JLAB JBUDS Air True Wireless Earbuds User Manual
JLAB JBUDS Air True Wireless Earbuds User Manual
FIRST TIME SETUP
- AUTO-CONNECTING EARBUDS
Press and hold both touch sensors 3+ seconds to power ON.
One earbud turns solid white and the other earbud blinks blue/white indicating ready to pair to your device. 
CONNECTING TO BLUETOOTH
Select “JLab JBuds Air” in your device settings.
Voice prompt “Bluetooth connected” followed by solid white lights will indicate you are connected.
CONNECTING TO BLUETOOTH
ADDING NEW / ADDITIONAL BLUETOOTH DEVICES:
Turn OFF Bluetooth from any previously connected device. Turn ON Bluetooth from new device. Take earbuds out of the case.
Earbuds will automatically enter Bluetooth Pairing. Select “JLab JBuds Air” in new device settings to connect.
| VOLUME DOWN: Single tap SIRI (iOS) or “OK GOOGLE” (ANDROID): Double tap ANSWER: Single tap HANGUP: Double tap REJECT INCOMING CALLS: Press & hold 1+ sec TRACK BACK: Press & hold 1+ sec TURN ON: Press & hold 3+ sec CHANGE EQ: Triple tap (JBuds Air will cycle 3 EQ settings) | VOLUME UP: Single tap ANSWER: Single tap HANGUP: Double tap REJECT INCOMING CALLS: Press & hold 1+ sec PLAY / PAUSE: Double tap TRACK FORWARD: Press & hold 1+ sec TURN ON: Press & hold 3+ sec CHANGE EQ: Triple tap (JBuds Air will cycle 3 EQ settings) |
TURN OFF EARBUDS WITHOUT CHARGING CASE:
Enter your Bluetooth device settings and disconnect the JBuds Air. Earbuds will power OFF after 3 minutes.
VOICE PROMPTS
“Ready to Pair”: JBuds Air are ready to pair to Bluetooth device
“Bluetooth Connected”: Earbud is connected to device
“Battery Full”: 100-75%
“Battery Medium”: 75-20%
“Low Battery”: Less than 25%
When power decreases to 10%, “Low Battery” will play
CUSTOM EQ3 SOUND MODES
Tap either the right or left earbud 3 times for different EQ settings (JBuds Air will cycle 3 EQ settings).
 |  JLab SIGNATUREJLab C3™ signature sound with amplified bass and vocals |  BALANCEDEven sound with no additional enhancements |  BASS BOOSTAmplified bass and sub-bass |
CHARGING EARBUDS
- Match the corresponding L and R letters on the charging case for proper charging. The earbuds will auto power OFF and start charging. 1 Blue lights will indicate earbuds are charging and will turn OFF when fully charged.
- Earbuds will auto power ON and reconnect to your device when taken out of the case.
CHARGING CASE
Connect the JBuds Air to computer or USB 5V 1A (or less) output device.
LEDs pulse white when charging and turn solid white when fully charged.
FITTING
Try all the optional Cush Fins and ear tips for best fit and proper seal.
The Cush Fin should be aligned by positioning the contour around the microphone hole.
TROUBLESHOOTING
NO AUDIO IN ONE EARBUD (MANUAL RESET)
- Enter your Bluetooth device settings and forget the JBuds Air.
- Open the charging case door and leave both earbuds inside. Starting with ONE earbud, quickly press the button 7x times. Light will blink blue 4x times. Leave the earbuds in the charging case.
- Repeat with the other earbud.
Quickly press the button 7x times. Light will blink blue 4x times.
- Take both earbuds out of the charging case. Wait for one of the earbuds to turn solid white and one to blink blue/white. You are now ready to pair to your Bluetooth device.
Instructional videos at: JLAB.COM/MANUALS
TROUBLESHOOTING
BLUETOOTH DEVICE DOES NOT CONNECT / RECONNECT
- Enter your Bluetooth device settings and forget the JBuds Air.
- On your device, turn OFF then ON Bluetooth.
- Open the charging case and wait for one earbud to turn solid white and one to blink blue/white.
- Select “JLab JBuds Air” in device settings to reconnect.
ECHOES ON CALLS
If you experience microphone echo/call quality with the JBuds Air, make sure the Cush Fin is not blocking the microphone port.
QUICK TIPS
- Fully dry off the earbuds before putting in the charging case to avoid any damage to the case. The earbuds are sweat/water resistant but the case is not.
- Either earbud can connect to your device and be used independently. Simply take out the earbud from the charging case and it will auto-connect.
- Choosing the correct ear tip makes a significant improvement in audio quality due to the proper seal for the driver. Try all ear tips for the best results.
WARNING
Fully dry off the earbuds before putting them in the charging case to avoid any damage to the case.
The earbuds are sweat/water resistant but the case is not.
CAUTIONS
- Avoid extreme heat, cold, and humidity.
- Avoid dropping or crushing the earbuds.
- Wax may build up in the earbud tips, lowering the sound quality.
Carefully remove the wax with a cotton swab or other small tool to improve the sound quality. - If you experience discomfort or pain, try lowering the volume or discontinuing use temporarily.
- If you experience regular discomfort while using this product, discontinue use and consult your physician.
- We recommend you treat your earbuds as you would a nice pair of sunglasses and keep them in a safe location when not in use.
Shop products | Product alerts | Burn-in your headphones
JLab Store + Burn-in Tool
To expand on the previous reply, the answer is “yes, but.” The right earbud is the bud that receives the Bluetooth signal from your source. It then retransmits the signal to the left bud. So, if you want to use only the right bud and keep the left bud in its charging case, that will work fine as long as you stay within Bluetooth range of your source. But if you want to use only the left bud, you have to keep the right bud out of the case, turned on and within range of both your source and the left bud. If you put the right bud in its case, it will automagically turn off, cutting off the signal to the left bud.
For listening to just music, the sound is fine. But watching videos with the latency of like (I’m guessing here) .25 seconds, it get’s noticeable and annoying to watch. On some videos, there’s just a slight delay of someone’s mouth moving and sound catching up with it. On other videos, the mouth has already finished a word and starting the next word and the sound is just playing the first word. I bought this to listen to music and watch videos but I guess I’ll just be using it for music since it’s cheap.
They work with bluetooth enabled devices. So yes they work with android. Not sure what your question is about concerning Amazon alexa
Yes
It clearly states in the instruction manual that only the right side will work during a phone call. That is probably to keep people from wearing them while driving.
Make sure the buds are in the proper slots left and right. If the problem persists, contact customer support.
Touch button only
They’re not going to give you noise canceling like big headphones that surround your ears, but I’ve found that the Cloud foam tips also available from JLAB will block out a good amount of sound and enhance the music sound, especially bass.
Yes
Three taps on either earbud should switch consecutively between the 3 equalization modes, but often, not all 3 register. Both the positioning of the tap and the timing are critical.
Yes, as long as the computer has Bluetooth.
No
The earbuds give you a vocal auditory conformation (a female voice) which tells you which setting is currently on at the moment where you changed that setting.
Volume is independent of phone volume
VIDEO
We love that you are rocking JLab!
We take pride in our products and fully stand behind them.
YOUR WARRANTY
All warranty claims are subject to JLab authorization and at our sole discretion. Retain your proof of purchase to ensure warranty coverage.
CONTACT US
Reach out to us at [email protected] or visit jlab.com/contact
REGISTER TODAY
jlab.com/register
Product updates | How-to tips
FAQs & more
