78560 Rular Batten EM LED Ceiling Light Batten
Product Information
- Supply Voltage: 220-240 V~, 50 Hz
- Bulb Type:
- 78560: 24.5W LED module, 4000K
- 78561: 41W LED module, 4000K
- 78562: 52W LED module, 4000K
- 78563: 42.5W LED module, 4000K
- 78564: 65.5W LED module, 4000K
- 78565: 68.5W LED module, 4000K
- Energy efficiency class: D
- Light source: Non-replaceable
- Control gear: Replaceable by a professional
- Conformity: UKCA Directive requirements, EC Directive
requirements - Product Class: Class 1 (must be connected to earth)
- Dimming: Not suitable for dimming
Product Usage Instructions
Warning: Live Voltages may be present in this
unit even when turned off or when completely disconnected. Always
switch off the power supply before cleaning.
Layout
Before installation, existing fittings must be completely
removed. Take note of the position of each set of wires before
removing the existing fitting. Ensure that the switch is turned off
before installation and that the mounting surface is flat and
smooth for a good fit.
Wiring
This product is a Class I product and must be earthed. Join the
wires together and insulate them with good quality insulation tape
to ensure earth continuity throughout your property. Follow the
instructions below to connect the wiring from your existing light
fitting to the connection block inside the product:
Non-Maintained Wiring:
The product is normally off and comes on during a power
failure.
- Supply:
- NEUTRAL: Green/Yellow
- PERMANENT LIVE: Blue (N)
- Light Fitting:
- BROWN (L)
- BROWN (LS)
Maintained (Switched) Wiring:
The product is used as a normal light – switch on/off, light
turns on/off. It also comes on during a power failure.
- Supply:
- NEUTRAL: Green/Yellow
- PERMANENT LIVE: Blue (N)
- Light Fitting:
- BROWN (L)
- SWITCHED LIVE: BROWN (LS)
For further information, please refer to the instruction manual
for the Rular Batten EM product with model numbers 78560, 78561,
78562, 78563, 78564, or 78565. You can also visit https://www.lighting-info.co.uk/78560
for more details.
For care and safety, clean the product with a soft dry cloth. Do
not use solvents or abrasive cleaners. Dispose of waste electrical
products responsibly by recycling where facilities exist. Contact
your Local Authority or local store for recycling advice.
Thank you for purchasing this light fitting. Please read the
instructions carefully before use to ensure safe and satisfactory
operation of the product. Retain these instructions for future
reference.
Product information:
- UK Manufacturer: BH17 7BY
- EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442
Gnarrenburg - Website: www.saxbylighting.com
Technical data
Supply Voltage:
Bulb Type:
220-240 V~, 50 Hz
78560 : 78561 : 78562 : 78563 : 78564 : 78565 :
24.5W LED module, 4000K 41W LED module, 4000K 52W LED module, 4000K 42.5W LED module, 4000K 65.5W LED module, 4000K 68.5W LED module, 4000K
Duration: 3 hours (180 Minutes) Operating Temperature: 0°C-50°C Mains input current: 35mA±10% input power in mains operation: 4.5W±10% Emergency power: 1.8W-2.5W Battery Specification: LiFePO4 6.4V 1500mAH Battery Charge Time: 24 Hours Battery charge current: 250-300mA Battery warranty: 2 years
These products contain a light source of energy efficiency class D.
Non-replaceable light source
Replaceable control gear by a professional
Conformity with all relevant UKCA Directive requirements.
Conformity with all relevant EC Directive requirements.
This product is Class 1, must be connected to earth.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or local store for recycling advice.
This product is not suitable for dimming.
Care and Safety
Live Voltages may be present in this unit even when turned off or when completely disconnected. We recommend cleaning with a soft dry cloth. Do not use solvents or abrasive cleaners as these could damage the finish. For your safety, always switch off the power supply before cleaning.
Instruction manual
Rular Batten EM
78560, 78561, 78562, 78563, 78564, 78565
For further information, please visit https://www.lighting-info.co.uk/78560
V4 06/04/2022 UK Manufacturer: BH17 7BY EU Manufacturer: Brilliant AG, Brilliantstrasse 1, D-27442 Gnarrenburg
www.saxbylighting.com
Thank you for purchasing this light fitting. Please read the instructions carefully before use to ensure safe and satisfactory operation of this product. Please retain these instructions for future reference.
Warning
This is a Class 1 product and must be earthed. Please read these instructions carefully before commencing any work. This unit must be fitted by a competent and qualified electrician. Check the pack and make sure you have all the parts listed. Install in accordance with the IEE Wiring regulations and current Building Regulations. To prevent electrocution switch off at mains supply before installing or maintaining this fitting. Ensure other persons cannot restore the electrical supply without your knowledge. If you are in any doubt, please consult a qualified electrician. This light fitting should be connected to a fused circuit. If replacing an existing fitting, make a careful note of the connections. This product contains non-replaceable parts and cannot be serviced. If damage occurs the part should be scrapped. Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
Layout
Plan the desired layout of these fittings carefully, ensuring the cables will reach the distance between the junction box and the light fitting. Avoid locating any cables in positions that would cause a hazard. Position cables away from areas where they may be at risk from being cut, trapped or damaged. The mains supply cable must have a minimum cross sectional area of 1.0mm2. Cables must be protected using suitable conduit or plastic trunking. This product can be installed on the ceiling or wall.
Installation
Existing fittings must be completely removed before installation of a new product. Before removing the existing fitting, carefully note the position of each set of wires.
Note that the switch is turned off before installation.
The mounting surface must be flat and smooth to ensure a good fit.
· Starting from one end and working along, remove the LED diffuser unit by gently squeezing the sides of the metal body and lifting off the diffuser unit to one side.
· Take care to avoid damaging any concealed wiring and pipes. The correct fixings should be used for brick, cavity walls or plasterboard.
· Hold the product in place and mark the position of the fixing holes. This may require the help of an assistant. If wall mounting, ensure that the product is level.
· Ensure the ceiling or wall is capable of holding the weight of the product and then fix brackets in place.
· Feed the supply cable through the centre hole and fix the light fitting into position.
· Connect the supply cable to the quick fit terminal block as detailed wiring diagram.
Wiring
This product is Class I product must be earthed. They must be joined together and well insulated with good quality insulation tape. This is to ensure earth continuity throughout your property.
Having correctly identified the wiring from your existing light fitting and connect to the connection block inside the product in
the following way:
SUPPLY INSERT CABLE
PUSH DOWN
LIGHT FITTING
Non-Maintained Wiring: The product is normally off and comes on during a power failure.
SUPPLY
NEUTRAL GREEN/YELLOW
PERMANENT LIVE
LIGHT FITTING
BLUE ( N ) GREEN/YAELLOW ( ) BROWN ( L ) BROWN ( LS )
Maintained (Switched) Wiring: The product is used as a normal light – switch on/off, light turns on/off. Comes on during a power failure.
SUPPLY
NEUTRAL GREEN/YELLOW PERMANENT LIVE
LIGHT FITTING
BLUE ( N ) GREEN/YAELLOW ( ) BROWN ( L )
SWITCHED LIVE
BROWN ( LS )
Check that… · You have correctly identified the wires. · The connections are tight. · No loose strands have been left out of the connection block.
Commissioning · Connect the LED driver output cable to the LED diffuser unit, connect the battery output cable to EM driver. ensuring they are
securely clipped together · Refit the LED diffuser unit by clipping it into place ensuring the sides are aligned with the body. Take care not to trap any cables. · Replace fuse or circuit breaker and switch on. Your light is now ready for use.
Saxby Lighting - Commercial and Domestic Lighting Supplier
Directory Contents
