RSS210HO-4 Passive Reference 8 Inch Mini Subwoofer Kit
Product Information: Passive Reference 8 Mini Subwoofer
Kit
The Passive Dayton Audio Reference 8 mini subwoofer kit is a
precision cut speaker kit that includes enclosure components and a
driver. The enclosure was cut using CNC machinery for a tight fit
and easy finishing. The kit includes suggested tools and
consumables for assembly and requires a little time and patience to
finish. The package contents include an 8-inch Dayton Audio
RSS210HO-4 Reference Series HO Subwoofer with 4 Ohm impedance and
the following enclosure components:
- Baffle
- 2 x Side Panel
- Back Panel
- 2 x Top/Bottom Panel
- Brace
Product Usage Instructions
- Empty the contents of the package and review parts to ensure
everything has been included and is in good condition. Contact
customer service at 1-800-338-0531 if any parts are missing or
damaged. - Before gluing anything, do a dry fit of the enclosure to
familiarize yourself with the parts and assembly. Ensure that all
pieces have been cut properly. - Set the enclosure parts out on a flat level surface and ensure
that all pieces are free of dust and debris. - Start with the Back Panel (B) lying flat with the rabbeted side
up. Apply a small bead of glue to the inside of all joining
surfaces of the Back Panel (B) and one Top/Bottom panel (E). Then
set in place applying enough pressure to ensure glue is spread
through each joint (some glue squeeze-out can be expected). - Apply a small bead of glue to the inside of all joining
surfaces of one Side Panel (F) and the back and top/bottom panel
assembly. Then set in place applying enough pressure to ensure glue
is spread through each joint (some glue squeeze-out can be
expected). - Apply a small bead of glue to the inside of all joining
surfaces of the Brace (E) and the back, top/bottom, and side panel
assembly. Then slide in place applying enough pressure to ensure
glue is spread through each joint (some glue squeeze-out can be
expected). - Apply a small bead of glue to the inside of all joining
surfaces of the other Side Panel (F) and the enclosure assembly.
Then set in place applying enough pressure to ensure glue is spread
through each joint (some glue squeeze-out can be expected). - Apply a small bead of glue to the inside of all joining
surfaces of the other Top/Bottom Panel (E) and the enclosure
assembly. Then set in place applying enough pressure to ensure glue
is spread through each joint (some glue squeeze-out can be
expected). - Apply a small bead of glue to the inside of all joining
surfaces of the Baffle (E) and the enclosure assembly. Then set in
place applying enough pressure to ensure glue is spread through
each joint (some glue squeeze-out can be expected). - Make sure that all edges are flush and securely apply clamps
from side to side, top to bottom, and front to back. Apply ample
pressure to ensure glue is spread evenly through each joint (some
glue squeeze-out can be expected). Visually inspect all seams to
make sure they are all closed tightly, you may need to relocate
clamps (or add more clamps) to get a perfect fit. In most cases
only 6 clamps will be needed for an enclosure this size.
After assembly, your finished product will provide years of
enjoyment. If you have any questions or concerns about product
usage, please contact our customer service department for
assistance.
Passive Reference 8″ Mini Subwoofer Kit
Thank you for purchasing the Passive Dayton Audio Reference 8″ mini subwoofer kit. The enclosure for this speaker kit was precision cut using CNC machinery for a tight fit to make it easy to finish. With a little time and patience, your finished product will provide years of enjoyment. Please follow these instructions for the best possible results.
Suggested tools and consumables:
Drill Screwdriver Wood clamps (you can never have too many of these) Sanding block and/or electric finishing sander Wood glue
Rag or paper towels Solder Wire stripper/crimper #8 Wood Screws Polyurethane glue (Gorilla Glue)
Package contents:
First, empty the contents of the package and review parts to ensure everything has been included and is in good condition. If any parts are missing or damaged, please contact our customer service department at 1-800-338-0531.
Driver:
A) Dayton Audio RSS210HO-4 8″ Reference Series HO Subwoofer 4 Ohm
Enclosure Components:
B) Baffle C) 2 x Side Panel D) Back Panel E) 2 x Top/Bottom Panel F) Brace
Enclosure Assembly:
1) First, before gluing anything, do a dry fit of the enclosure to familiarize yourself with the parts and assembly. This will also give you a chance to ensure that all pieces have been cut properly. 2) Next, set the enclosure parts out on a flat level surface and ensure that all pieces are free of dust and debris. 3) Start with the Back Panel (B) lying flat with the rabbeted side up, as shown.
4) Apply a small bead of glue to the inside of all joining surfaces of the Back Panel (B) and one Top/Bottom panel (E). Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).
5) Apply a small bead of glue to the inside of all joining surfaces of one Side Panel (F) and the back and top/bottom panel assembly. Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).
6) Apply a small bead of glue to the inside of all joining surfaces of the Brace (E) and the back, top/bottom, and side panel assembly. Then slide in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).
7) Apply a small bead of glue to the inside of all joining surfaces of the other Side Panel (F) and the enclosure assembly. Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).
8) Apply a small bead of glue to the inside of all joining surfaces of the other Top/Bottom Panel (E) and the enclosure assembly. Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).
9) Apply a small bead of glue to the inside of all joining surfaces of the Baffle (E) and the enclosure assembly. Then set in place applying enough pressure to ensure glue is spread through each joint (some glue squeeze-out can be expected).
10) Make sure that all edges are flush and securely apply clamps from side to side, top to bottom, and front to back. Apply ample pressure to ensure glue is spread evenly through each joint (some glue squeeze-out can be expected). Visually inspect all seams to make sure they are all closed tightly, you may need to relocate clamps (or add more clamps) to get a perfect fit. In most cases only 6 clamps will be needed for an enclosure this size.
11) Wipe away any glue squeeze-out on the outside of the enclosure with a damp rag or paper towel (excess glue on the inside is fine). Allow to dry according to the glue manufacturer’s recommendations and remove clamps.
12) Finally, fill any open seams with wood filler or a mixture of sawdust and wood glue. Then sand all surfaces and seams until smooth. Finish enclosure to your liking. See our web page for ideas and examples.
Final Assembly:
13) Locate and install your preferred power terminals (Spring terminals, binding posts, speakON connector, etc…) and internal wiring. 14) Connect the speaker wires to the appropriate terminals on the Dayton Audio RSS210HO-4 8″ Reference Series HO Subwoofer (A). 15) Carefully set the driver into the cutout and secure using the fastener of your choice.
You are now ready to enjoy your finished Passive Reference 8″ Mini Subwoofer!
