High Flow Intake Ducts
Product Information
The High Flow Intake system is designed for the following
Porsche Macan models:
- Porsche Macan S (3.0L) 340HP (2015-2018)
- Porsche Macan GTS (3.0L) 360HP (2017-2019)
- Porsche Macan Turbo (3.6L) 400HP (2015-2019)
The system includes:
- 2X High Flow Intake Ducts
- 2X High Flow Air Filters
If you need technical assistance or help with the installation
procedure, please email [email protected]
for immediate help.
Product Usage Instructions
- Open the hood to your Macan and locate the factory
airboxes. - Lift up the rubber gasket seals on top of the airbox and place
them to the side. Note: The rubber gasket will be used with the
High Flow Ducts. - Remove the (4) T-25 bolts from the top of the airbox. Lift the
OEM tops off the factory airbox and fully remove the screws from
the tops. Put them in a safe place as they will be reused on the
High Flow Ducts. - Lift up and slide the side panel of the factory airbox and
place it to the side. If your Macan has a coolant reservoir bleeder
valve attached to the air box side panel, simply pull up on the
valve to remove it. - Remove the factory air filter from the airbox by pulling near
the airbox outlet. - Place the High Flow Air Filter inside the airbox with the
appropriate orientation to the airbox outlet. Press firmly on both
the top and bottom to ensure the High Flow Air Filter slides into
the airbox outlet. There is a small ridge on the air filter that
goes over a plastic tab on the top side of the airbox. The filter
might feel loose, but the sliding side panel will secure the final
fit of the filter. - Ensure the filter is oriented correctly. Insert the side panel
back into the airbox via the track located near the edge of the
airbox. Slide the panel into place and ensure a snug fit. - Place the High Flow Ducts on top of the factory airbox and
insert the (4) screws into the holes of each airbox side. P is for
the passenger side airbox, while D is for the driver’s side airbox.
Tighten the bolts down. - Install the rubber gaskets on top of the High Flow Ducts and
ensure they are properly set in the grooves. Press firmly on top of
the rubber to ensure they are properly seated into the
grooves. - Close your hood and take your Macan for a spin. Enjoy the
improved turbo response and power output!
To maximize the power output of this system, it is recommended
to tune your Macan to take advantage of the increased airflow.
Calibrations are available for Macan S, GTS, and Turbo for Cobb
Accessport users. Please contact us with any questions.
If you enjoy the product, please share your experience,
pictures, and videos on the MacanForum and social media! Tag us
with @flat6motorsports or #flat6motorsports for a chance to win a
gift card or a free product giveaway.
INSTALLATION GUIDE
HIGH FLOW INTAKE system
PORSCHE MACAN S / GTS / TURBO (95B.1)
FITMENT
2015 – 2018 Porsche Macan S (3.0L) 340HP 2017 – 2019 Porsche Macan GTS (3.0L) 360HP 2015 – 2019 Porsche Macan Turbo (3.6L) 400HP
TECHNICAL HELP
If you need technical assistance or help with the installation procedure, please email [email protected] for immediate help.
IN THE BOX
2X High Flow Intake Ducts 2X High Flow Air Filters
P
D
TOOLS NEEDED
T-25 Torx Bit / Driver Socket Wrench (if applicable)
watch inst
Scan to
all video
1 ) Open the hood to your Macan and locate the factory airboxes.
2 ) Lift up the rubber gasket seals on top of the airbox and place them to the side.
NOTE
The rubber gasket will be used with the High Flow
Ducts.
3)
Remove the (4) T-25 bolts from the top of the airbox. You can lift the OEM tops off the factory
airbox and then fully remove the screws from the tops, put in a safe place. The screws will be
reused on the High Flow Ducts.
REFERENCE PICTURE
P
D
4 ) Lift up and slide the side panel of the factory airbox and place to the side.
The driver’s side airbox has a coolant reservoir bleeder valve attached to the air box side panel. This can be removed by simply pulling up on the valve.
REFERENCE PICTURE
5 ) Next, remove the factory air filter out of the airbox by pulling near the airbox outlet (bottom on the
Macan S / GTS / Turbo and top on the 2.0T and Diesel)
Removal of the factory air filter is now complete, now it’s time to install the Flat 6 Motorsports High Flow Air Filters.
[email protected]
6 ) Place the High Flow Air Filter inside the airbox with the appropriate orientation to the airbox outlet.
Press firmly on both the top and bottom to insure the High Flow Air Filter slides into the airbox outlet.
There is a small ridge on the air filter that goes over a plastic tab on the top side of the airbox. The filter might feel loose but the sliding side panel will secure the final fit of the filter.
7 ) Ensure the filter is oriented correctly. Insert the side panel back into the airbox via the track
located near the edge of the airbox. Slide the panel into place and ensure a snug fit.
8 ) Place the High Flow Ducts on top of the factory airbox and insert the (4) screws into the holes of
each airbox side. Refer to previous images and note P is for the passenger side airbox while D is for the driver’s side airbox. Tighten the bolts down.
[email protected]
9 ) Next, install the rubber gaskets on top of the High Flow Ducts and ensure they are properly set in
the groves. Press firmly on top of the rubber to ensure they are properly seated into the groves.
Installation of the High Flow Intake System is now complete! Close your hood and take your Macan for a spin.
Enjoy the improved turbo response and power output! To maximize the power output of this system, we recommend
tuning your Macan to take advantage of the increased airflow. We have calibrations available for the Macan S, GTS, and Turbo for Cobb Accessport users. Please contact us
with any questions.
ENJOY THE PRODUCT?
Enjoy the product? Please share your experience, pictures and videos on the MacanForum and social media! Tag us with @flat6motorsports or #flat6motorsports for a chance to win a gift card or a free product giveaway.
MAINTENANCE OF FILTERS
The Flat 6 Motorsports High Flow Air Filters are designed to be lifetime filters but for optimal performance it is recommended to clean every 15,000 miles. To service the filters, fill a bucket
with dish soap (Dove, Palmolive, etc.) and tap water. Place the filter into the bucket with the cleaning solution. Let soak for 8-10 minutes. Rinse the air filter out with water from the inside of the filter pushing out any dirt. Do not use a pressure cleaner on the filter. Once rinsed thoroughly shake
the filter to get as much water out of it then let it dry. Do not use a hair dryer, compressed air or any other kind of heat source to dry the filter. It may take a full day for the filter to properly dry.
[email protected]
