Milwaukee M12 Fhir14 Cordless Ratchet Wrench Instruction Manual (+ PDF)

Contents hide

M12 FHIR14 Cordless Ratchet Wrench

Product Information

The product is a cordless industrial screwdriver with two models
available: M12 FHIR14 and M12 FHIR38. The production codes for the
models are 4830 62 01 and 4830 69 01, respectively. The tool
reception for M12 FHIR14 is 1/4 (6.35 mm) and for M12 FHIR38 is 3/8
(9.5 mm).

Product Usage Instructions

Before starting any work on the machine, remove the battery
pack.
For all work on the machine, remove the battery pack.
Check the plug and power cord for any damage. Only a
professional should repair any damages.
When working with the machine, press and hold the button for
2-3 seconds to start.
The LED light indicates the battery level: 100%, 75%, 50%, and
25%.
To change the tool, click the button to stop the machine, and
remove the current tool. Insert the new tool and click the button
to start again.

Note: Always refer to the product manual for safety instructions
and technical data.

View Fullscreen

M12 FHIR14 M12 FHIR38

Original instructions Originalbetriebsanleitung Notice originale Istruzioni originali Manual original Oorspronkelijke gebruiksaanwijzing Original brugsanvisning Original bruksanvisning Bruksanvisning i original Alkuperäiset ohjeet

Orijinal iletme talimati Pvodním návodem k pouzívání Pôvodný návod na pouzitie Instrukcj oryginaln Eredeti használati utasítás Izvirna navodila Originalne pogonske upute Instrukcijm oriinlvalod Originali instrukcija

Algupärane kasutusjuhend
Instruciuni de folosire originale

ENGLISH DEUTSCH FRANÇAIS ITALIANO ESPAÑOL PORTUGUES NEDERLANDS DANSK NORSK SVENSKA SUOMI TÜRKÇE CESKY SLOVENSKY POLSKI MAGYAR SLOVENSKO HRVATSKI LATVISKI LIETUVISKAI EESTI ROMÂNIA
2

12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3 12 3

Picture section with operating description and functional description Bildteil mit Anwendungs- und Funktionsbeschreibungen Partie imagée avec description des applications et des fonctions Sezione illustrata con descrizione dell’applicazione e delle funzioni Sección de ilustraciones con descripción de aplicación y descripción funcional Parte com imagens explicativas contendo descrição operacional e funcional Beeldgedeelte met toepassings- en functiebeschrijvingen Billeddel med anvendelses- og funktionsbeskrivelser Bildedel med bruks- og funksjonsbeskrivelse Bilddel med användnings- och funktionsbeskrivning Kuvasivut käyttö- ja toimintakuvaukset Resim bölümü Uygulama ve fonksiyon açiklamalari ile birlikte Obrazová cást s popisem aplikací a funkcí Obrazová cass popisom aplikácií a funkcií
Cz rysunkowa z opisami zastosowania i dzialania
Képes részalkalmazási- és mködési leírásokkal
Del slikez opisom uporabe in funkcij
Dio sa slikamasa opisima primjene i funkcija
Attla daa ar lietosanas un funkciju aprakstiem
Paveiksllio dalissu vartojimo instrukcija ir funkcij aprasymais
Pildiosa kasutusjuhendi ja funktsioonide kirjeldusega

Secvena de imagine cu descrierea utilizrii i a funcionrii

Text section with Technical Data, important Safety and Working Hints and description of Symbols

Textteil mit Technischen Daten, wichtigen Sicherheits- und Arbeitshinweisen und Erklärung der Symbole.

Partie textuelle avec les données techniques, les consignes importantes de sécurité et de travail ainsi que l’explication des pictogrammes.

Sezione testo con dati tecnici, importanti informazioni sulla sicurezza e sull`utilizzo, spiegazione dei simboli.

22 Sección de texto con datos técnicos, indicaciones importantes de seguridad y trabajo y explicación de los símbolos.

Parte com texto explicativo contendo Especificações técnicas, Avisos de segurança e de operação e a Descrição dos símbolos.

Tekstgedeelte met technische gegevens, belangrijke veiligheids- en arbeidsinstructies en verklaring van de symbolen.

Tekstdel med tekniske data, vigtige sikkerheds- og arbejdsanvisninger og symbolforklaring.

Tekstdel med tekniske data, viktige sikkerhets- og arbeidsinstruksjoner og forklaring av symbolene.

Textdel med tekniska informationer, viktiga säkerhets- och användningsinstruktioner samt symbolförklaringar.

Tekstisivut: tekniset tiedot, tärkeät turvallisuus- ja työskentelyohjeet sekä merkkien selitykset.

, .

Teknik bilgileri, önemli güvenlik ve çalima açiklamalarini ve de sembollerin açiklamalarini içeren metin bölümü.

Textová cást s technickými daty, dlezitými bezpecnostními a pracovními pokyny a s vysvtlivkami symbol

Textová cas s technickými dátami, dôlezitými bezpecnostnými a pracovnými pokynmi a s vysvetlivkami symbolov

Cz opisowa z danymi technicznymi, wanymi wskazówkami dotyczcymi bezpieczestwa i pracy oraz objanieniami symboli.

Szöveges rész mszaki adatokkal, fontos biztonsági- és munkavégzési útmutatásokkal, valamint a szimbólumok magyarázata.

Del besedila s tehnicnimi podatki, pomembnimi varnostnimi opozorili in delovnimi navodili in pojasnili simbolov.

Dio stiva sa tehnickim podacima, vaznim sigurnosnim i radnim uputama i objasnjenjem simbola.

Teksta daa ar tehniskajiem parametriem, svargiem drosbas un darbbas nordjumiem, simbolu atsifrjumiem.

Teksto dalis su techniniais duomenimis, svarbiomis saugumo ir darbo instrukcijomis bei simboli paaiskinimais.

Tekstiosa tehniliste näitajate, oluliste ohutus- ja tööjuhenditega ning sümbolite kirjeldustega.

, , , .

, .

Poriune de text cu date tehnice, indicaii importante privind sigurana i modul de lucru i descrierea simbolurilor.

, .

START

STOP

Remove the battery pack before starting any work on the machine.

Vor allen Arbeiten an der Maschine den Wechselakku herausnehmen

Avant tous travaux sur la machine retirer l’accu interchangeable.

Prima di iniziare togliere la batteria dalla macchina.

Retire la batería antes de comenzar cualquier

trabajo en la máquina.

Antes de efectuar qualquer intervenção na máquina retirar o bloco acumulador.

Voor alle werkzaamheden aan de machine de akku verwijderen.

Ved arbejde inden i maskinen, bør batteriet tages ud.

Ta ut vekselbatteriet før du arbeider på maskinen

Drag ur batteripaket innan arbete utföres på maskinen.

Tarkista pistotulppa ja verkkojohto mahdollisilta vauriolta. Viat saa korjata vain alan erikoismies.

Ðñéí áðü êÜèå åñãáóßá óôç ìç÷áíÞ áöáéñåßôå ôçí áíôáëëáêôéêÞ ìðáôáñßá.

Aletin kendinde bir çalima yapmadan önce kartu aküyü çikarin.

Ped zahájením veskerých prací na vrtacím sroubováku vyjmout výmnný akumulátor.

Pred kazdou prácou na stroji výmenný akumulátor vytiahnu.

Przed przystpieniem do jakichkolwiek prac na elektronarzdziu naley wyj wkladk akumulatorow.

Karbantartás, javítás, tisztítás, stb. eltt az akkumulátort ki kell venni a készülékbl.

Pred deli na stroju izvlecite izmenljivi akumulator.

Prije svih radova na stroju izvaditi bateriju za zamjenu.

Pirms masnai veikt jebkda veida apkopes darbus, ir jizem r akumultors.

Pries atlikdami bet kokius darbus renginyje,

isimkite keiciam akumuliatori.

Enne kõiki töid masina kallal võtke vahetatav aku välja.

Bûíüòå àêêóìóëÿòîð èç ìàøèíû ïåðåä ïðîâåäåíèåì ñ íåé êàêèõ-ëèáî ìàíèïóëÿöèé.

Scoatei acumulatorul înainte de a începe orice intervenie pe main.

– .

click

2 2-3 sec 1

100%

75%

50%

25%

click

START

Handle (insulated gripping surface) Handgriff (isolierte Grifffläche) Poignée (surface de prise isolée) Impugnatura (superficie di presa isolata) Empuñadura (superficie de agarre con aislamiento) Manípulo (superfície de pega isolada) Handgreep (geïsoleerd) Håndtag (isolerede gribeflader) Håndtak (isolert gripeflate) Handtag (isolerad greppyta) Kahva (eristetty tarttumapinta) ( ) El kulpu (izolasyonlu tutma yüzeyi) Rukoje (izolovaná uchopovací plocha) Rukovä (izolovaná úchopná plocha) Uchwyt (z izolowan powierzchni) Fogantyú (szigetelt fogófelület) Rocaj (izolirana prijemalna povrsina) Rukohvat (izolirana povrsina za drzanje) Rokturis (izolta satversanas virsma) Rankena (izoliuotas rankenos pavirsius) Käepide (isoleeritud pideme piirkond) ( ) ( ) Mâner (suprafa de prindere izolat) ( ) ( )
( )

STOP

TECHNICAL DATA CORDLESS INDUSTRIAL SCREWDRIVER

M12 FHIR14

M12 FHIR38

Production code………………………………………………………………………. …………………….4830 62 01… ……………..4830 69 01…

…000001-999999

Tool reception …………………………………………………………………………. ………………………. 1/4″ (6,35 mm)……………… 3/8″ (9,5 mm)

No-load speed ………………………………………………………………………… ……………………. 0-450 min-1 ………………….. 0-450 min-1

Torque max…………………………………………………………………………….. ……………………… 47,5 Nm ……………………… 47,5 Nm

Battery voltage………………………………………………………………………… ………………………… 12 V……………………………. 12 V

Weight according EPTA-Procedure 01/2014 (Li-Ion 2,0 Ah … 6,0 Ah) ….. …………….. 0,96…1,20 kg ………………. 0,96…1,20 kg

Recommended ambient operating temperature…………………………… …………………………………… -18°C … +50°C

Recommended battery types…………………………………………………….. ………………………………………… M12B…

Recommended charger……………………………………………………………. ……………………………. C12C, M12C4, M12-18…

Noise/vibration information Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:
Sound pressure level (Uncertainty K=3dB(A)) ………………………….. ……………………. 84,26 dB (A)………………… 84,26 dB (A) Sound power level (Uncertainty K=3dB(A)) ……………………………… ……………………. 95,26 dB (A)………………… 95,26 dB (A) Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 62841. Vibration emission value ah :
Impact tightening of fasteners of the maximum capacity of the tool ……………………… 2,88 m/s2 …………………….. 2,88 m/s2 Uncertainty K =…………………………………………………………………….. ……………………… 1,50 m/s2 …………………….. 1,50 m/s2
WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration and noise emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

WARNING Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
IMPACT DRIVER SAFETY WARNINGS
Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a ,,live” wire may make exposed metal parts of the power tool ,,live” and could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.
ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.
The possible causes may be: · it is tilted in the workpiece to be machined · it has pierced through the material to be machined · the power tool is overloaded
Do not reach into the machine while it is running.
The insertion tool may become hot during use. · when changing tools · when setting the device down
Chips and splinters must not be removed while the machine is running.

When working in walls ceiling, or floor, take care to avoid electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors offer to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk).
Use only System M12 chargers for charging System M12 battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.
Warning! To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.
SPECIFIED CONDITIONS OF USE
The cordless industrial screwdriver can be used to tighten and loosen nuts and bolts wherever no mains connection is available.
Do not use this product in any other way as stated for normal use.
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that the product described under “Technical Data” fulfills all the relevant regulations and the directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized standards have been used:

14 ENGLISH

EN 62841-1:2015 EN 62841-2-2:2014 EN 55014-1:2017+A11:2020 EN 55014-2:2015 EN IEC 63000:2018 Winnenden, 2020-10-27
Alexander Krug Managing Director Authorized to compile the technical file. Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfills all the relevant provisions of the following Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and that the following designated standards have been used: BS EN 62841-1:2015 BS EN 62841-2-2:2014 BS EN 55014-1:2017+A11:2020 BS EN 55014-2:2015 BS EN IEC 63000:2018 Winnenden, 2020-10-27
Alexander Krug Managing Director Authorized to compile the technical file. Techtronic Industries GmbH Max-Eyth-Straße 10 71364 Winnenden Germany
BATTERIES
Battery packs which have not been used for some time should be recharged before use. Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating). The contacts of chargers and battery packs must be kept clean. For an optimum life-time, the battery packs have to be fully charged, after used. To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged. For battery pack storage longer than 30 days: Store the battery pack where the temperature is below 27°C and away from moisture Store the battery packs in a 30% – 50% charged condition Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION
In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 5 seconds, the fuel gauge will flash,and then the tool will turn OFF. To reset, release the trigger. Under extreme circumstances, the internal temperature of the battery pack could raise too much. If this happens, the fuel gauge will flash until the battery pack cooled down. After the lights go off, the work may continue.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.

Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations. · The user can transport the batteries by road without further
requirements. · Commercial transport of Lithium-Ion batteries by third parties is
subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts. When transporting batteries: · Ensure that battery contact terminals are protected and insulated to prevent short circuit. · Ensure that battery pack is secured against movement within packaging. · Do not transport batteries that are cracked or leak. Check with forwarding company for further advice
MAINTENANCE Use only Milwaukee accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses). If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the machine.
Please read the instructions carefully before starting the machine.
Do not dispose electric tools, batteries/rechargeable batteries together with household waste material. Electric tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Check with your local authority or retailer for recycling advice and collection point.
n0 No-load speed V Volts
Direct current
European Conformity Mark)
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark

ENGLISH 15

Copyright 2020
Techtronic Industries GmbH Max-Eyth-Str. 10 71364 Winnenden Germany
+49 (0) 7195-12-0
www.milwaukeetool.eu

Techtronic Industries (UK) Ltd Fieldhouse Lane Marlow Bucks SL7 1HZ UK

(11.20)
4931 4704 79