Lanmodo D1 Car Camera Hardwire Kit Instruction Manual

D1 Car Camera Hardwire Kit

Product Information

The LANMODO Car Camera Hardwire Kit is a special hardwire kit
designed for dash cams. It has a step-down function that can
convert 12-24V voltage to 5V/3A current to supply power to the
recorder. The kit comes with low voltage protection, short circuit
protection, over-current protection, overtemperature protection,
and reverse protection function to ensure the safety of the car and
the dash cam. The input voltage of the kit is DC12-24V, and the
output is DC5V/3A max supports 1-3A. The kit has a maximum
conversion efficiency of 96%, and its static power consumption is
about 5-10mA.

Product Usage Instructions

1. Before wiring, please test the kit.
2. Read the instructions carefully and install the kit under
   professional guidance.
3. Open the fuse box (the position of the fuse box varies slightly
   from car to car).
4. Use a power detector to detect the constant power and ACC power
   (emergency power). Connect the yellow fuse to the constant power
   source, the red fuse to the ACC power source, and the ground
   terminal (black wire) to the metal part of the body.
5. Connect the black cable of the kit to the screw or metal part
   near the fuse boxes in many cars.
6. Connect the red cable supply power only when the car engine
   starts. Testing method: The tester bulb will light when the engine
   is on and won’t light when the engine is off.
7. Plug the power cable onto your dash cam. Start the ignition and
   test if it works properly for a few minutes.
8. Hide the wire along the edge into the gap and fix the wire
   harness.

How to determine the BATT+ and ACC:

• BATT+ (yellow wire): The yellow cable should
  be connected to the fuse of the constant power supply in the car
  fuse box. If you are looking for a constant power supply in the
  fuse box: Use a voltage tester to check the fuse to ensure it still
  has electricity even if the car engine is off.
• ACC (red wire): Connect the red cable supply
  power only when the car engine starts. Testing method: The tester
  bulb will light when the engine is on and won’t light when the
  engine is off.

Note: The installation process can be quite
complicated for people who may not have experience with electrical
installations. Therefore, we recommend that customers seek the
assistance of a professional electrician or someone with experience
in electrical installations.

Installation wiring diagram
power supply
box

LANMODO
Car camera hardwire kit instruction manual
Note: Please test before wiring

Thank you for buying this product! Please read the instructions carefully and installation under a professional guide.
This product is a special hardwire kit for dash cam, with the step -down function of 12-24V voltage and step-down output 5V/3A current, supplying power to the recorder.
Product parameters features:
With low voltage protection function, the equipment will automatically detect the battery voltage. When the voltage is too low, it can automatically cut off the power supply to ensure that the car can start normally. Its functions include short circuit protection, over-current protection, overtemperature protection, and reverse protection function.
. Input voltage: DC12-24V
Output: DC5V/3A max supports 1-3A
Low voltage protection: 12V(11.8V); 24 V(23.6 V)
Conversion efficiency: Maximum value: 96%
Static power consumption: about 5-10mA
Operating temperature: industrial -20°C~+60°C

Installation drawing

Black=GND(-) yellow=BAT(+) Red=ACC

Low voltage protection parameter
12V- 11.8V 24-23.6V Connection recorder

Installation Procedure
1. Open the fuse box (The position of the fuse box varies slightly from car to car)

3. This black cable is connected to the metal parts of the vehicle. There are screw nails and metal parts near the fuse boxes in many cars. Connect the black cable to the screw or metal part.

7.Close the fuse box – Done

2. Use a power detector to detect the constant power and ACC power (emergency power). Connect the yellow fuse to the constant power source, the red fuse to the ACC power source, and the ground terminal (black wire) to the metal part of the body.

4. Plug the power cable on to your dash cam. Starts the ignition and tests if it works properly for a few minutes.
5. Then hide the wire along the edge into the gap and fix the wire harness.

How to determine the BATT+ and ACC.

BATT+ (yellow wire)

The yellow cable should be connected to the fuse of the

constant power supply in the car fuse box. If you are looking

for a constant power supply in the fuse box: Use a voltage

tester to check the fuse to ensure it still has electricity even if the car engine is off. The ACC (red wire)

6. Wire harness edge clamp into seam with tool (side seam)

Connect the red cable supply power only when the car engine

starts. Testing method: The tester bulb will light when the

engine is on and won’t light when the engine is off.

Note: The installation process can be quite complicated for people who may not have experience with electrical installations. Therefore, we recommend that customers seek the assistance of a professional electrician or someone with experience in electrical installations.