2A583-MFREADER MFREADER Semiconductor RFID Multi-Function Reader
Product Information
The Brillian RFID System is a multi-function reader (MF Reader)
manufactured and published by Brillian Network & Automation
Integrated System Co., Ltd. The company is located at No.41, Keyi
St., Zhunan Township, Miaoli County 350, Taiwan, R.O.C. They can be
reached at Tel: 886-37-580708, Fax: 886-37-580728, Email:
[email protected], and their website is
http://www.brillian.com.tw.
This user manual is the property of Brillian and prohibits any
reproduction or distribution of its contents without the expressed
written consent of the company. It is also prohibited to copy or
use the software for other purposes or distribute it to third
parties. Violators will be held liable for damage.
Product Usage Instructions
The Brillian CIDRW (Carrier ID Reader/Writer) is an RFID system
used to read and write information from transponders (tags)
attached to goods. Follow the steps below for basic setup:
- Attach a transponder (tag) to the goods you want to get
information from. The transponder contains a data record for the
goods. - Connect the CIDRW to a host computer using an RS232
connection. - The host computer can send an order message to the CIDRW.
- The CIDRW will use radio frequency to read the goods
information from the transponder and send it back to the host
computer.
Ensure compliance with FCC Rules:
- This device complies with Part 15 of the FCC Rules.
- It may not cause harmful interference.
- It must accept any interference received, including
interference that may cause undesired operation. - Any changes or modifications to the unit not approved by the
responsible party could void the user’s authority to operate the
equipment. - This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. - The equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules.
If the equipment causes harmful interference to radio or
television reception, try the following measures to correct the
interference:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and
receiver. - Connect the equipment into an outlet on a different circuit
from that of the receiver. - Consult the dealer or an experienced radio/TV technician for
help.
Note: The user manual also contains information on FCC Rule
Modular and MF Reader SPEC, which can be referred to for more
detailed specifications and regulations.
Brillian RFID System
Multi-Function Reader MF Reader
Manufacturer and publisher Brillian Network & Automation Integrated System Co.,Ltd Add: No.41, Keyi St., Zhunan Township, Miaoli County 350, Taiwan, R.O.C. Tel: 886-37-580708 Fax: 886-37-580728 [email protected] Websitehttp://www.brillian.com.tw
The reproduction of any part of this user manual, in any from (by photocopying, microfilming or any other process) or the processing and distribution of the contents by electronic means is prohibited without the expressed written consent of Brillian. It is prohibited to copy the software or use it for other purposes. it is expressly prohibited to distribute copies of the software to third parties. Violators will be held liable for damage.
Brillian Network & Automation Integrated System Co., Ltd.
Contents
1 Introduction…………………………………………………………………………………………………………….. – 1 2 FCC Rule……………………………………………………………………………………………………………….. – 1 3 MF Reader SPEC …………………………………………………………………………………………………….. – 3 4 MF Reader Module……………………………………………………………………………………………………- 4 –
I
Brillian Network & Automation Integrated System Co., Ltd.
1 Introduction
The Brillian CIDRW(Carrier ID Reader/Writer)is BRILLIAN’s RFID(Radio Frequency Identification) system. The way of basic setup: Put a Transponder(Tag) fixed on the goods which you need to get goods information. The Transponder has a data record for the goods’. During the Host computer sent a order message to the CIDRW through RS232The CIDRW will sent back the goods information which read from the Transponder by radio frequency.
2 FCC Rule Un-license band: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.
This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the
receiver is needed. Consult the dealer or an experienced radio/TV technician for help
– 1 Brillian Network & Automation Integrated System Co., Ltd.
3 FCC Rule Modular
This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users. For laptop installations, the antenna must be installed to ensure that the proper spacing is maintained in the event the users places the device in their lap during use (i.e. positioning of antennas must be placed in the upper portion of the LCD panel only to ensure 20 cm will be maintained if the user places the device in their lap for use) and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as the 2 conditions above are met, further transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.).IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization. End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ASDL modems, certain laptop configurations, and similar equipment). The final end product must be labeled in a visible area with the following: “Contains TX FCC ID: {2A583-MFREADER}”. RF Exposure Manual Information That Must be Included The users manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”Additional Information That Must be Provided to OEM Integrators The end user should NOT be provided any instructions on how to remove or install the device.
– 2 –
Brillian Network & Automation Integrated System Co., Ltd.
4 MF Reader SPEC
Type Working voltage
Idle current Reading/Writing impulse Rod
Antenna current Working frequency Communication spec.(RS232)
Antenna
Dimensions
Certification MARK
MF Reader DC 12~24V
45mA 1A
134.2k Hz 9600,n,8,1 Brillian Antenna L89.7 W88 H22
RemarkAI2400 & MF Reader Use the same way as the application
– 3 –
Brillian Network & Automation Integrated System Co., Ltd.
5 MF Reader Module
5.1 Module Size
– 4 –
Brillian Network & Automation Integrated System Co., Ltd.
5.2 Antenna
– 5 –
Brillian Network & Automation Integrated System Co., Ltd.
Revision History
# Date 1 Feb 27, 2022
Rev. Description 1.0 Standard Version
Name Roxas Li
– 6 –
Brillian Network & Automation Integrated System Co., Ltd.
Brillian Network & Automation Integrated System Co. Ltd.
