A04729BK 28.5-in 4 Light Matte Black and Clear Glass LED Modern Contemporary Vanity Light Bar
Product Information
Item Number: A04729BK
Maximum Wattage: Type A, Max 60W per bulb
Contact Information: +1 850 296 2377, Working
hours: Mon-Fri 9:00 a.m. – 16:00 p.m. EST, Email:
[email protected]
Product Usage Instructions
WARNING (To reduce the risk of fire, electric shock, or
personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may
need it at a later time. - Before you start, NEVER attempt any work without shutting off
the electricity until the work is done. - Mounting surface should be clean, dry, flat, strong enough and
1/4 larger than the canopy on all sides. Any gaps between the
mounting surface and canopy exceeding 3/16 should be corrected as
required. - Make sure that the ceiling or wall can stand the weight of the
lamp before installation. - Make sure the voltage you are using is 120V. The maximum
wattage is Type A, Max 60W per bulb. - Keep the lamp away from acidic and alkaline substances in case
of damaging the surface of the lamp. - When replacing bulbs, you should turn off or unplug the lamp
and you must wait until it is cool as bulbs get hot quickly. - The safety instructions appearing in this manual are not meant
to cover all possible conditions that may occur. It must be
understood that common sense, caution, and care must be used with
any electrical products.
Tools Required (Not Included):
Before starting assembly and installation, please prepare the
needed tools as shown in the picture.
Parts Included:
- (C) Green ground screw (1)
- (D) Mounting plate (1)
- (E) Back plate (1)
- (F) Knob nut (2)
- (G) Socket (4)
- (H) Screw (12)
- (I) Glass shade (4)
Accessories Enclosed:
- (A) Mounting screw (2)
- (B) Plastic wire connector (3)
Assembly & Installation Instructions:
- Carefully remove the fixture from the carton and check that all
parts and accessories are included as shown in the above
illustration. - Turn off power. Before you start the installation, NEVER
attempt any work without shutting off the electricity until the
work is done. - Secure mounting plate (D) to the outlet box with mounting
screws (A). - Connect wires according to the provided chart. Twist wires
together with plastic wire connectors until tightly joined, and
wrap each connector with approved electrical tape. Be sure that no
wire strands are exposed and then carefully tuck all wires into the
outlet box. - Attach back plate (E) to mounting plate (D) with the previously
removed knob nuts (F). Hand tighten until snug. - Carefully place glass shades (I) on sockets (G), and secure
them with screws (H). - Install bulbs (not included). Please do not exceed the maximum
wattage recommended on the socket. - Check that everything is installed properly, then you can turn
on the light. Enjoy!
Ordering Parts:
Keep this sheet for future reference in case you need to order
replacement parts. All parts for this fixture can be ordered from
the place of purchase. Be sure to use exact wording from the
illustration when ordering parts.
+1 850 296 2377 Working hours : Mon Fri 9:00 a.m. 16:00 p.m. EST
Item Number: A04729BK
WARNING (To reduce the risk of fire, electric shock, or personal injury):
1. We suggest installation by a licensed electrician. 2. Please read the instruction carefully and save it as you may need it at a later time.
3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
4. Mounting surface should be clean, dry, flat, strong enough and 1/4″ larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16″ should be corrected as required.
5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.
6. Make sure the voltage you are using is 120V. The maximum wattage is Type A,Max 60W per bulb. 7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT:
TOOLS REQUIRED (NOT INCLUDED): Before starting assembly and installation please prepare the needed tools as below picture
Page: 1 / 3
+1 850 296 2377 Working hours : Mon Fri 9:00 a.m. 16:00 p.m. EST
PARTS INCLUDING: (C) Green ground screw (1) (D) Mounting plate (1) (E) Back plate (1) (F) Knob nut (2) (G) Socket (4) (H) Screw (12) (I) Glass shade (4)
ACCESSORIES ENCLOSED: (A) Mounting screw (2) (B) Plastic wire connector (3)
ASSEMBLY & INSTALLATION INSTRUCTIONS: 1. Carefully remove the fixture from the carton and check that all parts and accessories are
included as shown in the above illustration. 2. Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
» Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
» Place the wall switch in the “OFF” position.
3. Make assembly
Page: 2 / 3
+1 850 296 2377 Working hours : Mon Fri 9:00 a.m. 16:00 p.m. EST
Step A1 » Unscrew knob nuts (F) from back plate (E), then set them aside for later installation. Step A2 » Carefully pass the supply wires from the outlet box through mounting plate (D).
Secure mounting plate (D) to the outlet box with mounting screws (A).
Step A3 » Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart
Connect wires according to the below chart
Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step A4 » Align the holes in back plate (E) with the preassembled mounting screws, then attach back plate
(E) to mounting plate (D) with the previously removed knob nuts (F). Hand tighten until snug.
NOTE: back plate (E) should be snug against the wall with knob nuts (F). If not, remove back plate (E), adjust the threaded length of preassembled mounting screws on mounting plate assembly (D): · first, unscrew the preassembled hex nuts · then, screw the preassembled mounting screws in or out of mounting
plate (D) · when the secure length is achieved, tighten the preassembled hex nuts
and back to Step A4.
Step A5 » 1) Unscrew screws (H) from sockets (G).
Carefully place glass shades (I) on sockets (G), and secure them with screws (H). 2) Install bulbs (Not included) (Please do not exceed the maximum wattage recommended on the
socket.)
4. Check everything is installed properly, then you could turn on the light. Enjoy!
ORDERING PARTS
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
CLEANING
To clean, wipe the fixture with a soft cloth. Clean glass with a mild cleaner (such as mild and nonabrasive soap). Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
Page: 3 / 3
