Matin Floor Lamp
Product Information
The Matin Floor is a lamp that features an integrated LED module
with a power output of 10W and a color temperature of warm white
(2800K). The LED module has an expected lifespan of 25,000 hours.
When the light source reaches the end of its life, the entire
luminaire should be replaced. The lamp is designed for indoor use
only.
Technical Data:
- Fitting Type: Integrated LED
- Power: 10W
- Color Temperature: Warm white
- Lumens: 200-300
Care and Maintenance:
Hay recommends the following care and maintenance practices for
the Matin Floor lamp:
- Do not use wet or damp cloths for cleaning the shade. Instead,
use a dry, lint-free cloth or duster to remove any dirt. - The frame can be cleaned with a soft damp cloth and mild
detergent. Do not use alcohol or any other solvents to clean the
product. - The external flexible cable or cord of the luminaire cannot be
replaced. If the cord is damaged, the luminaire should be
destroyed. - Ensure that the power supply has been turned off before
cleaning the product.
Please note that Hay will not accept responsibility for any
accidents, injuries, or damages that occur due to the use of
incorrect bulbs. Additionally, in some countries, electrical
installation must be carried out by authorized
electricians/contractors. Please check with your local authority
for guidance. The product must not be modified in any way, and Hay
accepts no responsibility for any products that have been modified
or tampered with.
Product Usage Instructions
- Unpack all the parts and check that you have received all the
parts listed. - Slide the bottom stem onto the base.
- Insert one of the set screws into the back of the bottom
connecting piece and screw it firmly in place using the supplied
tool. - Slide the top stem onto the bottom stem.
- Insert the set screw into the back of the central connecting
piece and screw it firmly in place using the supplied tool. - Screw the top screw into the top cap, but do not fully tighten
it yet. - Clip the cable into the cable clip located on the stem and in
the groove on the back of the central connecting piece and the
bottom connecting piece. - Remove the shade from its packaging and spread out the bottom
while simultaneously pushing it down over the top screw, so that it
rests on top of the top cap. Gently push the top of the pleated
shade underneath the top screw, so that it is wedged between the
top screw and top cap. - Once the shade is in place, gently adjust the pleats at the top
so they are evenly spread out. Once adjusted, fully tighten the top
screw. - Plug the trailing cable into the power supply and attach the
correct adapter for your region. The lamp is now ready to use.
The lamp’s inline switch has a three-step dimmable feature. The
first push sets the lamp to maximum brightness, the second push to
medium brightness, and the third push to lowest brightness. The
fourth push turns off the lamp.
INSTRUCTION MANUAL
MATIN FLOOR
DESIGN BY INGA SEMPÉ
GENERAL INFORMATION
TECHNICAL DATA
CARE AND MAINTENANCE
This product is supplied with an integrated LED module (2800K warm white, 200-300 lumens). The expected lifespan of the LED modules is 25,000 hours. When the light source reaches its end of life, the whole luminaire should be replaced.
FITTING TYPE | Integrated LED POWER (W) | 10W COLOUR TEMPERATURE | Warm white
HAY will not accept any responsibility for any accidents, injuries or damages that occur due to the use of incorrect bulbs.
Do not use wet or damp cloths for cleaning and maintaining the shade. Please use a dry, lint-free cloth or duster to remove any dirt. The frame can be cleaned with a soft damp cloth and mild detergent. Do not use alcohol or any other solvents to clean the product. The external flexible cable or cord of this luminaire cannot be replaced; if the cord is damaged, the luminaire should be destroyed. Ensure that the power supply has been turned OFF before cleaning the product.
ATTENTION
In some countries, electrical installation must be carried out by authorised electricians/contractors; please check with your local authority for guidance. The product must not be modified in any way. HAY accepts no responsibility for any products that have been modified or tampered with. This lamp is designed for indoor use only.
Top screw
PARTS
Shade
Allen key
Top stem
Set screws
Bottom stem
Inline switch
Base
Power supply adapter
1. Unpack all the parts and check that you have received all the parts listed.
Slide the bottom stem onto the base, as shown below.
2. Insert one of the set screws into the back of the bottom connecting piece and screw it firmly in place, using the supplied tool. You will find the set screws and tool
in the small fitting bag.
3. Slide the top stem onto the bottom stem, as shown below.
4.
Insert the set screw into the back of the central connecting piece and screw it firmly in place, using the supplied tool.
5.
Screw the top screw into the top cap, as shown below. Do not fully screw it in place yet.
6.
Clip the cable into the cable clip, which is located on the stem, and in the groove on the back of the central connecting piece and the bottom
connecting piece.
7.
Remove the shade from its packaging and spread out the bottom while simultaneously pushing it down over the top screw, so that it rests on top of
the top cap. Gently push the top of the pleated shade underneath the top screw, so that it is wedged between the top screw and top cap.
8.
Once the shade is in place, gently adjust the pleats at the top so they are evenly spread out, as shown below. Once the shade is as illustrated,
the top screw can be fully tightened.
9.
Plug the trailing cable into the power supply. Attach the correct adapter for your region. The lamp is now ready to use.
10.
The lamp’s inline switch has a three-step dimmable feature. The first push sets the lamp to maximum brightness, the second push to medium brightness and the third
push to lowest brightness. The fourth push turns the lamp off.
40%
100%
70%
CARE & MAINTENANCE
Our Care & Maintenance offers guidance for optimal maintenance of your HAY product. It includes advice and instructions on cleaning and caring for specific
materials to prolong the life of your lighting.
Please find our Care & Maintenance guide by scanning the QR code
You can find more relevant information on Matin Floor by scanning the QR code
You can also find the same information here hay.dk/downloads
10/01/2023
Havnen 1 8700 Horsens Denmark +45 3164 6000 / [email protected]
www.hay.com
HAY.dk – latest products, designer news and retailer info
HAY - Danish-Inspired Furniture and Accessories For Modern Living
VOCAST Digital Showroom
