Minelab Ml105 Wireless Headphone User Manual

ML105 Wireless Headphone
User Manual

ADVICE AND SAFETY INSTRUCTIONS

For complete product specification and operational guidance, read the Instruction Manual at www.minelab.com/product-manuals.
Alternatively, please contact us to make arrangements for a copy.

ASSEMBLY INSTRUCTIONS

For guidance on detector assembly, please refer to the Getting Started Guide included or visit: www.minelab.com/product-manuals.
The Minelab website also provides information on accessories available for your detector.

WARRANTY TERMS

Please refer to www.minelab.com/support/product-warranty for full warranty terms and conditions. Register your product warranty online at register.minelab.com.

SAFETY CONSIDERATIONS

• Keep out of reach of children, small parts are a choking hazard.
• Do not mutilate the batteries.
• Dispose of batteries as per local regulations.
• Only charge the detector and  accessories according to the instructions in the manual.
• Do not dispose of the detector or  accessories in a fire.
• Disconnect coil before packing/storing  as luggage.
• CAUTION — Risk of explosion if battery is replaced by an incorrect type.
• CAUTION — Only charge the battery in ambient temperatures between 0°C and 40°C.
• Headphone use at HIGH volume may cause reduced awareness of surroundings and could lead to hearing damage. Use at lower  volumes advised.
• Adult supervision required when used by children.

REGULATORY INFORMATION

Federal Communications Commission (FCC)
Statements (as applicable)
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Part 15.105
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are  designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

US Responsible Party: MINELAB AMERICAS INC, 123 Ambassador Drive, Suite 123, Naperville, IL  60540, USA
[email protected]
Compliance Statements for Canada (as applicable)
This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.
RSS-Gen notice: This device complies with Industry Canada’s license-exempt RSSs.
Operation is subject to the following two conditions:

1. This device may not cause interference; and
2. This device must accept any interference, including interference that may cause undesired operation of the device.

Modification
Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device.
Simplified EU & UKCA Declaration of Conformity Hereby, Minelab Electronics Pty Ltd declares that the radio equipment type [Refer to detectors listed in Table 1] complies with Directive 2014/53/ EU and The Radio Equipment Regulations 2017 (S.I. 2017 /1206). Full text of the EU & UKCA declarations of conformity are available at the following internet address: www.minelab.com/compliance.
EU Importer: MINELAB ELECTRONICS PTY LTD, 2 Second Avenue, Mawson Lakes, SA 5095, Australia
License / Permit
The equipment operator is responsible for investigating and obtaining any required local license or permit for metal detecting activities.
WEEE:
This symbol indicates that the equipment and its electrical accessories should not be disposed of as household garbage.
These items should not be disposed of as unsorted municipal waste and should be taken to a certified collection point for recycling and proper disposal. Refer 2012/19/EU (Waste Electrical and Electronic Equipment).

Table 1:
RADIO FREQUENCY SPECIFICATION

Table 2: CERTIFICATION SCHEME ID

* indicates use of e-labelling; follow instructions in Manual/carton to access.

Qualcomm aptX is a product of Qualcomm Technologies, Inc. and/or its subsidiaries. Qualcomm is a trademark of Qualcomm Incorporated, registered in the United States and other countries. aptX is a trademark of Qualcomm Technologies International, Ltd., registered in the United States and other countries. | The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by [Minelab Electronics Pty Ltd] is under license. Other trademarks and trade names are those of their respective owners.
Certification and logo usage dependant on product and region
Minelab Electronics, PO Box 35, Salisbury South, South Australia 5106
4901-0437-1

References

• MINELAB - Register Your Minelab
• detector de metales, detectores de oro y tesoros Detectores de metales de alto rendimiento
• Concidiones de garantía limitadas del producto Detectores de metales de alto rendimiento
• Metal Detectors | Minelab Metal Detectors
• Compliance | Minelab Metal Detectors
• Product Manuals & Guides | Knowledge Base | Minelab Metal Detectors
• Product Warranty | Minelab Metal Detectors