HW-HGY-66423 2-Seat Black Metal Outdoor Bench
Product Information
The product is a bench made of wood that can be assembled using
bolts, washers, nuts, and tools provided. The bench consists of two
arms, a back, and a seat with a plate in the middle that can be
pulled up to use as a small table. The maximum load-bearing
capacity of the bench is 250 lbs.
Product Usage Instructions
- Before You Start: Read the instructions
carefully before starting. Ensure that all parts are included and
work in a spacious area close to where the bench will be used. Keep
the hand tools close at hand and do not use power tools to assemble
the furniture. - Board Identification: Identify the parts
labeled on the raw edges of the board. - Hardware List: Check all hardware provided to
ensure everything is included. - Step 1: Attach the seat slat C to the arm B by
bolts D with washers F and nuts G through the pre-drilled holes on
the arm and seat. Repeat for the other side arm B. Do not tighten
completely until assembly is completed. - Step 2: Attach the back A to arm B by
inserting bolts E with washers F and nuts G through the pre-drilled
holes on the arm and back. Repeat for other side arm B. - Step 3: Tighten all bolts with the wrench and
allen wrench provided. Turn the bench to the upright position. The
plate in the middle of the seat can be pulled up and fixed as a
small table. - Maximum Loads: Do not exceed the maximum
load-bearing capacity of 250 lbs to avoid instability and possible
injuries. - Care and Maintenance: Keep the furniture in a
climate-controlled environment away from direct sunlight to avoid
fading, warping, shrinking, and splitting of wood. Proper care and
cleaning will extend the life of the bench.
Before You Start
Read each step carefully before starting. It is very important to ensure each step followed in correct order, otherwise assembly difficulties may occur. Most of board parts are labeled or stamped on the raw edges. Have a check to make sure all parts are included. Work in a spacious area, preferably on a carpet close to where the unit will be used. Keep the handtools close at hand. Do not use power tools to assemble your furniture. They may scratch or damage the parts.
01
Board Identification
Not actual size
Arms x 2
Back x 1 Seat x 1 02
Board Identification
Not actual size A
B B
C
03
BOLT D x4
Hardware List
Actual size
E x4
M6 x 50mm
WASHER F x8 M6
NUTS G x8 M6
M6 x 70mm
ALLEN WRENCH F x1 4×4
WRENCH I x1 M6
04
STEP 1
Attach the seat slat C to the arm B by bolts D with washers F .nuts G through the pre-drilled holes on the arm and the pre-drilled holes on the seat . Repeat step for the other side arm B .
IMPORTANT: Do not tighten completely until assembly is completed.
C
G
B
F
B D
B C
05
STEP 2
Attach the back A to the arm B by inserting bolts E with washers F ,nuts G through the pre-drilled holes on the arm and the pre-drilled holes on the back. Repeat step for the other side arm B .
A
G
F
A
E B
06
STEP 1
Tighten all the bolts with the wrench and the allen wrench,and turn the bench to the upright position. The plate in the middle of the seat can be pulled up and fixed as a small table. Your bench is now ready for use, so relax & enjoy!
07
Maximum Loads
250 lbs
250 lbs
This item is only suitable within the specified maximum load-bearing. Heavier loads than the indicated load capacity may cause instability, resulting in possible injuries.
08
Care and Maintenance
Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage the finish. Never use water to clean your furniture as it may cause damage to the finish. Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid rubbing. Check bolts/screws periodically and tighten them if necessary.
Further advice about wood furniture care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish. Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages.
09
