diagram for your own safety and to avoid equipment damage. Other Zooz switches may wire differently!

ZEN32 4-WAY INSTALLATION WIRING DIAGRAM (LINE AND LOAD MUST BE IN THE SAME BOX)

CHECK 3-WAY / 4-WAY TYPE! Your 3-way and 4-way switches may have a different terminal layout so identify the in and out terminals on the 4-way switch and the common terminal on the 3-way switch before the installation.

EACH BOX NEEDS TO BE WIRED ACCORDING TO THE 4-WAY DIAGRAM.
Don’t follow the wire colors blindly – make sure you understand the role of each wire before moving forward with the installation. The colors used in this diagram are just an example of the many scenarios you’ll come across in multi-point control set-ups.

NEUTRAL
ZEN32

Follow this diagram ONLY if you confirmed you have direct connection to power and light in the same box. If they’re in separate boxes, ask us about using the ZEN32 switch with ZAC99 momentary switches in 4-way and 5-way installations.
[email protected]

LOOKING FOR ADVANCED SETTINGS? HERE THEY ARE!

Here is a selection of settings available to customize your switch: Y LED Indicator behavior, color, brightness: Y Smart Bulb Mode (disable the relay) Y On/off status for the switch a er power failure Y Auto turn-on / turn-off timer for the switch
Scan the QR code for a full list of parameters and look to the right for how to access them on your hub:

Choose your hub and scan the QR code with your phone’s camera. Then click on the link to learn how to access and change the advanced settings for the switch on your hub.

SCAN SETTINGS

Z-Box Hub

Hubitat

NEED HELP?
If you’re having trouble reading the
diagrams or don’t see your wiring set-up here, get in touch! We have more 3-way, 4-way, and 5-way diagrams and instructions. There are many ways to wire
multi-point control set-ups so unless you
can match your wiring to the diagrams
here, please don’t attempt the installation
for your own safety.
[email protected] www.support.getzooz.com

Home Assistant

SmartThings

USE IT WITH SMART BULBS!
Want to control your smart bulb from a wall switch without cutting power to it every time you turn the light off from the switch? We’ll tell you how, just ask!