Electrical Safety: Ensure that all
installation and operation adhere to local electrical safety codes.
Use a certified/listed 12VDC Class 2 power supply or adequate PoE
switch. The product must be grounded to reduce the risk of electric
shock. Improper handling and installation may result in fire or
electrical shock.
Operation and Daily Maintenance: Prior to any
maintenance work, shut down the device and unplug the power cable.
Avoid touching the CMOS sensor optic component. Clean the lens
surface with a blower or dry soft cloth. For excessive dust, use a
cloth.

Warning

This camera should be installed and examined by qualified
personnel only. Unauthorized changes or modifications may void the
warranty.

Statement

This guide is for reference only. Product, manuals, and
specifications may be modified without prior notice. Speco
Technologies reserves the right to modify these without notice and
without incurring any obligation. Speco Technologies is not liable
for any loss caused by improper operation.

Note

Before installation, check the package and ensure that all
components are included. Contact your representative or Speco
customer service department immediately if any item is broken or
missing.

Product Usage Instructions

Package Contents:

Component	Quantity
Camera	1
Quick start guide	1
CD	1
Screwdriver	1
Plastic screw anchors	3
Drill Template	1

Camera Overview:

Connecting Network Cable:

Loosen the nut from the main element.
Run the network cable (without RJ 45 connector) through both
elements.
Crimp the cable with an RJ 45 connector.
Connect the cable to the water-proof connector.
Tighten the nut and the main cover.

Installation:

Note: Before you start, ensure that the wall or
ceiling is strong enough to withstand three times the weight of the
camera and the junction box.

Attach the drill template to the desired installation
location.
Drill the screw hole and cable hole on the wall according to
the drill template.
Loosen the set screw to disassemble the camera.
Remove the cover from the camera unit to insert the SD
card.
Install the cover back to the camera unit and fix it firmly
with the screws. Ensure even installation.
Route and connect the cables.
Secure the mounting base to the ceiling or wall using the
provided screws.

View Fullscreen

Quick Start Guide O8VT3

Welcome
Thank you for purchasing this network camera! This owner’s manual is designed to be a reference tool for your system. Please read this manual carefully before operating the unit and retain it for future reference. Should you require any technical assistance, contact Speco Technologies Tech Support at 1-800-645-5516
Important Safeguards and Warning
1. Electrical safety All installation and operation here should conform to local electrical safety codes. Use a certified/listed 12VDC Class 2 power supply or adequate PoE switch. Please note: The product must be grounded to reduce the risk of electric shock. Improper handling and/or installation could run the risk of fire or electrical shock.
2. Environment Do not expose the unit to heavy stress, violent vibration or long-term exposure to water and humidity during transportation, storage, and/or installation. Do not install near sources of heat. Only install the product in environments inside the specification operating temperature and humidity range. Do not install the camera near power lines, radar equipment or other electromagnetic radiation. Do not block any ventilation openings if any. Use all the weatherproofing hardware requirement to minimize weather intrusion.
3. Operation and Daily Maintenance Please shut down the device and then unplug the power cable before you begin any maintenance work. Do not touch the CMOS sensor optic component. You can use a blower to clean the dust on the lens surface. Always use the dry soft cloth to clean the device. If there is too much dust, use a cloth

dampened with a small quantity of neutral detergent. Finally use the dry cloth to clean the device. Please use a professional optical cleaning method to clean the enclosure. The grounding holes of the product are recommended to be grounded to further enhance the reliability of the camera. The lens is an optical device, please don’t touch or wipe cover surface directly during installation and use, please refer to the following methods if dirt is found: Stained with dirt: Use oil-free soft brush or hair dryer to remove it gently. Stained with grease or fingerprint: Use oil-free cotton cloth or paper soaked with alcohol or detergent to wipe from the lens center outward. Change the cloth and wipe several times if it is not clean enough.
Warning
This camera should be installed by qualified personnel only. All the examination and repair work should be done by qualified personnel. Any unauthorized changes or modifications could void the warranty.
Statement
. This guide is for reference only. Product, manuals and specifications may be modified without prior notice. Speco Technologies reserves the right to modify these without notice and without incurring any obligation. Speco Technologies is not liable for any loss caused by improper operation.
Note: Before installation, check the package and make sure that all components are included. Contact your rep or Speco customer service department immediately if something is broken or missing in the package.
1 Package

Camera

Quick start guide

Screwdriver

3 screws (PA 4×25mm)

3 Plastic screw anchors

Drill Template

32 OOvveerrvviieeww
1 2 3
4 5 6
7
8

1 Ethernet connector 2 Audio input connector 3 Powerconnector 4 Mounting base 5 Set screw 6 Microphone 7 Micro SD card slot 8 Reset

Water-proof connector

External microphone

DC12V

* It is recommended to install the water-proof connector for outdoor installations.
Connecting Network Cable

Loosen the nut from the main element. Run the network cable (without RJ 45 connector) through both elements. Then crimp the cable with RJ 45 connector. Connect the cable to the water-proof connector. Then tighten the nut and the main cover.

3 Installation
* Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera and the junction box.
Attach the drill template to the place where you want to install the camera and then drill the screw hole and cable hole on the wall according to the drill template.

107mm 118.5mm

120° 120°

4.4mm

Loosen the set screw to disassemble the camera. Then remove the cover from the camera unit to insert the SD card. After that, install the cover back to the camera unit and fix it firmly with the screws. (Note that the cover should not be installed unevenly .)

Set Screw Mounting Base Enclosure Camera Unit

Cover

Route and connect the cables. Then secure the mounting base to the ceiling or wall with the screws provided.
3×
PA 4×25mm
Install the camera unit and enclosure to the mounting base and then adjust if necessary to obtain an optimum view angle. Finally, fasten the camera with the set screw.

4 Web Operation and Login
IP Scanner can search for the device on the local network.
Operation Make sure that the camera and the PC are connected to the same local network. The camera is set to DHCP by default. Install IP Scanner from the CD and run it after installation.

O8VT3

5C:F2:07:24:68:9A

In the device list, you can view the IP address, model number, and MAC address of each device. Select the applicable device and double click to open up the web viewer. You can also manually enter the IP address in the address bar of the web browser.

The login interface is shown above. Default user name is admin and password is 1234. After logging in, follow directions to install applicable plugins.