B0BWJ9Y71G Solidcom C1 Pro Wireless Intercom Headset System
Hollyland Solidcom C1 Pro
User Manual
Version: V2.0.0
Introduction
Thank you for purchasing the Hollyland Solidcom C1 Pro
full-duplex wireless noise cancelling intercom system. The Solidcom
C1 Pro is Hollyland’s first wireless self-contained intercom system
with Environmental Noise Cancellation (ENC), utilizing advanced
DECT technology. It operates in the 1.9GHz band, providing a
reliable line-of-sight (LOS) range of up to 1,100ft (350m). This
User Manual will guide you through the installation and use of the
equipment.
Packing List
| Solidcom C1 Pro – 2S 2-person Noise Cancelling Headset Intercom | |
|---|---|
| Master Headset (With Red Nameplate) | x1 |
| Remote Headset (With Blue Nameplate) | x1 |
| Charging Case | x1 |
| Battery | x4 |
| Microphone Cushion | x2 |
| Over-ear Leather Cushion | x2 |
| On-ear Foam Cushion | x2 |
| USB-A to USB-C Cable | x1 |
| Storage Case | x1 |
| User Manual | x1 |
| Warranty Card | x1 |
Note: The quantity of the items depends on the product
configuration.
Operation Guide
- Install the battery.
- Step 1: Slide the battery compartment cover lock.
- Step 2: Open the cover.
- Step 3: Place the battery into the compartment and close the
cover.
- Step 4: Ensure that all the headsets are turned ON.
- Step 5: The indicator light stops flashing and stays on.
Hollyland Solidcom C1 Pro
User Manual
V2.0.0
Introduction
Thank you for purchasing Hollyland Solidcom C1 Pro full-duplex wireless noise cancelling intercom system. The Solidcom C1 Pro, adopting the advanced DECT technology, is Hollyland’s first wireless selfcontained intercom system with Environmental Noise Cancellation (ENC). The system operates in the 1.9GHz band, providing a reliable LOS range of up to 1,100ft (350m). This User Manual will help you through the installation and use of the equipment.
EN-01
Packing List
(With Red Nameplate) (With Blue Nameplate)
Solidcom C1 Pro – 2S 2-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate)
x1
Remote Headset (With Blue Nameplate)
x1
Charging Case
x1
Battery
x4
Microphone Cushion
x2
Over-ear Leather Cushion
x2
On-ear Foam Cushion
x2
USB-A to USB-C Cable
x1
Storage Case
x1
User Manual
x1
Warranty Card
x1
Note: The quantity of the items depends on the product configuration.
EN-02
Packing List
(With Red Nameplate) (With Blue Nameplate)
Solidcom C1 Pro – 3S 3-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate)
x1
Remote Headset (With Blue Nameplate)
x2
Charging Case
x1
Battery
x6
Microphone Cushion
x3
Over-ear Leather Cushion
x3
On-ear Foam Cushion
x3
USB-A to USB-C Cable
x1
Storage Case
x1
User Manual
x1
Warranty Card
x1
Note: The quantity of the items depends on the product configuration.
EN-03
Packing List
(With Red Nameplate) (With Blue Nameplate)
Solidcom C1 Pro – 4S 4-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate)
x1
Remote Headset (With Blue Nameplate)
x3
Charging Case
x1
DC Adapter
x1
Battery
x8
Microphone Cushion
x4
Over-ear Leather Cushion
x4
On-ear Foam Cushion
x4
USB-A to USB-C Cable
x1
Storage Case
x1
User Manual
x1
Warranty Card
x1
Note: The quantity of the items depends on the product configuration.
EN-04
Packing List
(With Red Nameplate) (With Blue Nameplate)
Solidcom C1 Pro – 6S 6-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate)
x1
Remote Headset (With Blue Nameplate)
x5
Charging Case
x1
DC Adapter
x1
Battery
x12
Microphone Cushion
x6
Over-ear Leather Cushion
x6
On-ear Foam Cushion
x6
USB-A to USB-C Cable
x1
Storage Case
x1
User Manual
x1
Warranty Card
x1
Note: The quantity of the items depends on the product configuration.
EN-05
Packing List
(With Red Nameplate) (With Blue Nameplate)
Solidcom C1 Pro – 8S 8-person Noise Cancelling Headset Intercom
Master Headset (With Red Nameplate)
x1
Remote Headset (With Blue Nameplate)
x7
Charging Case
x1
DC Adapter
x1
Battery
x16
Microphone Cushion
x8
Over-ear Leather Cushion
x8
On-ear Foam Cushion
x8
USB-A to USB-C Cable
x1
Storage Case
x1
User Manual
x1
Warranty Card
x1
Note: The quantity of the items depends on the product configuration.
EN-06
Operation Guide
Install the battery.
Step 1: Slide the battery compartment cover lock.
Step 2: Open the cover.
Turn on the master headset and remote headsets.
Step 3: Place the battery into the compartment and close the cover.
Nameplate Power Toggle
Master Headset Startup
Turn on the microphone.
1. Ensure that all the headsets are turned ON. 2. The indicator light stops flashing and stays
ON when the master headset is successfully connected with the remote headsets. 3. Red nameplate: Master headset Blue nameplate: Remote headset
ON No Rotation
Microphone Boom Rotation
ON No Rotation
Rotate the microphone boom upwards clockwise.
Rotate the microphone boom upwards counterclockwise.
The Solidcom C1 Pro system is now ready for use.
EN-07
Pairing The master headset is paired with the remote headsets at the factory. They are ready for use right out of box. Manual pairing is only required when a new headset is added to the system. During the pairing process, all the headsets must be turned ON and connected. Pairing steps: 1. Press and hold the A button on both the master headset and remote headsets for 5 seconds.
Pairing is completed when the indicator light on each microphone boom stops flashing and stays ON. 2. One master headset can be paired with up to 7 remote headsets.
Solidcom C1 Pro is highly versatile and can be applied in a variety of usage scenarios. For more information about how to operate this system, please visit https://hollyland-techhelp.zendesk.com/hc/en-us/categories/360005064994-Download
EN-08
Parameters
Transmission Range
1,100ft (350m) LOS
Frequency Band
1.9 GHz (DECT) (varies by country and region)
Modulation Mode
GFSK
TX Power
21dBm (125.9 mW)
RX Sensitivity
<-90dBm
Battery Capacity
700mAh (2.66Wh)
Operation Time
Remote headset: >10 hours (when ENC is turned ON) Master headset: >5 hours (when ENC is turned ON and the master headset is connected with 5 remote headsets) Master headset: >4 hours (when ENC is turned ON and the master headset is connected with 7 remote headsets)
Charging Time
About 2.5 hours
Frequency Response
ENC OFF: 150Hz7kHz (fluctuation range: ±6dB) ENC ON: 150Hz7kHz (fluctuation range: ±10dB)
Signal-to-Noise Ratio 71±2dB@94dBSPL, 1kHz
Distortion
<1%@94dBSPL, 150Hz7kHz
Microphone Type
Electret
Input SPL
>115dBSPL
Output SPL
94±3dBSPL (@94dBSPL, 1kHz)
20dB±2 with two microphones ENC
(relative to environmental noise in all directions)
Net Weight
About 170g (6oz) with batteries included
Temperature Range
0 to 45 (working condition) 10 to 60 (storage condition)
Note: The frequency band and TX power vary by country and region.
EN-09
Safety Precautions
Do not place the product near or inside heating devices (including but not limited to microwave ovens, induction cookers, electric ovens, electric heaters, pressure cookers, water heaters, and gas stoves) to prevent the battery from overheating and exploding. Do not use non-original charging cases, cables, and batteries with the product. The use of non-original spare parts may cause electric shock, fire, explosion, or other dangers.
EN-10
Support
If you encounter any problems in using the product or need any help, please contact Hollyland Support Team via the following ways:
Hollyland User Group HollylandTech HollylandTech HollylandTech [email protected] www.hollyland-tech.com
EN-11
Statement All copyrights belong to Shenzhen Hollyland Technology Co., Ltd. Trademark Statement Without the written approval of Shenzhen Hollyland Technology Co., Ltd., no organization or individual may copy or reproduce part or all of any written or illustrative content and disseminate it in any form. Note: Due to product version upgrades or other reasons, this User Manual will be updated from time to time. Unless otherwise agreed, this document is provided as a guide for use only. All representations, information, and recommendations in this document do not constitute warranties of any kind, express, or implied.
EN-12
FCC Requirement
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device. This device complies with Part 15 of the FCC Rules. Operations are subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including interference that may cause
undesired operations.
FCC Radiation Exposure Statement: The device has been tested and complies with FCC SAR limits.
Note: This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if it is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause harmful intefrference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the distance between the device and the receiver. Connect the device to an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
EN-13
Hollyland - Wireless Video Transmitter, Intercom, Microphone
