MS-8M-360-MW Microwave Sensor
Product Information: Sensor
The Sensor is an electronic device that detects motion and
presence within its detection range. It is designed to be used in
indoor and outdoor settings and can be used for security, lighting,
and energy-saving purposes. The Sensor has the following
specifications:
- Voltage: 220-240V/AC
- Power Frequency: 50/60Hz
- Detection Distance: 16m, adjustable
- Ambient Light:
Product Usage Instructions:
Before using the Sensor, please ensure that the power supply is
connected and turned on. Follow the below steps to use the
Sensor:
- Locate the Sensor in a suitable position where it can detect
motion within its detection range. - Adjust the detection distance as per your requirement. The
detection distance can be adjusted using the adjustment knob
provided on the Sensor. - The Sensor is equipped with an ambient light sensor that allows
it to work efficiently in different lighting conditions. Ensure
that the ambient light is appropriate for the Sensor to work
correctly. - The Sensor will detect motion within its detection range and
activate any connected devices or systems accordingly. - If you face any issues while using the Sensor, please refer to
the user manual or contact the manufacturer for assistance.
By following these instructions, you can effectively use the
Sensor for your desired purpose.
SENSOR
1800 909 306
nedlandsgroup.com.au [email protected]
Welcome to using the POWER-LITE Microwave Sensor! A new saving-energy product; the microwave sensor uses high-frequency electro-magnetic wave (5.8GHz) and integrated circuit. It gathers automatism, convenience, safety, saving-energy and practical functions. The wide detection field depends on detectors. It works by receiving human motion. When one enters the detection field, it can start the load at once and automatically identifies day and night. Installation is very convenient. Detection is possible through doors, panes of glass or thin walls.
SPECIFICATIONS:
Voltage: 220-240V/AC
Detection Range: 360°
Power Frequency: 50/60Hz
Detection Distance: 16m, adjustable
Ambient Light: <3-2000LUX (Adjustable)
HF System: 5.8GHz CW radar, ISM band
Time Delay: Min. 10sec±3sec
Transmission Power: <0.2mW
Max. 12min±1min
Installing Height: 1.5-3.5m
Rated Load: 1200W max (Incandescent)
Power Consumption: approx 0.9W
600W max (Fluorescent & LED) Detection Motion Speed: 0.6-1.5m/s
FUNCTION:
· Can identify
day and night when it is adjusted on the “sun” position
(max). When adjusted on the “3” position (min), it will work under less than 3LUX. As for
the adjustment pattern, please refer to the testing method.
· SENS (sensitivity) adjustable: It can be adjusted according to the location. The detection
distance at low sensitivity can be set to just 2m and high sensitivity of up to 16m, making it
suitable for large spaces. Height-dependent.
· Time-Delay is added continually: When it receives the second induction signal within
the first induction, it will restart to time from the moment.
· TimeDelay is adjustable. It can be set according to the user’s needs. The minimum time is
10sec±3sec. The maximum is 12min±1min.
NOTE: The high-frequency output of the HF sensor is <0.2Mw- that is just one 5000th of the transmission power of a mobile phone or the output of a microwave oven.
INSTALLATION: (see the diagram) · Switch off the power and remove the transparent cover. · Connect the power to connection terminal of sensor according to connection-wire diagram. · Install the transparent cover back into the original location. · Fold the metal spring of the sensor upwards and then put the sensor into the suitable hole
or installation box. Releasing the spring, the sensor will be set in this installation position. · After finishing installing, turn on the power and then test it.
· When you switch on the power, the light will be on at once. And 10sec±3sec later the light will automatically turn off. Then if the sensor receives induction signal again, it can work normally.
· When the sensor receives the second induction signals within the first induction, it will restart to time from the moment.
· Turn LUX knob anti-clockwise on the minimum (3). If the ambient light is less than 3LUX (darkness), the inductor load could work when it receives induction signal.
Note: When testing in daylight, please turn LUX knob to the sensor may not work!
(SUN) position, otherwise
CONNECTION-WIRE DIAGRAM:
TEST: · Turn the LUX knob clockwise on the maximum
(sun). Turn the SENS knob clockwise on the maximum (+). Turn the TIME knob anti-clockwise on the minimum (10s).
16m Detection Distance
NOTES: · Installation must be undertaken by a licensed Electrician. · Cannot be installed on uneven and shaky surface. · In front of the sensor, ensure that there is no obstructive object/s affecting the detection. · Avoid installing it near metal and glass which may affect the sensor. · For your safety, please do not open the cover if you find a problem after installation.
TROUBLESHOOTING: · The load does not work:
a. Check the power and the load. b. Does the indicator light turn on after sensing? If yes, please check load. c. If the indicator light is not on after sensing, please check if the working light corresponds to the ambient light. d. Please check if the working voltage corresponds to the power source. · The sensitivity is poor: a. Please check the ambient temperature. b. Please check if the signals source is in the detection fields. c. Please check the installation height (1.5-3.5m) · The sensor will not automatically turn off the load: a. Check if there are continual signals in the detection fields. b. Check if the time delay is set to the longest. c. Check if the power corresponds to the instruction.
LED Lighting Manufacturer - Perth and Melbourne - Nedlands Group
