TX80 Urba One
Product Information
The product is the TX80 Urba / TX80 Urba One taximeter
manufactured by INTERFACOM, S.A.U. It is a device used in taxis to
calculate fares based on distance traveled and time taken during a
trip. The taximeter has various features and functions that enable
the user to accurately calculate and display the fare amount.
Product Usage Instructions
- Switching the Taximeter On/Off:
To turn on the taximeter, press the “O” key. If a password is
required, enter the code when prompted. Once the correct code is
entered, the taximeter will turn on. To turn off the taximeter,
press the “O” key again. - Trip Sequence:
When in the hired position, press keys 1, 2, 3, or 4 to start
the right tariff. For tariffs 5, 6, 7, and 8, first press the “*”
key and then press keys 1, 2, 3, or 4. To exit the extras sequence,
press the “#” key. - Adding Extras in Hired Position:
To add extras to the fare in the hired position, press keys 1,
2, 3, or 4. For extras 5, 6, 7, and 8, first press the “*” key and
then press keys 1, 2, 3, or 4. To exit the extras sequence, press
the “#” key. - Stopped Position:
Press the “#” key to go to the stopped position.
- Entering Extras in Stopped Position:
To add extras in the stopped position, press keys 1, 2, 3, or 4.
For extras 5, 6, 7, and 8, press the “*” key and then press keys 1,
2, 3, or 4. To exit the extras sequence, press the “#” key. - Adding Extras to the Fare:
To add the extras to the fare amount, press the “+” key. The
extras will be added for 5 seconds and then the fare amount will
break down again into fare and extras. - Cancellation of Manual Extras:
To cancel manual extras, press the “*” key and then press the
“#” key. The manual extras will be erased. It is possible to add
extras again if necessary. This function may not be available in
all markets. - End Trip:
To end a trip, press the “O” key. The status will blink for a
few seconds until the taximeter switches to “FOR HIRE”. - Print a Ticket:
To print a trip receipt, press the “+” key while the status
indication is blinking. Copies of the receipt can be printed by
pressing the “+” key again. Press the “O” key to go back to “FOR
HIRE”. - Going Back to FOR HIRE:
The taximeter will automatically go back to “FOR HIRE” after a
few seconds. - Display Last Trip Data:
While in “FOR HIRE”, press the “+” key to display the following
data successively:- Total fare amount
- Total distance traveled
- Total time taken
- Start time of the trip
- End time of the trip
INTERFACOM, S.A.U.
TX80 Urba / TX80 Urba One
USER’S MANUAL
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
1
INTERFACOM, S.A.U.
INDEX 1. TRIP SEQUENCE …………………………………………………………………………………………………………………………. 4
1.1. HIRED POSITION …………………………………………………………………………………………………………………. 4 1.2. ADDING EXTRAS IN HIRED ……………………………………………………………………………………………………. 4 1.3. STOPPED POSITION …………………………………………………………………………………………………………….. 4 1.4. ENTERING EXTRAS IN STOPPED …………………………………………………………………………………………….. 5 1.5. ADDING THE EXTRAS TO THE FARE ……………………………………………………………………………………….. 5 1.6. CANCELLATION OF MANUAL EXTRAS …………………………………………………………………………………….. 5 1.7. END TRIP ……………………………………………………………………………………………………………………………. 6 1.8. PRINT A TICKET …………………………………………………………………………………………………………………… 6 1.9. GOING BACK TO FOR HIRE……………………………………………………………………………………………………. 6 2. DISPLAY LAST TRIP DATA …………………………………………………………………………………………………………….. 7 3. TOTALIZERS SEQUENCE ………………………………………………………………………………………………………………. 8 3.1. ACCUMULATIVE TOTALIZERS………………………………………………………………………………………………… 8 3.2. DAILY TOTALIZERS ………………………………………………………………………………………………………………. 9 3.3. CLEARING DAILY TOTALS ……………………………………………………………………………………………………… 9 4. FOR HIRE MENU ………………………………………………………………………………………………………………………. 10 4.1. SHIFT OPENING…………………………………………………………………………………………………………………. 10
4.1.1. TURN OFF………………………………………………………………………………………………………………….. 11 5. ANCILLARY FUNCTIONS IN FOR HIRE…………………………………………………………………………………………… 11
5.1. ROOFLIGHT ON/OFF ………………………………………………………………………………………………………….. 11 5.2. SETTINGS SEQUENCE …………………………………………………………………………………………………………. 11
5.2.1. DATE AND TIME VISUALIZATION ………………………………………………………………………………….. 12 5.2.2. VOLUME……………………………………………………………………………………………………………………. 14 5.2.3. TEST SEQUENCE …………………………………………………………………………………………………………. 14 5.2.4. TAXIMETER CONTROL BLOCKS VISUALIZATION ……………………………………………………………… 15 7.4.6. SKYGLASS CONTROL BLOCKS VISUALIZATION ………………………………………………………………… 19 7.4.7. LANGUAGE SETTINGS …………………………………………………………………………………………………. 20 7.4.8. TEST LUMINOSO EXTERNO ………………………………………………………………………………………….. 21 6. ERROR MESSAGES ……………………………………………………………………………………………………………………. 22
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
2
SWITCHING THE TAXIMETER ON. Taximeter OFF.
INTERFACOM, S.A.U.
Press the O key to turn the Taximeter ON. If a password is required, the second point in the status display will blink, waiting for the introduction of the code.
If no password is required, or once the correct code is entered, the taximeter goes to ON.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
3
1. TRIP SEQUENCE 1.1. HIRED POSITION
Press 1 , 2 , 3 or 4 key to start the right tariff.
INTERFACOM, S.A.U.
For tariffs 5, 6, 7 and 8, first press the key, and then press key 1 , 2 , 3 or 4 .
1.2. ADDING EXTRAS IN HIRED By pressing key the text HIRED will start flashing.
Add the extras by pressing keys 1, 2, 3 or 4. For extras 5, 6, 7 and 8, first press the key, and then
press keys 1, 2, 3 or 4.
To exit the extras sequence press key .
1.3. STOPPED POSITION Press key to go to the Stopped position
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
4
INTERFACOM, S.A.U.
1.4. ENTERING EXTRAS IN STOPPED
By pressing key the text STOPPED will start flashing.
Add the extras by pressing keys 1, 2, 3 or 4. For extras 5, 6, 7 and 8, press the key, and then press
key 1, 2, 3 or 4.
To exit the extras sequence press key .
1.5. ADDING THE EXTRAS TO THE FARE
Pressing + key adds the extras to the fare amount for 5 seconds. After this time, this amount will
break down again into fare and extras.
1.6. CANCELLATION OF MANUAL EXTRAS
Press the key, and then press the
key. The manual Extras will be erased. It is possible to add Extras
again if necessary. This function is optional, and may not be available to all markets.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
5
INTERFACOM, S.A.U. 1.7. END TRIP
By pressing O key . The status will start to blink for some seconds, until the taximeter switches to
FOR HIRE. 1.8. PRINT A TICKET
By pressing + while the status indication is blinking, the trip receipt will be printed. Copies of the receipt can be printed by pressing + key again.
Press O to go back to FOR HIRE.
1.9. GOING BACK TO FOR HIRE The taximeter will go back to FOR HIRE automatically after a few seconds.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
6
INTERFACOM, S.A.U.
2. DISPLAY LAST TRIP DATA Only works when the car is stopped.
While in FOR HIRE, press the + key. The taximeter will show the following data successively:
– The Fare amount and the Extras
– The duration of the trip: Hours and minutes.
– The trip distance in kilometers.
Press the + key to print the receipt of the last trip.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
7
3. TOTALIZERS SEQUENCE Only works when the car is stopped.
3.1. ACCUMULATIVE TOTALIZERS
By pressing
key the first totalizer is shown.
INTERFACOM, S.A.U.
Press + key to print the totalizers.
By pressing again key the next figures of the total will be displayed. The totalizers sequence can
be aborted at any moment by pressing the O key.
After few seconds, if the
key is not pressed, it switches to the next total, following the next list.
– 1 Nr. of trips – 2 Fare amount – 3 Extras amount – 4 Total amount – 5 Total distance (km) – 6 Distance in Hired (km) – 7 Distance in For Hire (km) – 8 Time in hired (hours) – 9 Time in ON (hours) – A Nr. of daily totalizers cancellations
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
8
INTERFACOM, S.A.U.
3.2. DAILY TOTALIZERS
After the accumulated totalizers, the daily totalizers are showed by continuing pressing the key according to the next list.
Press + key to print the totalizers.
By pressing again key the next figures of the total will be displayed. The totalizers sequence can
be aborted at any moment by pressing the key O.
– 1. Nr. of trips – 2. Fare amount – 3. Extras amount – 4. Total amount – 5. Total distance (km) – 6. Distance in Hired (km) – 7. Distance in For Hire (km) – 8. Time in hired (hours) – 9. Time in ON (hours)
3.3. CLEARING DAILY TOTALS
While the totalizer is showed, press key.
Enter the password with the 1, 2, 3 y 4 keys to change each of the four positions, and press the
key to confirm. Key 1 increases the thousands, key 2 increases the hundreds, key 3 increases the tens and key 4 increases the units. If the code is correct, it will sound two short “beeps”. Otherwise, it will sound a loud long “beep”.
Once the totals cancellation is done, the taximeter will go back to FOR HIRE.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
9
4. FOR HIRE MENU In FOR HIRE, by pressing the O key you access to the FOR HIRE MENU.
INTERFACOM, S.A.U.
4.1. SHIFT OPENING Press the key to put the taximeter in closed shift, then press the O key to open shift.
Enter the Driver number changing the numbers using the 1, 2, 3 y 4 keys. Press the key.
Enter the Password number changing the numbers using the 1, 2, 3 y 4 keys. Press the key.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
10
INTERFACOM, S.A.U. If it is not a valid user/password pair, shift opening is rejected and the taximeter will return to closed shift.
To close shift, press the O key and then the key.
4.1.1. TURN OFF If there is no interaction with the taximeter in the closed shift state, it turns OFF after a few seconds. It turns to shift closed again pressing the O key, or when the vehicle starts to move.
5. ANCILLARY FUNCTIONS IN FOR HIRE
5.1. ROOFLIGHT ON/OFF
By pressing key and then + key the rooflight will toggle between ON and OFF. When the rooflight
is switched the icon will appear near the FOR HIRE.
5.2. SETTINGS SEQUENCE Only available when the car is stopped.
By pressing key twice, the different settings options are shown. By pressing + key the printer makes a page feed.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
11
5.2.1. DATE AND TIME VISUALIZATION The display of date and time is the first option shown.
INTERFACOM, S.A.U.
By pressing
key if shift control enabled, the remaining time and the available breaks will appear.
If the shift control is not enabled, it will directly show the time.
By pressing O key it switches to FOR HIRE.
By pressing
key again or after few seconds the time is displayed.
By pressing O key it switches to FOR HIRE.
By pressing
key again or after few seconds the date is displayed.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
12
INTERFACOM, S.A.U.
By pressing O key it switches to FOR HIRE.
By pressing
key again or after few seconds the year is displayed.
By pressing O key or after few seconds it switches to FOR HIRE.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
13
5.2.2. VOLUME
By pressing key after light setting.
INTERFACOM, S.A.U.
By pressing intensity.
key to set the volume of the beep. The circular indicator shows the selected
By pressing + changes the beep mode.
By pressing O key it switches to FOR HIRE.
5.2.3. TEST SEQUENCE
By pressing key after volume setting.
Press key
to display the test sequence. (0,1, …,9).
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
14
INTERFACOM, S.A.U.
By pressing O key or after few seconds it switches to FOR HIRE.
5.2.4. TAXIMETER CONTROL BLOCKS VISUALIZATION
By pressing key after test sequence.
By pressing O key or after few seconds it switches to FOR HIRE.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
15
7.4.5.1. BLOCK 1 VISUALIZATION C.1 Displays the current K Constant.
INTERFACOM, S.A.U.
Press
key for going to the next visualization or it goes automatically after few seconds:
– C.1 Current “K” constant
– C.2 Tariff serial number
– C.3 Tariff recording date (Y.MM.DD)
– C.4 Agent’s code
– C.5 Tariff checksum
– C.6 Ticket identification control number.
– C.7 Pre-change tariff activation date
– C.8 Pre-change tariff checksum.
– C.9 Nr. of constant «K» changes
– C.A Nr. of tariff changes
– C.b Firmware TX80 Software Checksum
In case the shift control is set: – C.C Shift duration on weekdays – C.d Shift duration on weekends and holidays – C.E Remaining time of the current shift
Press + key to print the control blocks.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
16
7.4.5.2. BLOCK 2 VISUALIZATION L.1 Car License number.
INTERFACOM, S.A.U.
Press
key to go to the next visualization. The data displayed in block 2 are the following:
– L.1 Car License number
– L.2 Board serial number
– L.3 Manufacturing date (YYMMDD).
– L.6 Program version
Press + key to print the control blocks.
7.4.5.3. BLOCK 3 VISUALIZATION I.1 State led tariff 1 indication
Press
key for going to the next visualization or it goes automatically after few seconds.
The data displayed in the block 3 are the following:
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
17
INTERFACOM, S.A.U. – I.1 State led tariff indication – b.1 Flag drop – M.1 Meters first drop – S.1 Seconds firs drop – d.1 Price per km – H.1 Price per hour – P.1 Price per km in stopped position – E.1 Extras amount assigned to these tariff
Press + key to print the control blocks.
In case of more tariffs, the same data of block 3 is shown below for each of the remaining tariffs, that is:
I.2 State led tariff 2 indication
Once the blocks visualization is finished, parameters of the versions are shown.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
18
INTERFACOM, S.A.U.
– Pr Date of the update and taximeter version – Pr User who updated it and checksum – tF Date of the update and tariff – C Date of the update and constant – Po Date and time of power failures. Once the blocks visualization is finished, the taximeter goes to for hire automatically.
The sequence can be aborted at any time by pressing the O key.
7.4.6. SKYGLASS CONTROL BLOCKS VISUALIZATION
By pressing key after taximeter control blocks visualization.
By pressing O key or after few seconds it switches to FOR HIRE.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
19
7.4.6.1. BLOCKS VISUALIZATION E.1 Serial number.
INTERFACOM, S.A.U.
Press
key to go to the next visualization, or automatically after few seconds:
– E.1 Skyglass serial number – E.2 Software version – E.3 Hardware version – E.4 Checksum
Press + key to print the control blocks.
Once the blocks visualization is completed, the taximeter goes to for hire automatically.
The sequence can be aborted at any time by pressing the key O.
7.4.7. LANGUAGE SETTINGS
By pressing key after Skyglass control blocks visualization.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
20
By pressing O key or after few seconds it switches to FOR HIRE.
By pressing
key to select the language.
7.4.8. TEST LUMINOSO EXTERNO
By pressing key after language settings visualization.
INTERFACOM, S.A.U.
By pressing O key or , or after few seconds it switches to FOR HIRE.
By pressing the key, it is shown whether the bulb lights work rights or not showing an 8 at the right bulbs and a white space at bulbs which work wrong. For example:
In this case, the bulb lights that are working ok are the 1,2,4 and 5. The bulb light number 3 is not working.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
21
6. ERROR MESSAGES
INTERFACOM, S.A.U.
The possible error messages that may appear on the display are listed below.
– E-2 Roof lights failure: The roof lights are not correctly connected or some of its bulb lights doesn’t work. This error is shown if it is enabled in the tariff.
– E-5 The taximeter is out of the configured revision period: This message is shown when the taximeter is out of the configured revision period. It is resolved by setting a new stop date or disabling it.
– E-6 Excess speeding. This error is shown if it is enabled in the tariff. – E-7 Working time max exceeded: This error is shown when the hours of the shift have
finished. The error automatically disappears when you restart the day. – E-8 Error in the tariff parameters: The taximeter has not the tariff loaded, or the tariff loaded
is wrong. The error is solved by charging tariff. – E-10 Printer failure: The printer is not working, is incorrectly connected or has no paper. This
error is shown if it is enabled in the tariff. – E-11 Serial number error: This error is displayed if the serial numbers are not linked. The
error is solved by charging tariff. – E-12 RAM memory loss: This error is displayed if the device has a depleted battery or there
is a malfunction. The error is solved by replacing the internal battery of the equipment. – E-Z Anti Zapper error: A distance pulse error detected. This error is shown if it is enabled
in the tariff. The error is solved by charging tariff. – E-NS Serial Number Pairing Error: This error is displayed when a TX80 is connected to a
device to which it is not paired. This pairing is done when charging tariff.
TX80 TX80 Urba_TX80 Urba One_EN.002.docx
22
